D-Link DSL-G604T User manual

QIG for Setup Wizard of DSL-G604T Page 1 of 6 03 Sept 2004
Quick Installation Guide (QIG) for Setup Wizard of DSL-G604T (040903)
(for Users in Thailand ONLY)
1. This quick installation guide is applicable to DSL-G604T with firmware version of
V1.00B02T02.EU.20040818 or higher, which includes Setup Wizard for ADSL
installation.
(Refer to Appendix A on [How to identify the firmware version of DSL-G604T])
DSL-G604T is a 3-in1 802.11g 54Mbps wireless ADSL router, which has a built-in
ADSL modem. DSL-G604T has integrated 802.11g wireless access point and a four-port
(10/100Mbps) switch. Without additional equipment, DSL-G604T allows all of the
wired & wireless computers in your home or office network to access the broadband
internet at the same time via a single ADSL telephone line.
Follow the steps below to configure DSL-G604T.
2. Configure your PC to “Obtain an IP Address Automatically” from DSL-G604T,
which is pre-configured as DHCP server. Connect you PC to DSL-G604T Ethernet port
as shown in Figure 1.
Click Network connection icon at the bottom right hand corner of Microsoft Windows
XP & follow the steps from [i] to [vi]. Once it is completed, the computer is configured
as DHCP client, which will obtain an IP address from DSL-G604T automatically.
UTP Straight
Cable

igure 1

DSL
-
G604T
RJ-11 Telephone Cable
To Telephone
Wall Socket
Step i
Step ii
Ste
p iii
Step iv
Step v
Step vi
Micro
-
Filter

QIG for Setup Wizard of DSL-G604T Page 2 of 6 03 Sept 2004
3. Run the Internet Explorer and make sure under [Tools] -> [Internet Options] ->
[Connections] -> [LAN Settings], “Proxy Server” is un-checked.
4. Step 1: Enter the default IP address 192.168.1.1 in the URL address field.
Step 2: Enter default Login Name “admin”, Password “admin” and click [OK].
5. Step 3: Click [ Run Wizard ].
Step 1 Step 2
Step 3
Step 4
Step 5

QIG for Setup Wizard of DSL-G604T Page 3 of 6 03 Sept 2004
6. Step 4: Click [ Next ].
Step 5: Select [ (GMT +7:00) Bangkok, Jakarta, Hanoi ] and click [ Next ].
7. Step 6: Select [ Select PPPoE/PPPoA ] and click [ Next ].
Setup PPPoE Connection
[Goto Section [9] for the configuration of PPPoA connection.]
8. Step 7a: Enter Username & Password of ADSL broadband account.
Step 8a: Enter the VPI & VCI values. [For True (TA) ADSL users use VPI:0 / VCI:100]
Note:
i. Both VPI and VCI values are assigned by ISP. Please obtain these values
from your ISP.
Step 9a: Select [ PPPoE LLC].
Step 10a: Click [ Next ] & go to section [10].
Step 7a
Step 8a
Step 6
Step 9a
Step 10a

QIG for Setup Wizard of DSL-G604T Page 4 of 6 03 Sept 2004
Setup PPPoA Connection
9. Step 7b: Enter Username & Password of ADSL broadband account.
Step 8b: Enter the VPI & VCI values. [For True (TA) ADSL users use VPI:0 /
VCI:100]
Note:
i. Both VPI and VCI values are assigned by ISP. Please obtain these values
from your ISP.
Step 9b: Select PPPoA LLC or PPPoA VC-Mux (Please check with your ISP.)
Step 10b: Click [ Next ] & go to section [ 10 ].
10. Step 11. Select [ Restart ] & DSL-G604T will be reset.
Step 7b
Step 8b
Step 9b
Step 10b
Step 11

QIG for Setup Wizard of DSL-G604T Page 5 of 6 03 Sept 2004
Setup Wireless
11. Step 12 & 13: Click [ Home ] and choose [ Wireless ].
12. Step 14: You may change the SSID or leave it as default – [G604T_WIRELESS]
Step 15: You may change the Channel or leave it as default – [ 6 ]
Note: Set to different non-overlapping channels - (1,6 & 11) if there are more than one
Access Points in the network.
Step 16: Click [ Apply ]
13. Step 17: Click [ Tools ]
Step 18: Click [ Misc ]
Step 19: Click [ Reboot ]
Step 12
Step 13
Step 14
Step 15
Step 16
Step 17
Step 18
Step 19

QIG for Setup Wizard of DSL-G604T Page 6 of 6 03 Sept 2004
14. Step 20: Click [ OK ]
For any assistance, kindly access www.dlink.in.th or email us suppor[email protected].
D-Link International Pte Ltd
Office: (65) 6774-6233
Fax: [phone]
Appendix A
How to Identify the Firmware Version of DSL-G604T
Step 20
Firmware version of
DSL-G604T