Cycle Country 25-7030 User manual

1701 38TH AVE W
PO BOX 257
SPENCER, IA 51301
PHONE: [phone]
FAX: [phone]
SERVICE: 800-841-2222
E-MAIL: [e-mail]
www.cyclecountry.com
BOMBARDIER
WINCH
MOUNT KIT
Owner’s Manual
MODEL NUMBER: 25-7030
CUSTOMER MUST RECEIVE A COPY OF THIS
OWNER’S MANUAL AT TIME OF SALE
© 2005 Cycle Country Accessories Corp.
Rev. 2
7/17/06 MAN0296

Model Number 25-7030
Parts List
Please Note:
The roller hawse, cable clamp,
and cable stop are included
with the winch.
2
3
1
7
6
8
4
9
Note: Not all parts are used in every application.
Refer to your winch instructions for specific
requirements.
5
ITEM NO. QTY. PART NO. DESCRIPTION
1 1 CYC4441 Bottom Winch Mount Plate
2 1 CYC4444 Winch Mount
3 2 PUR1325 5/16" x 3/4" Flat Head Bolt
4 4 PUR1155 5/16" x 1" Bolt Gr 5
5 4 PUR1275 Nut 5/16" Nylock
6 2 PUR1415 3/8" x 1-1/2" x 2-1/2" U-Bolt
7 4 PUR1272 Nut 3/8" Nylock
8 4 PUR1244 5/16" Flatwasher
9 2 PUR1926 8mm x 25mm Flat Head Bolt
2

THIS WINCH MOUNTING KIT CAN BE USED TO MOUNT EITHER A
CYCLE COUNTRY 1500/2500 WINCH OR A WARN 2000/2500 WINCH
TO YOUR ATV.
All directions referring to right and left are when the rider is sitting on the machine. Please Note: The
roller hawse, cable clamp, cable stop, and hardware are included with the winch.
MODEL NUMBER25-7030
WINCH MOUNT INSTALLATION INSTRUCTIONS
Note: If installing this kit with the Cycle Country 2500 or Warn 2000/2500 Winches, you Will Not
use the winch mount and four provided 5/16” bolts and nylock nuts.
1. Remove front bumper guard to ease installation.
Bottom Winch
Mount Plate
Winch Mount
Bolt thru Winch
Mount, Bottom
Winch Mount Plate
and hole on Brush
Guard
2. Place the bottom winch mount plate on top of the bottom two brush guard tubes as shown
in the picture above.
3. Position the winch mount on top of the bottom winch mount plate as shown in the picture
above and attach the winch mount to the bottom winch mount plate with two 5/16” x 1”
bolts. (The two 5/16” x 1” bolts will bolt into existing bolt holes on the brush guard.) Do
not fully tighten all attaching hardware at this time.
4. Attach the front of the bottom winch mount plate to the bottom two brush guard tubes with
two 3/8” x 1-1/2” x 2-1/2” U-bolts. Do not fully tighten all attaching hardware at this
time.
5. Go to Instructions for your winch.
3

CYCLE COUNTRY 1500 WINCH
MOUNTING INSTRUCTIONS
Using two 5/16” x 1” bolts, mount the winch to the winch mount plate. Be sure that when the
winch is mounted to the ATV, the winch motor is on the LEFT side of the machine.
(The two 5/16” x 3/4” flat head bolts or two 8mm x 25mm flat head bolts are not used in the
Cycle Country 1500 winch application).
CYCLE COUNTRY 2500 WINCH
MOUNTING INSTRUCTIONS
Using the two of the bolts PROVIDED WITH THE CYCLE COUNTRY WINCH and two
8mm x 25mm flat head bolts included in this kit, the Winch can be mounted to the bottom
winch mount plate. Be sure that when the winch is mounted to the ATV, the winch motor is to
the RIGHT side of the machine. (The two 5/16” x 3/4” flat head bolts, four 5/16” bolts and
nylock nuts and the CYC4444 winch mount are not used in the Cycle Country 2500 winch
application).
WARN 2000/2500 WINCH
MOUNTING INSTRUCTIONS
Using the two of the 5/16” x 3/4” bolts PROVIDED WITH THE WARN WINCH and two
5/16” x 3/4” flat head bolts included in this kit, the winch can be mounted to the bottom winch
mount plate. Be sure that when the winch is mounted to the ATV, the winch motor is to the
RIGHT side of the machine. (The two 8mm x 25mm flat head bolts, four 5/16” bolts and
nylock nuts and the CYC4444 winch mount are not used in the Warn 2000/2500 winch
applications).
6. Attach the roller hawse assembly to the front of the ATV brush guard with two 3/8” x 1”
bolts.
Remove one of the long rollers and the two side rollers and feed the winch cable through
the roller hawse. Reinstall the rollers and be sure rollers move freely.
Tighten attaching hardware at this time.
See Winch Wiring Instructions supplied with the Winch for proper installation.
4

CAUTION
BE AWARE OF THE CABLE STOP CONTACTING THE ROLLER
HAWSE WHEN THE CABLE IS WOUND IN.
FAILURE TO RELEASE THE SWITCH MAY CAUSE DAMAGE T
O
WINCH PARTS OR TO THE ATV.
When using the Winch to raise and lower a Cycle Country Plow, a
Cable Stop must be installed.
Hook the Winch Cable to the CYC0345 (U608) (item #4 on your 15-0001 push tube
kit) through the slotted hole. Carefully raise the blade until the top of the push tube
are no closer than 1” anywhere on the ATV. Place the Cable Stop onto the Winch
Cable up against the Winch Hawse. Secure the Cable Stop to the Winch Cable using
the Cable Clamp Assembly as shown in the pictures below.
5

ONE YEAR LIMITED WARRANTY
For the period of one year from the purchase date Cycle Country Accessories
Corporation will replace for the original purchaser, free of charge, any part or parts, when
found, upon examination by Cycle Country Accessories Corporation, to be defective in
material, workmanship, or both.
All transportation cost incurred by the purchaser in submitting the material to
Cycle Country Accessories Corporation for replacement under this warranty must be
borne by the purchaser. If Cycle Country Accessories Corporation determines that the
p
roduct must be returned to the factory for credit please call 1-800-841-2222 for an RMA
number and shipping instructions.
The warranty does not apply to parts that have been damaged by accident,
alteration, abuse, improper lubrication, normal wear, or other causes beyond Cycle
Country Accessories Corporation’s control. Products such as engines, electric motors,
and actuators may carry an original manufacturer’s warranty. Please call Cycle Country
Accessories Corporation for information.
1701 38TH AVE W
PO BOX 257
SPENCER, IA 51301
PHONE: [phone]
FAX: [phone]
SERVICE: 800-841-2222
E-MAIL: [e-mail]
www.cyclecountry.com
6

7
Cycle Country Accessories Corporation has been a world-renowned manufacturer of quality
ATV products since 1981 and we hope you will enjoy your new Cycle Country accessory.
We’re the Industry Snow Blade leader:
48”, 54”, 60” & 72” Bear Force Straight Blades 52” & 60” State Plows
72” ‘V’ Force Plow System “New” A.R.M. 52” Plow available in Poly or Steel Blade
If a winch is what you must have, then you’ve come to the right place:
1500lb and 2500lb Winches
We also have an extensive line of winch mounts for both Cycle Country and Warn winches
If you need to haul more gear on your quad, check out our baskets:
Front Basket Rear Basket Rear Drop Basket
All Purpose Basket “New” Poly Rear Drop Basket
If you need to mow the trail before you go riding one of these will help:
Our 54” finish cut Quick Silver 54 can be mounted in front or towed behind your ATV
The 48” Rough Cut will handle your toughest mowing jobs
The Rough Cut 44 provides an economical way to handle all your mowing needs
If you are into deer hunting and want to make a food plot, you will love our 3 Point
Hitch & Implements:
Rear Blade Moldboard Plow Furrower Rake
Cultivator Disk Harrow
If you have a landscaping or gardening project, check out our “Work Ready” Tow
Behind Implements:
Universal Tow Frame Cultivator Rake Rear Blade
Disc Disk Harrow
And many more accessories to help you Work Hard and Play Hard:
For more information call us at 1-800-841-2222, or on the web at www.cyclecountry.com