Defender Phoenix 3.5" Digital Wireless Security Video... User manual

Manual / Manuel
Phoenix™ 3.5"Digital Wireless Security Video Monitor
CAUTION: Keep small parts away from children.
ATTENTION: Gardez les petites pièces hors de la portée des enfants.
Phoenix™ 3,5po Moniteur vidéo sécurité
sans fil numérique

2
SAFETY INSTRUCTIONS
CAUTION: Keep small parts away from children.
Strangulation Hazard: Children can become entangled in cords. Power cords should be kept
more than 3 feet away from a child’s reach at all times.
This product is not a toy and should be kept out of children’s reach.
This product contains small parts. Exercise care when unpacking and assembling the product.
Read and Keep Instructions:All the safety and operating instructions should be read before the
video monitor is operated.
This product cannot replace responsible adult supervision.
Water and Moisture: This product is designed for indoor use only.The unit should not be exposed to
rain, moisture, dripping or splashing. No objects filled with liquid should be placed on top of, or beside
the product, such as a glass or vase. This item should not be used near water.
Non-Use Periods:Always unplug the AC adapters from the wall outlets during long periods of non-use.
Ventilation:This monitor should not be used on a bed, sofa, rug or similar surface that may block the
ventilation openings, or be placed in an enclosed area, such as a bookcase or drawer that may impede
air flow.
Keep Away from Sources of Heat:This unit should not be exposed to direct heat sources such as a
candle, fireplace, radiator, heat register, stove or other appliance that emits heat.The unit should not be
left in direct sunlight.
Power Source:This unit should only be used with the AC power adapters included in this package
(rated 6V 800mA).
Damage Requiring Service:This unit should be serviced by qualified personnel only when:
a. Objects have fallen or liquid has been spilled into the product
b. The units have been exposed to rain
c. The units do not appear to operate normally or exhibits a distinct change in performance
d. The units have been dropped or the enclosure damaged

3
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful inerference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IC STATEMENT / DÉCLARATION IC:
This Class B digital apparatus complies with ICES-003. / Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
This device complies with Industry Canada licence-exempt RSS 210 standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR 210 d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil
ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
FCC STATEMENT

We take quality very seriously.That is why all of our products come with a one-year warranty from the
original purchase date against defects in workmanship and materials. If you have warranty or support
issues, please contact us using any of the following methods:
Web: www.defender-usa.com Support: www.defender-usa.com/support
DEFENDER Canada DEFENDER USA
4080 Montrose Road 60 Industrial Parkway #Z64
Niagara Falls, ON Cheektowaga NY
Canada L2H 1J9 USA 14227
Warranty Terms
1. DEFENDER®products are guaranteed for a period of one year from the date of purchase against
defects in workmanship and materials.This warranty is limited to the repair, replacement or
refund of the purchase price at DEFENDER’s option.
2. This warranty becomes void if the product shows evidence of having been misused, mishandled
or tampered with contrary to the applicable instruction manual.
3. Routine cleaning, normal cosmetic and mechanical wear and tear are not covered under the
terms of this warranty.
4. The warranty expressly provided for herein is the sole warranty provided in connection with the
product itself and no other warranty, expressed or implied is provided. DEFENDER assumes no
responsibilities for any other claims not specifically mentioned in this warranty.
5. This warranty does not cover the shipping cost, insurance or any other incidental charges.
6. You MUST contact DEFENDER at www.defender-usa.com/support before sending any product
back for repair.You will be sent a Return Authorization form with return instructions.When
returning the product for warranty service, please pack it carefully in the original box with all
supplied accessories, and enclose your original receipt or copy, and a brief explanation of the
problem (include RA #).
7. This warranty is valid only in Canada and the continental U.S.
8. This warranty cannot be re-issued.
Please visit our website at
www.defender-usa.com for information
about your product’s warranty.
4

5
TABLE OF CONTENTS
SAFETY INSTRUCTIONS.................................................................................................................. 2
FCC STATEMENT............................................................................................................................ 3
WARRANTY ................................................................................................................................... 4
WHAT’S INCLUDED........................................................................................................................ 7
BUTTONS AND CONNECTIONS - MONITOR....................................................................................... 8
BUTTONS AND CONNECTIONS - CAMERA .......................................................................................10
SETUP .........................................................................................................................................11
SD card installation ......................................................................................................11
Battery installation........................................................................................................11
Connecting Power to the Monitor / Charging Battery .......................................................12
Connecting Power to the Camera ..................................................................................12
Get the Most Out of Your Rechargeable Battery...............................................................13
Screen Icons ................................................................................................................14
OPERATION..................................................................................................................................15
Turn the Monitor ON/OFF...............................................................................................15
Pairing the Camera(s) and Monitor................................................................................15
Placement of the Monitor..............................................................................................16
Placement of the Camera .............................................................................................16
Mounting the Camera on a Tabletop Safely.....................................................................16
Mounting the Camera on a Wall Safely ..........................................................................16
Night Vision..................................................................................................................17
Adjusting the Camera Angle - PTZ..................................................................................17
Volume ........................................................................................................................18
Using the 2-Way Talk Intercom.......................................................................................18
Using the Zoom function...............................................................................................19
Changing the camera view............................................................................................19
Setting an Alarm Alert - Part 1 .......................................................................................20
Setting an Alarm Alert - Part 2 .......................................................................................20
Using Power Save Mode................................................................................................21
Setting the Brightness...................................................................................................21
Taking a picture ............................................................................................................22
Recording Video ...........................................................................................................23
Viewing Saved Photos & Videos - Monitor ......................................................................24
Viewing/Deleting VIDEO - Monitor..................................................................................25
Viewing Saved Photos & Videos - Computer..................................................................25

6
TABLE OF CONTENTS
Viewing Saved Photos & Videos - Computer...................................................................26
Settings .......................................................................................................................26
SD Card formatting .......................................................................................................27
Firmware update (unused)............................................................................................27
Factory reset ................................................................................................................28
Setting the date/time ....................................................................................................29
Sound Sensitivity LED ring.............................................................................................30
180° Image Flip ...........................................................................................................31
Contacting Customer Support........................................................................................31
TROUBLESHOOTING......................................................................................................................32
MAINTENANCE.............................................................................................................................32
SPECIFICATIONS...........................................................................................................................33

7
• Night Vision PTZ Camera
• Video Monitor
• Rechargeable Battery
• 2 Power Adapters
• Mounting Hardware
• Quick Start Guide
• 1 Year Warranty
• Lifetime Customer Support
This product is intended for indoor applications only.
This product contains small parts. Exercise care when unpacking and assembling the product.
DEFENDER® does not endorse any DEFENDER® products for illegal activities. DEFENDER® is not responsible or
liable in any way for any damage, vandalism, theft or any other action that may occur while a DEFENDER® product
is in use by the purchaser.
We reserve the right to change models, configuration, or specifications without notice or liability. Product may not
be exactly as shown.
©2013 DEFENDER®.All rights reserved. DEFENDER®, the DEFENDER® logo and other DEFENDER® marks may be
registered.All other Trademarks are the property of their respective owners.
WHAT’S INCLUDED

8
FRONT / SIDE
1. LOCK / UNLOCK BUTTON
Disables ALL function buttons in the
LOCK position
2. LCD SCREEN
3. 2-WAY TALK
Press and hold to talk, release to listen
4. PAN & TILT BUTTON
5. MENU
6. MICROPHONE
7. COLOR-CHANGING LED RING
Changes color with sound intensity/battery
charge
8. SELECTION / ZOOM BUTTON
9. DIRECTIONAL ARROWS / VOLUME CONTROL
3
4
5
8
7
9
26
1
MONITOR

9
MONITOR
BACK / SIDE
1. POWER & SCREEN ON/OFF
2. POWER INPUT
3. ANTENNA
Extend to improve signal
4. TABLE STAND
5. SPEAKER
6. BATTERY COMPARTMENT
3
1
2
4
6
5

10
CAMERA
1. PTZ CAMERA
2. MICROPHONE
3. POWER LED
4. NIGHT VISION LIGHT SENSOR
5. ANTENNA
6. POWER INPUT
7. POWER ON/OFF
8. SPEAKER
1
2
3
5
46
7
8

11
LET’S GET STARTED!
SD Card Installation
1. Gently remove the BATTERY COMPARTMENT COVER on
the back of the monitor by sliding down.
2. Slide the silver bracket to the right to
unlock the MicroSD card holder. Remove
the MicroSD card from the SD card adapter
and insert the MicroSD card in the bracket
as shown - slide the silver bracket to the
left to lock the MicroSD card into place.
Battery Installation
1. Gently remove the BATTERY COMPARTMENT COVER on the back of the monitor by
sliding down.
2. Insert the battery; the battery connectors on the battery should line up with the
connectors inside the battery compartment.
3. Slide the BATTERY COMPARTMENT COVER back into place.
4. For extended periods of non-use, please remove battery from monitor.
NOTE: The monitor can support a Micro SD card UP TO 32GB.
1
2
SETUP

12
Connecting Power to the Monitor / Charging Battery
1. Connect the small end of power adapter marked MONITOR
into the DC input on the side of the monitor as shown
in the diagram. Connect the other end of the adapter into
an available wall outlet. For safety reasons, ONLY use the
adapters included in the package.
2. Press and hold the POWER button on the side of the monitor to
turn the monitor ON.
3. The icon in the top right corner of the main screen will show you the battery power status.
4. The LED Ring on the front of the monitor also indicates the battery power status.
SOLID BLUE = BATTERY FULLY CHARGED SLOW FLASHING BLUE = BATTERY CHARGING
QUICK FLASHING BLUE = BATTERY LOW FLASHING PINK = PAIRING UNSUCCESSFUL
EMPTY CHARGING FULL
Connecting Power to the Camera
1. Connect the small end of the power adapter marked
CAMERA into the DC input on the back of the camera
base as shown in the diagram. For safety reasons, ONLY
use the adapters included in the package.
2. On the side of the camera, slide the POWER switch
LEFT to the ON position.The POWER LED will light up.
LED Ring
DC Input
Power
SETUP

13
SETUP
Get the Most Out of Your Rechargeable Battery
• Fully charge battery (4 hours) before first use.
• To maximize battery life, charge battery before battery is fully drained.
• Avoid extreme heat or cold as this will affect the life of the battery.
• Turn LCD screen OFF; press POWER button on the side of the monitor ONCE.
• Set Power Save Mode:After 45 seconds of inactivity, monitor enters
standby/sleep mode.
• Set Adjustable Brightness: Decreasing screen brightness will extend battery life.
Battery life of 24 hours based on 10 audio activations while in power save mode. Battery lasts an average
of 6 hours with continuous audio/video usage.

14
SIGNAL STRENGTH
NO STRONG
SIGNAL SIGNAL
BATTERY STRENGTH
EMPTY CHARGING FULL
VOLUME
OFF LOUD
2-Way Talk
SCREEN ICONS
POWER SAVE MODE
OFF LOW MED HIGH
ALERT PICTURE VIDEO PLAY
POWER SAVE ZOOM CAMERA 180° IMAGE
FLIP
BRIGHTNESS PAIRING SUPPORT SETTINGS

15
Turn the MONITOR ON/OFF
• Press and hold the POWER button on the side of the monitor to turn the
monitor ON.
• Press and hold the POWER button again to turn OFF the monitor.
Pairing the Camera(s) and Monitor
The camera and monitor come paired (connected) to each other automatically. However, if upon
opening this package the devices do not automatically connect and transmit, you may do so manually.
**To pair additional cameras, repeat steps 1 to 4 and be sure to assign a different camera number to
each additional camera.
Note: Before you begin pairing, be sure to have the monitor and the camera(s) side by side.
OPERATION
1
2
CAMERA
BOTTOM Successfully paired
In progress
Pairing failed-restart

16
Placement of the Monitor
This monitor can be placed on a tabletop.
• You can place the monitor on a tabletop by using the retractable table stand on
the back of the monitor.When not in use, simply tuck the table stand away into the
back of the monitor until you hear a "click".
Placement of the Camera
This camera can be placed on a tabletop or hung on the wall above the
area being monitored.
• Place the camera within 15 feet of the area being monitored for best picture results.
• Do not place objects within 2 feet of the field of vision of the camera as the night vision will not
activate correctly if objects are too close.
Mounting the Camera on aTabletop Safely
1. Place the camera on a tabletop no less than 3 feet away from area being monitored.
2. Feed the power cord down the back of the table or use wall clips (not included) to secure the
cord away so children cannot reach it.
3. Plug in the power cord, check the monitor to ensure that you are getting a clear view of the
area you are monitoring and there are no obstructions.
Mounting the Camera on a Wall Safely
Before drilling the holes, it is important to check the reception and camera positioning in the intended
location on the wall.
1. Pre-drill two holes in the wall using a 3/16”, 4.8mm drill bit.
2. Insert wall anchors (not included) into each hole and tap gently with a hammer until the anchor
is flush with the wall.
3. Insert a screw (not included) into each wall anchor and tighten until the screws only stick out
about a 1/2 inch.
4. Plug the power cord into the power input of the camera.
5. Locate the wall mounting holes on the bottom of the camera base.
6. Slide the holes over the screws sticking out of the wall.
7. Confirm that the camera is secure, if it is loose you may have to tighten the screws more.
8. Use wall clips (not included) to secure the cord to prevent tripping and so children cannot reach it.
9. Connect the other end of the adapter into an available wall outlet.
OPERATION

17
Night Vision
The camera is equipped with NEW Invisible IR (infrared) LEDs which
keeps the room dark.The LEDs are located on the front of the camera
and allow you to see up to 15 feet in complete darkness allowing you
to monitor your room discretely in the dark without drawing attention to
your camera.The night vision LEDs will activate automatically when the
Light Sensor on the camera detects that the light levels are too low.
Adjusting the Camera Angle - PTZ
The camera is equipped with Pan / Tilt / Zoom (PTZ).You can adjust the angle 300° degrees horizontal
and 110° degrees vertical from the center facing position.
• Press HOME to return to exit PTZ mode and return to LIVE view.
OPERATION
INVISIBLE
LEDs
Night vision range up to 15ft under ideal conditions. Objects at or beyond this range may be partially or
completely obscured,depending on the camera application.

18
Volume
Using the 2-Way Talk Intercom
With the simple press of a button you can communicate with family members, staff and visitors from
anywhere on your property.
1. To talk, press and hold the button on the front of the monitor and release to listen.
2. To talk when using multiple cameras, select the camera in the MENU and press the button,
release to listen.
(MUTE)
Decrease / Increase
Note: Placing the monitor and camera too close together will create feedback. DECREASE or MUTE the volume
and move the camera away from the monitor.
OPERATION

19
Zoom in/out
Select
Using the ZOOM function
Changing the Camera View
• When in Quad View, volume +/– and PTZ functions default to camera 1.
• Press SELECT once desired camera view is selected.
• Press HOME to return to return to LIVE view.
• Select to cycle through cameras 1 through 4 and press the HOME button once. Each
camera view will appear for 6 seconds per camera.
1
2
Cameras 1-4
Quad view
Cycle cams 1-4
OPERATION

20
Setting an Alarm Alert - Part 1
Choose from three different Alarm Alerts that can be triggered by movement.
• Press SELECT once ALARM 1, 2 or 3 is selected.
• Press HOME to return to return to LIVE view.
1
2
Setting an Alarm Alert - Part 2
Choose 1 or up to 4 cameras that can be triggered by movement and provide an Alarm Alert once
movement is detected.
• Press SELECT once your camera(s) is(are) selected.
• Press HOME to return to return to LIVE view.
1
2
Note: Having the unit record only when motion is detected will conserve micro SD card memory.
OPERATION