Cycle Country 25-5070 User manual

1701 38TH AVE W
PO BOX 229
SPENCER, IA 51301
FAX: [phone]
SERVICE: 800-841-2222
E-MAIL: [e-mail]
YAMAHA
WINCH
MOUNT KIT
Installation
Instructions
KIT NUMBER: 25-5070
CUSTOMER MUST RECEIVE A COPY
OF THIS MANUAL AT TIME OF SALE
© 2005 Cycle Country Accessories Corp.

2
#25-5070
Parts List
8
5
1
4
3
7
6
2
Please Note: The roller hawse, cable clamp and
cable stop are included with winch.
ITEM NO. QTY. PART NO. DESCRIPTION
1 1 CYC0996 Attaching Bracket
2 1 CYC0902 Roller Hawse Mount Plate
3 2 CYC0835 1" U-Clamp Black
4 2 CYC0848 7/8" U-Clamp Spacer
5 4 PUR1421 5/16" x 1-1/8" x 1-3/4" U-Bolt
6 2 PUR1194 5/16" x 2" Carriage Bolt
7 2 PUR1155 5/16" x 1" Bolt
8 12 PUR1275 5/16" Nylock Nut

THIS WINCH MOUNTING KIT CAN BE USED TO MOUNT EITHER
A CYCLE COUNTRY 1500 WINCH TO YOUR ATV.
**Some components of this kit may be already assembled. All directions referring to right
and left are when the rider is sitting on the machine. Please Note: The roller hawse, cable
clamp, cable stop, and hardware are included with the winch.
KIT #25-5070
WINCH MOUNT INSTALLATION INSTRUCTIONS
1. Remove the U-Bolts and the U-Clamps from the Winch Attaching
Bracket. Place the Winch Attaching Bracket behind the bumper and
attach it to the vertical frame tubes using the U-Bolts. Do not fully
tighten. Place the U-Clamps around the front bumper and tighten all
bolts.
2. Place the Winch on the Winch Attaching Bracket so that the motor is
facing towards the LEFT side of the ATV. Using the 5/16” x 1” Bolts
and Nylock Nuts, secure and tighten the winch.
3

3. Attach the Roller Hawse Mount Plate to the front bumper of the
ATV using 5/16” x 1-1/8” x 1-3/4” U-Bolts and Nylock Nuts.
Remove one of the long rollers and the two side rollers and feed the winch cable through
the roller hawse. Reinstall the rollers and be sure rollers move freely.
Attach the Roller Hawse to the Roller Hawse Mount Plate using the 3/8” x 1” Bolts and
Nylock Nuts provided with the winch. Tighten all hardware.
See Winch Wiring Instructions supplied with the Winch for proper installation.
4

5
CAUTION
BE AWARE OF THE CABLE STOP CONTACTING THE ROLLER
HAWSE WHEN THE CABLE IS WOUND IN.
FAILURE TO RELEASE THE SWITCH MAY CAUSE DAMAGE T
O
WINCH PARTS OR TO THE ATV.
When using the Winch to raise and lower a Cycle Country Plow, a
Cable Stop must be installed.
Hook the Winch Cable to the CYC0345 (U608) (item #4 on your 15-0001 push tube
kit) through the slotted hole. Carefully raise the blade until the top of the push tube
are no closer than 1” anywhere on the ATV. Place the Cable Stop onto the Winch
Cable up against the Winch Hawse. Secure the Cable Stop to the Winch Cable using
the Cable Clamp Assembly as shown in the pictures below.

ONE YEAR LIMITED WARRANTY
For the period of one year from the purchase date Cycle Country Accessories
Corporation will replace for the original purchaser, free of charge, any part or parts, when
found, upon examination by Cycle Country Accessories Corporation, to be defective in
material, workmanship, or both.
All transportation cost incurred by the purchaser in submitting the material to
Cycle Country Accessories Corporation for replacement under this warranty must be
borne by the purchaser. If Cycle Country Accessories Corporation determines that the
product must be returned to the factory for credit please call 1-800-841-2222 for an RMA
number and shipping instructions.
The warranty does not apply to parts that have been damaged by accident,
alteration, abuse, improper lubrication, normal wear, or other causes beyond Cycle
Country Accessories Corporation’s control. Products such as engines, electric motors,
and actuators may carry an original manufacturer’s warranty. Please call Cycle Country
Accessories Corporation for information.
1701 38TH AVE W
PO BOX 257
SPENCER, IA 51301
PHONE: [phone]
FAX: [phone]
SERVICE: 800-841-2222
E-MAIL: ccac
@
c
y
clecountr
y
.com
6

Cycle Country Accessories Corporation has been a world-renowned manufacturer of quality
ATV products since 1981 and we hope you will enjoy your new Cycle Country accessory.
We’re the Industry Snow Blade leader:
42”, 48”, 54”, 60” & 72” Straight Blades
52” & 60” State Plows
Power ‘V’ Blade
If a winch is what you must have, then you’ve come to the right place:
1500lb, 2500lb and 3000lb Winches
We also have an extensive line of winch mounts for both Cycle Country and Warn winches
If you need to haul more gear on your quad, check out our baskets:
Front Basket
Rear Basket
Rear Drop Basket
If you need to mow the trail before you go riding one of these will help:
Our 54” finish cut Quick Silver54 can be mounted in front or towed behind your ATV
The 48” Rough Cut will handle your toughest mowing jobs
The Rough Cut 44 provides an economical way to handle all your mowing needs
If you are into deer hunting and want to make a food plot, you will love our 3 Point
Hitch & Implements:
Rear Blade Moldboard Plow Spreader
Furrower Rake
Cultivator Disk Harrow
And many more accessories to help you Work Hard and Play Hard:
For more information call us at 1-800-841-2222, or on the web at www.cyclecountry.com
7