DANLERS BMEXPIR Quick start guide

Installation notes
DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.
Telephone: [phone] Fax: [phone]
E-mail: [email protected] Web: www.danlers.co.uk
Company Registered Number 2570169 VAT Registration Number 543 5491 38
Products available from DANLERS
• PIR occupancy switches • Daylight linked dimmers • Manual high frequency dimmers
• Photocells • Radio remote controls • Time lag switches • Outdoor security switches
• Dimmers • Heating, ventilation and air-conditioning controls • Bespoke / O.E.M. products
Please call for more information or a free catalogue.
This product conforms to BS EN 60669-2-1 and BS EN 55015.
Please ensure the most recent edition of the appropriate local wiring regulations are observed
and suitable protection is provided e.g. a 10 amp circuit breaker and voltage surge protection.
Please ensure that this device is disconnected from the supply if an insulation test is made.
This product is covered by a warranty which extends to 5 years from the date of manufacture.
Precautions and Warranty
Batten Mount Exterior PIR switch (IP66 rated)
BMEXPIR
DANLERS IP66 rated Batten Mount Exterior Passive Infra Red switch
(PIR) can be mounted onto the end of lighting battens via the 20mm
knock out. The switch includes the connection 20mm thread.
The detection range is about 5 metres over 120 degrees, the range
reduces to about 7m at the extremes to prevent nuisance switching.
On detecting movement, if the ambient light is dark enough, the
BMEXPIR will switch the load on. The ambient threshold can be set
by the user to between approximately 10 and 1000 lux via the internal
LUX adjuster (diagrams C and E). The photocell can be disabled via
the internal mode button (see overleaf).
If no more movement is detected within a pre-selected time, then
the PIR switch will turn the load off. This time lag can be set via the
TIME adjuster to 10 seconds, 20 seconds, 40 seconds, 80 seconds,
2 minutes 30 seconds, 5 minutes,10 minutes, 20 minutes or 40
minutes (diagram D).
Loading
The switch should only be connected to a 230V 50Hz AC supply.
These PIR switches can switch up to:
6 amps (1500W) of resistive loads.
6 amps (1500W) of uorescent loads.
3 amps (750W) of electronic and wire wound transformer loads.
2 amps (500W) of CFL, 2D lamps, LED Drivers and LED lamps
and ttings.
1 amp (250W) of fans
Minimum load 2W resistive, suitable for most energy saving lamps,
LEDs and emergency ttings.
12/02/16 INS568 BMEXPIR
Trouble shooting
The BMEXPIR cannot be made to switch on during bright days
• The BMEXIR should have the lux set to inactive via the internal mode
button (see diagram B)
The PIR does not detect
• Person is too far from the BMEXPIR switch, see detection diagram.
• Person is moving unusually slowly (perhaps when testing).
The PIR stops working
• Ensure the unit is mounted correctly so that no water can enter.
The PIR False triggers
• Detector is exposed to air movement on breezy days.

up to 5m
up to 7m
Strong
detection zone
i.e. person
moving arm
or walking
towards PIR
Secondary
detection zone
i.e. person
walking
perpendicular
to PIR
For optimum coverage recommended
mounting height: 2.4 to 5m
Installation procedure
1. Please read these notes carefully before commencing work.
In case of doubt please consult a qualied electrician.
Make sure the power is isolated from the circuit.
2. If mounting on a lighting batten make reference to diagram B: Remove the
20mm thread from the PIR and insert it through the 20mm knockout hole
with the thread facing outwards.
3. The detector should be connected as shown in diagram A
Brown - Live in. Blue - Neutral in. Black - Switched Line out.
4. Feed your cable through the thread and with the PIR facing downwards
tighten the 20mm thread to ensure a tight seal.
5. Make sure the power is isolated from the circuit.
7. Once the wiring has been completed and veried, switch on the supply and
test the operation.
Lux and Time set-up
For convenience, ensure that the TIME is set to minimum when setting up the
LUX level. Afterwards set the TIME to a value suitable for the application.
8. When powered up, (after 1 minute stabilisation time) turn lux pot (diagram
C) fully clockwise and time pot fully anticlockwise.
9. Press the MODE button (diagram E) for approximately 0.5s. The LED
will go green indicating the LUX cell is active. (Or press and hold button
for approx. 4 seconds – LED goes RED indicating Lux cell INACTIVE).
Repeating these steps will toggle the functionality.
10. If lux cell active, vacate area until PIR switch switches the load off (should
be after 10 seconds).
11. With the LUX as desired on working plane from daylight ONLY (no arti-
cial light), wind the lux pot anticlockwise whilst waving your hand in front
of the PIR cell. When the PIR switches the load ON, stop turning the pot.
The Lux inhibit level is now set.
12. Turn the PIR time to the desired timeout (diagram D). Whenever a person
is detected, the time lag will start again and the load will stay switched on.
Cable
gland
To light
fitting ballast
Washer
F: Detection range
B: Installation diagram, viewed from below
Precondition Power-up Condition
Lux Cell Inactive
Relay OFF
Lux Cell Inactive
Relay comes ON for 1 Min. After 1 min. ready for detection.
Lux Cell Active
Relay ON
Lux Cell Active
Relay stays ON for 1 Min. After 1 min. ready for detection.
Lux Cell Active
Relay OFF
Lux Cell Active
Relay comes ON for 1 Min. After 1 min. ready for detection.
Lux Cell Inactive
Relay ON
Lux Cell Inactive
Relay stays ON for 1 Min. After 1 min. ready for detection.
Dual colour LED:
RED - PIR active,
Photocell inactive
GREEN - PIR and
Photocell override ON
(passive LUX)
Lux Cell
Mode
Time
Delay
Spindle
Lux
Setting
Spindle
MODE
STATUS
TIME LUX
10
1000
TIME
min max
LUX
max min
10 LUX
40m
20m
10m
5m
2.5m
80s
10s
20s
40s
1000 LUX
TIME
min max
LUX
max min
10 LUX
40m
20m
10m
5m
2.5m
80s
10s
20s
40s
1000 LUX
L
load
optional manual
wall switch for
overriding off
N
230 VAC
SL
N
A: Wiring diagram
D: Time adjustment
Use Mode Button
to disable LUX (see
diagram E)
Inside detector
housing
BMEXPIR
C: Lux adjustment
E: Time/Lux adjusters (inside casing)