Installation notes
DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.
Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388
Company Registered Number 2570169 VAT Registration Number 543 5491 38
Products available from DANLERS
• PIR occupancy switches • Daylight linked dimmers • Manual high frequency dimmers
• Photocells • Radio remote controls • Time lag switches • Outdoor security switches
• Dimmers • Heating, ventilation and air-conditioning controls • Bespoke / O.E.M. products
Please call for more information or a free catalogue, or visit our website.
This product conforms to BS EN 60669-2-1, BS EN 55015 and BS EN 60730.
Please ensure the most recent edition of the appropriate local wiring regulations are observed
and suitable protection is provided (protected with the appropriate MCB) 1kV over voltage.
Please ensure that this device is disconnected from the supply if an insulation test is made.
This product is covered by a warranty which extends to 5 years from the date of manufacture.
Precautions and Warranty
15/09/16 INS309 CZ CESR 10VDC
Variants
DANLERS design and manufacture other ControlZAPP CZCESRP variants, coded
by the following order codes:
CZ CESR Suitable for mains switching
CZ CESR VF Suitable for mains switching, Volt Free contacts
CZ CESR 10VDCVF Suitable for 1-10VDC ballasts, Volt Free contacts
CZ CESR DALI Suitable for DALI ballasts
CZ CESR DALIVF Suitable for DALI ballasts, Volt Free contacts
Troubleshooting
The load will not switch on:
•TheLUXsettingasspeciedbytheControlZAPPAppissettoolowandis
inhibiting the switch.
• The moving body is not emitting more IR than the background.
(Person wearing insulating clothing in a warm environment)
• Person is too far from the PIR switch, see detection diagram.
• Person is moving unusually slowly (perhaps when testing).
• The control unit battery is not engaged (ON).
Switch RED dip switch next to the telejack connector on the CZ CESR 10VDC
control unit towards the centre of the control (see diagram D).
The load switches on when nobody is present:
• Heater causing infra-red variations in a small cold room.
Resite the CZ CESR 10VDC control away from heater.
• Please contact DANLERS for further technical support.
ControlZAPPCeilingushmountedswitches
CZ CESR 10VDC
ControlZAPP ceiling surface passive infra-red occupancy switches (PIR) can be
mounted directly onto solid ceilings or onto a range of different mounting boxes
(diagram A). These PIR switches incorporate a passive infra-red quad sensor to
detect movement of a warm body within their detection zone (diagram B) and a
photocell to monitor the ambient light level.
ALLadjustmentsaremadeviaafreelydownloadableControlZAPPApp
availablefromtheDANLERSwebsite.
If CZ CESR 10VDC is set as PIR with LUX input, upon detecting movement, if
the ambient light is dark enough, the ControlZAPP device will turn the load ON.
The ambient threshold can be set to between approximately 30 lux to 1000 lux
andinnitelux(photocellinactive)viathe‘RespondtoDaylight’settingsonthe
ControlZAPP App.
If no more movement is detected within a pre-selected time as determined by the
ControlZAPPApp,thentheControlZAPPdevicewillturntheloadoff.This‘Time
OffTimeout’ortimelagcanbesetviatheControlZAPPAppadjusterbetween
10sec and 23hrs 59min 59sec.
Loading
CZ CESR 10VDC is suitable for switching and dimming 1-10VDC ballasts. CZ
CESR 10VDC can control up to 20mA, eg. 20 ballasts at 1mA (varies according to
make and model of ballasts).
CZ CESR 10VDC can also switch up to:
• 10 amps (3000W) of resistive loads
• 6amps(1500W)uorescentlamps,highfrequencyorswitchstart,
incandescent or mains halogen lamps (recommended with integral safety fuse)
• 3 amps (750W) of electronic or wire wound transformers.
• 2 amps (500W) of low energy lamps: CFL, LED, 2D etc.
• 1 amp (250W) of fans or most metal halide lamps.
Start-upmodeandDefaultsettings
When the CZ CESR 10VDC is powered up, it will take 1 minute for the circuitry to
stabilise(detectionLEDashing)andensuretheoutputisoff,theCZCESR10VDC
will then enter its Default Operating Mode.
PleaseNote: When in the Default Operating Mode the CZ CESR 10VDC is set up
as an occupancy switch with a 20 minute turn OFF timeout (time lag) and photocell
disabled.
