De Agostini Model Space D51 200 User manual

D51 200 Steam Locomotive: STEP BY STEP
174
™
Stage 85
The base 3
Frame joint
Cap bolts × 16
Side frames A × 3
Side frame B
Side frame B should be
positioned up against the rear
frame (84) on the opposite
side to the slot.
Place the frame joint between
the assemblies from Stages 83
and 84, as shown, aligning the
cutouts of each.
Hex wrench
Assembling the base 1
1
Position the side frames, frame joint
and two assemblies as shown.
Side frames A (x3) t at the remaining
spaces between the frame joints.
83
Cutouts
84
Frame joint
Side frame A Side frame A
Side frame B
Side frame A
Slot
Side frame B
Side frame A
Required tools
Your parts

D51 200 Steam Locomotive: STEP BY STEP
175
™
Assembled parts
Assembling the base 3
3
Assembling the base 2
2
Place a cap
bolt into one
of the holes
and tighten it
by hand.
Screw a cap bolt into each of the remaining holes to secure the frame sides to the frame joints.
Align the screw holes of the frame sides and frame joints.
Use the hex
wrench to
tighten the cap
bolt fully into
the hole.
Side frame A Side frame A
Side frame BSide frame A

D51 200 Steam Locomotive: STEP BY STEP
176
™
Stage 86
The base 4
Top plate D
Top plate C
Top plate B
Top plate A
Cap bolts × 16
Place top plate B up against plate A ,
aligning the four holes in the corners
with those in the frame below.
Hex wrench
Fitting the top plates 1
1
Place top plate C onto the
frame, next to plate B.
Place top plate D at the front
end of the frame.
C BD
Place top plate A, identied by the four small holes
(circled) on top of the rear of the frame, aligning the
larger holes in the corners with those in the frame.
Small holes
Slot
Top plate A
Top plate A
Top plate B
Top plate B
Top plate C
Top plate C
Top plate D
A
Required tools
Your parts

D51 200 Steam Locomotive: STEP BY STEP
177
™
Assembled parts
Fitting the top plates 3
3
Use the hex wrench to tighten the
cap bolts fully into the holes.
Fitting the top plates 2
2
Make sure that the screw holes of the top plates are aligned with the corresponding holes in the frames below.
Insert a cap bolt into each of the 16
holes and screw into place by hand.

D51 200 Steam Locomotive: STEP BY STEP
178
™
Stage 87
Fitting the speaker
2
The speaker
Speaker protection cloth
Self-tapping screws × 12
Speaker cable
Speaker
Speaker cover
❶天板 Aの隣に、❷天板 Bを写
真の向きではめ込みます。
Phillips screwdriver
Adjust the position of the speaker so
that the four circled holes align with
those in the top plate.
Place the speaker onto
the protection cloth.
Position the cloth so that the four circled
holes are not obstructed.
Turn the base assembly over and place the
speaker protection cloth over the holes on the
underside of top plate C.
Tighten a self-
tapping screw
into each of the
four holes.
Preparing the base
1
Insert the speaker socket (attached
to the speaker) into the mount at the
side of the speaker.
Socket
Required tools
Your parts

D51 200 Steam Locomotive: STEP BY STEP
179
™
Fitting the speaker cable 1
4
Fitting the speaker cover
3
Fitting the speaker cable 2
5
Pass the other end (red plug) of the speaker cable through the next frame joint.
Place the speaker cover onto
the back of the speakers,
making sure that the socket
doesn’t come loose from its
mount.
Pass the white plug of the speaker cable
through the hole in the frame joint next to the
end of the speaker that has the socket in it.
Tighten a self-tapping screw
into each of the six circled holes
in the speaker cover.
Turn the cable
around so that
the projection is
facing upwards.
Projection
Firmly insert the plug into the
socket, as shown.
Assembled parts

D51 200 Steam Locomotive: STEP BY STEP
180
™
Stage 88
Fitting the switches
2
The switchboard
and battery box
Battery cable
Motor cable (Not used this time)
Light cable (Not used this time)
Washers × 5
Hex nuts × 10
Self-tapping screws (2.3 × 8mm) × 6
Self-tapping screws (2.6 × 8mm) × 5
Switches
Switch plate
Switchboard
Battery box
Apply instant
adhesive around the
edge of the washer.
Then glue the rest of
the washers into place
on the switchboard.
Required tools
Phillips screwdriver
Pliers
Instant adhesive
Fit a hex nut onto each of the
remaining four switches, then t
them into the switchboard, in the
order shown in the photo.
Turn the nut until it reaches
the middle of the thread.
Insert the tab of one washer
into the circled hole on the
at side of the switchboard.
Tab
Locate the projection
and tab on each washer
before using it.
Insert the end of
the switch into the
rst hole on the
switchboard, aligning
the groove with the
projection on
the washer.
Fitting the washers
1
Place a hex nut onto the threaded
part of one of the switches.
Projection
Red/black/
green/yellow
White/grey
Blue/purple
Green/yellow
Blue/red
Groove
Your parts

D51 200 Steam Locomotive: STEP BY STEP
181
™
Mounting the switch board
4
Fitting the switch plate
3
Fitting the battery box
5
Place the battery box up against the
underside of top plate B, aligning the four
screw holes in the box with those circled.
Screw a hex nut onto each of the
switches, as far as it will go.
Place the switchboard over the slot in the
side of the base, aligning the circled holes.
Tip
For ease of battery replacement, you can
choose not to install the battery box into
the base. You can assembly the battery
box outside of the base, and pass the
wire through the cutout in the frame side.
Place the switch plate over the switches
and up against the switchboard. Make
sure the four-cable switch goes through
the ‘CAB’ hole.
Half-tighten a 2.3 x 8mm
self-tapping screw into
one of the holes to hold
the board in place.
Half-tighten a 2.3 x 8mm screw
into each of the remaining
three holes. When all three are
in place, fully tighten each one.
Assembled parts
Tighten the nuts
on the back of
the switchboard
to secure the
switches in place.
Pass the socket into the slot in the base
Place the box lid
onto the back of
the battery box
and secure with a
2.3 x 8mm screw.
Be careful when using the
two screws as they are very
similar in size. They are both
8mm long and have a width
dierence of only 0.3mm.
Four cable switch
Tighten a 2.6 x 8mm
self-tapping screw into
each of the four holes in
the battery box.
Push the connector
on the end of the
battery cable onto
the one on the
battery box.
Top plate B
(hole)
Cutout