Cycle Country 25-3170 User manual

WINCH KIT
Installation
Instructions
KIT NUMBER: 25-3170
© 2005 CYCLE COUNTRY ACCESSORIES CORP.
Rev. 1
3/7/06

67
3
1
5
2
4
9
8
10
#25-3170
Parts List
Please Note:
The cable clamp, roller hawse,
and cable stop are included
with the winch.
ITEM NO. QTY. PART NO. DESCRIPTION
1 1 CYC3957 Plate, Mount
2 1 CYC4330 Bar, Support
3 1 CYC5318 Roller Hawse Mount Plate
4 3 PUR1418 5/16" x 1" x 1-3/4" U-Bolt
5 8 PUR1275 5/16" Nylock Nut
6 1 PUR1158 5/16" x 1-1/4" Bolt
7 1 PUR1155 5/16" x 1" Bolt
8 4 PUR1237 1/4" Flat Washer
9 2 PUR1265 1/4" Nylock Nut
2
10 2 PUR1118 1/4" x 1 " Bolt

THIS WINCH MOUNTING KIT CAN BE USED TO MOUNT EITHER A
CYCLE COUNTRY 1500/2000 OR A WARN 2000 TO YOUR ATV.
Please Note: The Roller Hawse, Cable Clamp, Cable Stop, and Hardware are
included with the winch.
Some components of this kit may be already assembled. All directions referring to right and left are
when the rider is sitting on the machine.
KIT #25-3170
WINCH MOUNT INSTALLATION INSTRUCTIONS
1. Assemble the Roller Hawse Mount Plate and the Roller Hawse
Assembly using the two 3/8” x 1” bolts.
2. Attach the Mount Plate to the top bumper bar with two 5/16” x 1” x 1-
3/4” U-Bolts provided. (Do not tighten hardware at this time.)
3. Align the Support Bar up to the lower center bumper bar and attach
using one 5/16”x 1”x 1-3/4” U-bolt. (Do not tighten hardware at this
time.)
4. Place the Roller Hawse Mount Plate over the two center holes on the
Mount Plate and now align the top hole of the Support Bar to the front
center hole on both the Roller Hawse Mount Plate and the Mount Plate.
Secure with the 5/16” x 1-1/4” bolt. Now, secure back center hole with
one 5/16”x 1” bolt.
3

Tighten mounting hardware at this time.
CYCLE COUNTRY 1500/2000 WINCH
MOUNTING INSTRUCTIONS
Using the 5/16” x 1” bolt and 5/16” x 1-1/4” bolt, mount the Winch and Roller Hawse Mount
Plate to the Winch Mount Plate. Be sure that when the Winch is mounted to the ATV the Winch
Motor is on the LEFT side of the machine. GO TO NEXT INSTRUCTION.
Remove one of the long rollers and the two side rollers and feed the winch cable through
the roller hawse. Reinstall the rollers and be sure rollers move freely.
See Winch Wiring Instructions supplied with the Winch for proper installation.
WARN 2000/2500 WINCH MOUNTING INSTRUCTIONS
Using the four 5/16” x 3/4” bolts PROVIDED WITH THE WARN WINCH, the Winch
can be mounted to the Winch Mounting Plate. Be sure that when the Winch is mounted to the
ATV, the Winch Motor is to the RIGHT side of the machine. GO TO NEXT INSTRUCTION.
Remove one of the long rollers and the two side rollers and feed the winch cable through
the roller hawse. Reinstall the rollers and be sure rollers move freely.
See Winch Wiring Instructions supplied with the Winch for proper installation.
4

CAUTION
BE AWARE OF THE CABLE STOP CONTACTING THE ROLLER
HAWSE WHEN THE CABLE IS WOUND IN.
FAILURE TO RELEASE THE SWITCH MAY CAUSE DAMAGE T
O
WINCH PARTS OR TO THE ATV.
When using the Winch to raise and lower a Cycle Country Plow, a
Cable Stop must be installed.
Hook the Winch Cable to the CYC0345 (U608) (item #4 on your 15-0001 push tube
kit) through the slotted hole. Carefully raise the blade until the top of the push tube
are no closer than 1” anywhere on the ATV. Place the Cable Stop onto the Winch
Cable up against the Winch Hawse. Secure the Cable Stop to the Winch Cable using
the Cable Clamp Assembly as shown in the pictures below.
5

ONE YEAR LIMITED WARRANTY
For the period of one year from the purchase date Cycle Country Accessories
Corporation will replace for the original purchaser, free of charge, any part or parts, when
found, upon examination by Cycle Country Accessories Corporation, to be defective in
material, workmanship, or both.
All transportation cost incurred by the purchaser in submitting the material to
Cycle Country Accessories Corporation for replacement under this warranty must be
borne by the purchaser. If Cycle Country Accessories Corporation determines that the
product must be returned to the factory for credit please call 1-800-841-2222 for an RMA
number and shipping instructions.
The warranty does not apply to parts that have been damaged by accident,
alteration, abuse, improper lubrication, normal wear, or other causes beyond Cycle
Country Accessories Corporation’s control. Products such as engines, electric motors,
and actuators may carry an original manufacturer’s warranty. Please call Cycle Country
Accessories Corporation for information.
1701 38TH AVE W
PO BOX 257
SPENCER, IA 51301
PHONE: [phone]
FAX: [phone]
SERVICE: 800-841-2222
E-MAIL: ccac
@
c
y
clecountr
y
.com
6

Cycle Country Accessories Corporation has been a world-renowned manufacturer of quality
ATV products since 1981 and we hope you will enjoy your new Cycle Country accessory.
We’re the Industry Snow Blade leader:
42”, 48”, 54”, 60” & 72” Straight Blades
52” & 60” State Plows
Power ‘V’ Blade
If a winch is what you must have, then you’ve come to the right place:
1500lb, 2500lb and 3000lb Winches
We also have an extensive line of winch mounts for both Cycle Country and Warn winches
If you need to haul more gear on your quad, check out our baskets:
Front Basket
Rear Basket
Rear Drop Basket
If you need to mow the trail before you go riding one of these will help:
Our 54” finish cut Quick Silver54 can be mounted in front or towed behind your ATV
The 48” Rough Cut will handle your toughest mowing jobs
The Rough Cut 44 provides an economical way to handle all your mowing needs
If you are into deer hunting and want to make a food plot, you will love our 3 Point
Hitch & Implements:
Rear Blade Moldboard Plow Spreader
Furrower Rake
Cultivator Disk Harrow
And many more accessories to help you Work Hard and Play Hard:
For more information call us at 1-800-841-2222, or on the web at www.cyclecountry.com
7