CYP PU-514LTX-1H User manual

PU-514LTX-1H
HDBaseT™ LITE Transmitter with simultaneous HDMI
output (HDMI, IR & RS-232, up to 60m)
OPERATION MANUAL

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 06/11/2013 First release

5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features..................................................7
6. Operation Controls and Functions .......8
6.1 Front Panel................................................... 8
6.2 Rear Panel..................................................... 9
6.3 IR Cable Pin Assignment .......................10
6.4. D-Sub 9 Pin Denitions ........................10
7. Connection Diagram .......................... 11
8. Specications...................................... 12
8.1 Technical Specications ........................12
8.2 CAT5e/6/7 Cable Specication ...........13
9. Acronyms............................................. 14

6
1. INTRODUCTION
The PU-514LTX-1H Transmitter allows uncompressed HDMI, and 2-way
IR signals to be transmitted over a Single CAT5e/6/7 cable to distances of
up to 60m. This device has the additional benet of a simultaneous HDMI
output for connection to a local HDMI display. Utilise the USB power
output from a TV as an optional way of powering a compatible receiver
unit alternative to using a mains power supply.
2. APPLICATIONS
Household entertainment sharing and control
Lecture room display and control
Showroom display and control
Meeting room presentation and control
Classroom display and control
3. PACKAGE CONTENTS
HDMI over HDMI & CAT5e/6/7 Transmitter
IR Blaster x 1
3.5mm Phone Jack to RS-232 Cable
24V DC Power Adaptor
Power Cord
Operation Manual
4. SYSTEM REQUIREMENTS
Source equipment with HDMI output connector
Display TV/Monitor with HDMI input connector
HDMI over CAT5e/6/7 Receivers with industry CAT5e/6/7 cables

7
5. FEATURES
HDMI 1.4 with 3D, 4K×2K support, HDCP and DVI compliant
Supports HDMI 1.4 (including HDCP) over a single CAT5e/6/7 up to
60m
Complies with HDBaseT™- Lite specications
Full HD resolution support (1080p@60Hz/36-bit), 3D over 60m, 4Kx2K
over 40m and PC resolution support (VGA to WUXGA) over CAT5e/6
cable
HDMI input up to 15m with 8-bit deep colour, or 10m with 12-bit deep
colour
Supports HDMI output up to 15m with 8/12-bit deep colour
Supports 2-way IR
Supports High Denition LPCM 7.1CH, Dolby TrueHD, Dolby Digital
Plus and DTS-HD Master Audio transmission
Choose to power the PU-514L-RX or PU-514L-WPRX receivers via the
USB output from a TV (Cable available separately - APC-USB): * Please
note the performance and consistency of USB power outputs from
TV's can vary and cannot be guaranteed by CYP.
Note:
1. This system was tested with CAT6/23AWG cables, results may vary
with cables of a dierent specication.
2. Displaying HDMI 4Kx2K resolution require the standard 4Kx2K HDMI
cable and display in order for proper image displaying.
3. This device obtain the last memory function therefore, the device
will use last CAT5e/6 output port's EDID when CAT5e/6 output is not
connected to a display after power cycling.
The unit will detect CAT5e/6 output's EDID when it obtain a 4Kx2K
EDID and send out the signal accordingly to other output ports. If
the CAT5e/6 output is without a 4Kx2K's EDID the unit will detect all
output's EDID and send out the signal that all outputs can accept.

8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
HDMI OUT HDMI IN RS232 IN
HDMI to CAT5e/6 with IR/RS232 Transmitter
1 2 3
1HDMI OUT:
Connect to HDMI display for instant image display or cascade with
another family type Transmitter.
2HDMI IN:
Connect with source equipment such as DVD/Blu-ray or PS3 player.
3RS-232 IN:
Connect to a PC/Laptop or RS-232 enabled device (with supplied
3.5mm Phone Jack to D-Sub 9-Pin adaptor) to transmit of RS-232
commands.

9
6.2 Rear Panel
POWER
DC 24V
CAT5e/6 OUT
IR 1
BLASTER USB LINK
IR 2
EXTENDER
1 2 3 4 5 6 7
1POWER LED:
Once the power supply is connected the LED will illuminate.
2DC 24V:
Plug the 24V DC power supply into the unit and connect the adaptor
to an AC outlet.
3IR 1 BLASTER:
Connect with the supplied IR Blaster to blast out the IR signal received
from the Receiver side. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled.
4IR 2 EXTENDER:
Connect with the supplied IR Extender to receive IR signal from
Transmitter side and blast out at Receiver side. Ensure that remote
controller being used is within the direct line-of-sight of the IR
Extender.
5USB:
This slot is reserved for rmware update only.
6LINK:
This LED will illuminate when CAT5e/6/7 output have been
connected to the Receiver and the Receiver have connected with
display that shows image on screen.
7CAT5e/6/7 OUT:
Connect this port to CAT5e/6/7 to HDMI Receiver with CAT5e/6/7
cable to extend the signal up to 60m.

10
6.3 IR Cable Pin Assignment
3
1
3
1
2
2
Power 3.3V
IR Blaster Signal
NC
IR Signal
Power 3.3V
Ground
IR Extender
IR Blaster
6.4. D-Sub 9 Pin Denitions
Pin Dene TX / RX
1 N/C
2 TxD/RxD
3 RxD/TxD
4 NC
5 GND
6 NC
7 NC
8 NC
9 NC