Delta C2000 Series User manual

2 C S 32 C S 3
2 C E 3
50 11 69 47 03
20 13 -0 4

I
PLEASE READ PRIOR TO INSTALLATION FOR SAFETY.
DANGE
R
AC input power must be disconnected before any wiring to the AC motor drive is made.
Even if the power has been turned off, a charge may still remain in the DC-link
capacitors with hazardous voltages before the POWER LED is OFF. Please do not
touch the internal circuit and components.
There are highly sensitive MOS components on the printed circuit boards. These
components are especially sensitive to static electricity. Please do not touch these
components or the circuit boards before taking anti-static measures. Never reassemble
internal components or wiring.
Ground the AC motor drive using the ground terminal. The grounding method must
comply with the laws of the country where the AC motor drive is to be installed.
DO NOT install the AC motor drive in a place subjected to high temperature, direct
sunlight and inflammables.
CAUTION
Never connect the AC motor drive output terminals U/T1, V/T2 and W/T3 directly to the
AC mains circuit power supply.
Only qualified persons are allowed to install, wire and maintain the AC motor drives.
Even if the 3-phase AC motor is stop, a charge may still remain in the main circuit
terminals of the AC motor drive with hazardous voltages.
The performance of electrolytic capacitor will degrade if it is not charged for a long time.
It is recommended to charge the driver which is stored in no charge condition every 2
years for 3~4 hours.
Please use adjustable AC power source (ex: AC autotransformer) to charge the driver
gradually to rated voltage, and should not charge it directly with rated voltage.
Pay attention to the following when transporting and installing this package (including
wooden crate, wood stave and carton box)
1. If you need to sterilize, deworm the wooden crate or carton box, please do not
use steamed smoking sterilization or you will damage the VFD.
2. Please use other ways to sterilize or deworm.
3. You may use high temperature to sterilize or deworm. Leave the packaging
materials in an environment of over 56℃for 30 minutes.
4. It is strictly forbidden to use steamed smoking sterilization. The warranty does
not covered VFD damaged by steamed smoking sterilization.
NOTE
The content of this manual may be revised without prior notice. Please consult our distributors or download the most updated
version at http://www.delta.com.tw/industrialautomation

II
Table of Contents
CHAPTER 1 INTRODUCTION..................................................................................................................1-1
1-1 Receiving and Inspection.............................................................................................................1-1
1-2 Nameplate Information.................................................................................................................1-1
1-3 Model Name.................................................................................................................................1-1
1-4 Serial Number...............................................................................................................................1-1
1-5 RFI Jumper...................................................................................................................................1-1
1-6 Dimensions...................................................................................................................................1-1
CHAPTER 2 INSTALLATION ..................................................................................................................2-1
2-1 Minimum Mounting Clearance and Installation......................................................................1-1
2-2 Minimum mounting clearance.............................................................................................1-1
2-3 Derating Curve Diagram of Normal Duty............................................................................1-1
2-4 Derating Curve Diagram of Heavy Duty...............................................................................1-1
CHAPTER 3 UNPACKING........................................................................................................................3-1
3-1 Unpacking.......................................................................................................................................1-1
3-2 The Lifting Hook.............................................................................................................................1-1
CHAPTER 4 WIRING................................................................................................................................4-1
CHAPTER 5 MAIN CIRCUIT TERMINALS .............................................................................................5-1
5-1 Main Circuit Diagram......................................................................................................................1-1
5-2 Main Circuit Terminals....................................................................................................................1-1
CHPATER 6 CONTROL TERMINALS......................................................................................................6-1
6-1 Specifications of Control Terminal.................................................................................................1-1
6-2 Analog input terminals (AVI, ACI, AUI, ACM) ................................................................................1-1
6-3 Remove the Terminal Block...........................................................................................................1-1
CHAPTER 7 OPTIONAL ACCESSORIES.............................................................................................7-1
7-1 All Brake Resistors and Brake Units Used inAC Motor Drives.....................................................1-1
7-2 Non-fuse Circuit Breaker...........................................................................................................1-1
7-3 Fuse (Specification Chart) ...........................................................................................................1-1
7-4 AC Reactor................................................................................................. .............................1-1
7-5 Zero Phase Reactor...........................................................................................................1-1
7-6 DC Reactor................................................................................................. ..............................1-1
7-7 EMI Filter.................................................................................................. .............................1-1
7-8 Digital Keypad..................................................................................... ..........................................1-1
7-9 Panel Mounting............................................................................ ..................................................1-1
7-10 Conduit Box Kit........................................................................ .....................................1-1

III
7-11 Fan Kit................................................................................................ ...............................1-1
7-12 Flange Mounting Kit....................................................................................................................1-1
7-13 USB/RS-485 Communication Interface IFD6530......................................................................1-1
CHAPTER 8 OPTION CARDS..................................................................................................................8-1
8-1 Removed key cover
8-2 Screws Speciation for option card terminals
8-3 EMC-D42A
8-4 EMC-D611A
8-5 EMC-R6AA
8-6 EMC-BPS01
8-7 EMC-PG01L
8-8 EMC-PG01O
8-9 EMC-PG01U
8-10 EMC-PG01R
8-11 CMC-MOD01
8-12 CMC-PD01
8-13 CMC-DN01
8-14 CMC-EIP01
8-15 EMC-COP01
CHAPTER 9 SPECIFICATION..................................................................................................................9-1
9-1 230V Series
9-2 460V Series
9-3 Environment for Operation, Storage and Transportation
9-4 Specification for Operation Temperature and Protection Level
CHAPTER 10 DIGITAL KEYPAD ...........................................................................................................10-1
10-1 Descriptions of Digital Keypad
10-2 Function of Digital Keypad KPC-CC01
10-3 TPEditor Installation Instruction
10-4 Fault Code Description of Digital Keypad KPC-CC01
CHAPTER 11 SUMMARPY OF PARAMETERS.....................................................................................11-1
CHAPTER 12 DESCRIPTION OF PARAMETER SETTINGS................................................................12-1
CHAPTER 13 WARNING CODES..........................................................................................................13-1
CHAPTER 14 FAULT CODES AND DESCRIPTIONS............................................................................14-1
CHAPTER 15 CANOPEN OVERVIEW...................................................................................................15-1
CHAPTER 16 PLC FUNCTION ..............................................................................................................16-1

IV
CHAPTER 17 HOW TO SELECT THE RIGHT AC MOTOR DIRVE.......................................................17-1
CHAPTER 18 SUGGESTIONS AND ERROR CORRECTIONS FOR STANDARD AC MOTOR DRIVES
.................................................................................................................................................................18-1
CHAPTER 19 EMC STANDARD INSTALLATION GUIDE.....................................................................19-1
Application Control BD V1.03;
Keypad V1.03;

Chapter 1 IntroductionC2000 Series
1-1
Chapter 1 Introduction
1-1 Receiving and Inspection
After receiving the AC motor drive, please check for the following:
1. Please inspect the unit after unpacking to assure it was not damaged during shipment. Make sure that
the part number printed on the package corresponds with the part number indicated on the
nameplate.
2. Make sure that the voltage for the wiring lie within the range as indicated on the nameplate. Please
install the AC motor drive according to this manual.
3. Before applying the power, please make sure that all the devices, including power, motor, control
board and digital keypad, are connected correctly.
4. When wiring the AC motor drive, please make sure that the wiring of input terminals “R/L1, S/L2, T/L3”
and output terminals”U/T1, V/T2, W/T3” are correct to prevent drive damage.
5. When power is applied, select the language and set parameter groups via the digital keypad
(KPC-CC01). When executes trial run, please begin with a low speed and then gradually increases
the speed untill the desired speed is reached.
1-2 Nameplate Information
MODEL:VFD007C43A
INPUT:
Normal Duty: 3PH 380-480V 50/60Hz 4.3A
Heavy Duty: 3PH 380-480V 50/60Hz 4.1A
OUTPUT:
Version:
FREQUENCY RANGE:
Normal Duty: 3PH 0-480V 3A 2.4KVA 1HP
Heavy Duty: 3PH 0-480V 2.9A 2.3KVA 1HP
Normal Duty: 0-600Hz
Heavy Duty: 0-300Hz
VX.XX
007C43A7T9300002
DELTA ELECTRONICS. INC.
MADE IN XXXXXXX
AC Drive Model
Input Voltage/Current
Output Voltage/Current
Frequency Range
Firmware Version
Certifications
Serial Number
Enclosure type (IPXX)

Chapter 1 IntroductionC2000 Series
1-2
1-3 Model Name
1-4 Serial Number
007C43A0 T 9 30 0002
460V 3-PHASE 1HP(0.75kW)
Production number
Production week
Production year
Production factory
Model number
T: Tauyuan W: Wujian
S: Shanghai

Chapter 1 IntroductionC2000 Series
1-3
1-5 RFI Jumper
RFI Jumper: The AC motor drive may emit the electrical noise. The RFI jumper is used to suppress the
interference (Radio Frequency Interference) on the power line.
Frame A~C
Screw Torque: 8~10kg-cm(6.9-8.7 lb -in.)
Loosen the screws and remove the RFI-jumper. Fasten the screws back to the original position after
RFI-jumper is removed.

Chapter 1 IntroductionC2000 Series
1-4
Frame D0~H
Remove the RFI-jumper by hands, no screws need to be loosen.
Main power isolated from earth:
If the AC motor drive is supplied from an isolated power (IT power), the RFI jumper must be cut off. Then
the RFI capacities (filter capacitors) will be disconnected from ground to prevent circuit damage (according
to IEC 61800-3) and reduce earth leakage current.
CAUTION!
1. When power is applied to the AC motor drive, do not cut off the RFI jumper.
2. Make sure main power is switched off before cutting the RFI jumper.
3. The gap discharge may occur when the transient voltage is higher than 1,000V. Besides,
electro-magnetic compatibility of the AC motor drives will be lower after cutting the RFI jumper.
4. Do NOT cut the RFI jumper when main power is connected to earth.
5. The RFI jumper cannot be cut when Hi-pot tests are performed. The mains power and motor must be
separated if high voltage test is performed and the leakage currents are too high.
6. To prevent drive damage, the RFI jumper connected to ground shall be cut off if the AC motor drive is
installed on an ungrounded power system or a high resistance-grounded (over 30 ohms) power
system or a corner grounded TN system.

Chapter 1 IntroductionC2000 Series
1-5
1-6 Dimensions
Frame A
VFD007C23A; VFD007C43A/E; VFD015C23A; VFD015C43A/E; VFD022C23A; VFD022C43A/E;
VFD037C23A; VFD037C43A/E; VFD040C43A/E; VFD055C43A/E
Unit: mm [inch]
Frame W H D W1 H1
D1* S1 Φ1 Φ2 Φ3
A1 130.0
[5.12]
250.0
[9.84]
170.0
[6.69]
116.0
[4.57]
236.0
[9.29]
45.8
[1.80]
6.2
[0.24]
22.2
[0.87]
34.0
[1.34]
28.0
[1.10]
D1*: Flange mounting

Chapter 1 IntroductionC2000 Series
1-6
Frame B
VFD055C23A; VFD075C23A; VFD075C43A/E; VFD110C23A; VFD110C43A/E; VFD150C43A/E
Detail A (Mounting Hole)
Detail B (Mounting Hole)
See Detail A
See Detail B
Unit: mm [inch]
Frame W H D W1 H1
D1* S1 Φ1 Φ2 Φ3
B1 190.0
[7.48]
320.0
[12.60]
190.0
[7.48]
173.0
[6.81]
303.0
[11.93]
77.9
[3.07]
8.5
[0.33]
22.2
[0.87]
34.0
[1.34]
28.0
[1.10]
D1*: Flange mounting

Chapter 1 IntroductionC2000 Series
1-7
Frame C
VFD150C23A; VFD185C23A; VFD185C43A/E; VFD220C23A; VFD220C43A/E; VFD300C43A/E
Detail A (Mounting Hole)
Detail B (Mounting Hole)
See Detail A
See Detail B
Unit: mm [inch]
Frame W H D W1 H1
D1* S1 Φ1 Φ2 Φ3
C1 250.0
[9.84]
400.0
[15.75]
210.0
[8.27]
231.0
[9.09]
381.0
[15.00]
92.9
[3.66]
8.5
[0.33]
22.2
[0.87]
34.0
[1.34]
50.0
[1.97]
D1*: Flange mounting

Chapter 1 IntroductionC2000 Series
1-8
Frame D0:
D0-1: VFD370C43S, VFD450C43S
S1S1
DETAIL A
(MOUNTING HOLE)
DETAIL B
(MOUNTING HOLE)
W
W1
H1
H2
SEE DETAIL A
SEE DETAIL B
D
D1
S2
D2
H3
Frame W H1 D W1 H2 H3 D1* D2 S1 S2
D0-1 280.0
[11.02]
500.0
[19.69]
255.0
[10.04]
235.0
[9.25]
475.0
[18.70]
442.0
[17.40]
94.2
[3.71]
16.0
[0.63]
11.0
[0.43]
18.0
[0.71]
D1*：Flange Mounting

Chapter 1 IntroductionC2000 Series
1-9
Frame D0
D0-2: VFD370C43U; VFD450C43U
W
W1
H
H1
H2
SEE DETAIL A
SEE DETAIL B
D
D1
S2
D2
H3
S1
S1
DETAIL A
(MOUNTING HOLE)
DETAIL B
(MOUNTING HOLE)
1
2
3
3
2
1
Frame W H D W1 H1 H2 H3 D1* D2 S1 S2 Φ1 Φ2 Φ3
D0-2 280.0
[11.02]
614.4
[24.19]
255.0
[10.04]
235.0
[9.25]
500.0
[19.69]
475.0
[18.70]
442.0
[17.40]
94.2
[3.71]
16.0
[0.63]
11.0
[0.43]
18.0
[0.71]
62.7
[2.47]
34.0
[1.34]
22.0
[0.87]
D1*：Flange Mounting

Chapter 1 IntroductionC2000 Series
1-10
Frame D
D1: VFD300C23A; VFD370C23A; VFD370C43A; VFD450C43A; VFD550C43A; VFD750C43A
W
W1
H1
H2
S1S1
SEE DETAIL A
DETAIL A
(MOUNTING HOLE)
DETAIL B
(MOUNTING HOLE)
SEE DETAIL B
D
H3
D1
S2
D2
Unit: mm [inch]
D1*: Flange mounting
Frame W H D W1 H1 H2 H3 D1* D2 S1 S2 Φ1 Φ2 Φ3
D1
330.0
[12.99]
- 275.0
[10.83]
285.0
[11.22]
550.0
[21.65]
525.0
[20.67]
492.0
[19.37]
107.2
[4.22]
16.0
[0.63]
11.0
[0.43]
18.0
[0.71] - - -

Chapter 1 IntroductionC2000 Series
1-11
D2: VFD300C23E; VFD370C23E; VFD370C43E; VFD450C43E; VFD550C43E; VFD750C43E
W
W1
1
2
3
H
H1
H2
S1S1
SEE DETAIL A
DETAIL A
(MOUNTING HOLE)
DETAIL B
(MOUNTING HOLE)
SEE DETAIL B
3
2
1
D
H3
D1
S2
D2
Unit: mm [inch]
D1*: Flange mounting
Frame W H D W1 H1 H2 H3 D1* D2 S1 S2 Φ1 Φ2 Φ3
D2
330.0
[12.99]
688.3
[27.10]
275.0
[10.83]
285.0
[11.22]
550.0
[21.65]
525.0
[20.67]
492.0
[19.37]
107.2
[4.22]
16.0
[0.63]
11.0
[0.43]
18.0
[0.71]
76.2
[3.00]
34.0
[1.34]
22.0
[0.87]

Chapter 1 IntroductionC2000 Series
1-12
Frame E
E1: VFD450C23A; VFD550C23A; VFD750C23A; VFD900C43A; VFD1100C43A
W1
W
H2
H1
H3
D1
D
Unit: mm [inch]
Frame W H D W1 H1 H2 H3
D1* D2 S1, S2 S3 ψ1 ψ2 ψ3
E1 370.0
[14.57] - 300.0 [11.81]
335.0
[13.19
589
[23.19]
560.0
[22.05]
528.0
[20.80]
143.0
[5.63]
18.0
[0.71]
13.0
[0.51]
18.0
[0.71]
- - -
D1*: Flange mounting

Chapter 1 IntroductionC2000 Series
1-13
Frame E
E2: VFD450C23E; VFD550C23E; VFD750C23E; VFD900C43E; VFD1100C43E
W1
W
H2
H1
H3
H
D1
D
?
?
?
?
?
?
?
?
Unit: mm [inch]
Frame W H D W1 H1 H2 H3
D1* D2 S1, S2 S3 ψ1 ψ2 ψ3
E2 370.0
[14.57]
715.8
[28.18]
300.0
[11.81]
335.0
[13.19
589
[23.19]
560.0
[22.05]
528.0
[20.80]
143.0
[5.63]
18.0
[0.71]
13.0
[0.51]
18.0
[0.71]
22.0
[0.87]
34.0
[1.34]
92.0
[3.62]
D1*: Flange mounting

Chapter 1 IntroductionC2000 Series
1-14
Frame F
F1: VFD900C23A; VFD1320C43A; VFD1600C43A
H1
H2
S1
S1
W
W1
S2
See Detail A
See Detail B
Detail A (Mounting Hole)
Detail B (Mounting Hole)
D2
D
D1
H3
S3
Unit: mm [inch]
Frame W H D W1 H1 H2 H3
D1* D2 S1 S2 S3
F1 420.0
[16.54]
- 300.0
[11.81]
380.0
[14.96]
800.0
[31.50]
770.0
[30.32]
717.0
[28.23]
124.0
[4.88]
18.0
[0.71]
13.0
[0.51]
25.0
[0.98]
18.0
[0.71]
D1*: Flange mounting

Chapter 1 IntroductionC2000 Series
1-15
Frame F
F2: VFD900C23E; VFD1320C43E; VFD1600C43E
H1
H2
S1
S1
D2
W
W1
D
D1
H3
H
S2
S3
3
2
1
2
2
2
3 1
See Detail A
See Detail B
Detail A (Mounting Hole)
Detail B (Mounting Hole)
Unit: mm [inch]
Frame W H D W1 H1 H2 H3
D1* D2 S1 S2 S3
F2 420.0
[16.54]
940.0
[37.00]
300.0
[11.81]
380.0
[14.96]
800.0
[31.50]
770.0
[30.32]
717.0
[28.23]
124.0
[4.88]
18.0
[0.71]
13.0
[0.51]
25.0
[0.98]
18.0
[0.71]
Frame ψ1 ψ2 ψ3
F2 92.0
[3.62]
35.0
[1.38]
22.0
[0.87]
D1*: Flange mounting