Deltech Fitness DF9600 User manual

DF9600
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
FLAT/INCLINE BENCH
Assembly Manual

SEAT PAD
QTY 1
H
BACKREST PAD
QTY 1
G
ROLLER PADS
QTY 2
I
BOX CONTENTS
SEAT FRAME
QTY 1
A
REAR FOOT
QTY 1
B
MAIN FRAME
QTY 1
C
ADJUSTMENT SUPPORT
QTY 1
D
BACKREST MOUNT
QTY 1
E
LEG HOLD DOWN
QTY 1
F
CLAMP PLATE
QTY 1
K
ROLLER TUBE
QTY 1
J

HARDWARE
M12 x 75MM BOLT
M12 WASHER
M10 WASHER
M12 NUT
M10 x 25 MM BOLT
M12 x 150MM BOLT
RUBBER SHOE
MUSHROOM CAP
PULL-PIN
M12 x 92MM BOLT
TURN KNOB
LMNO
PQRS
TUV

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS
FOLLOWING THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM. PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER
WORK OUT ALONE- ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY. DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT. ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OF WORN OR DEFECTIVE PARTS MUST BE WITH FACTORY AUTHORIZED PARTS. IF
OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES AND
LIABILITIES BECOME VOID.
SAFETY NOTICE

TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET
Some components may be pre-installed
from the factory
(NOTE: THE NUTS USED ON THIS BENCH ARE
LOCK NUTS, THIS MEANS YOU MUST
TIGHTEN THEM DOWN PAST THE PLASTIC
INSERT.)
INSTALL RUBBER SHOES (L) ON REAR FOOT (B).
ATTACH THE REAR FOOT (B) TO FRAME (C) USING M12 x 75MM BOLTS (O), M12 WASHERS (R), CLAMP
PLATE (K), AND M12 LOCKNUTS (S).
INSTALL PULL-PIN (M) AND TURN KNOB (N) TO MAIN FRAME.
C
NM
S
R
L
L
B
K
RO

A
E
M
PR
R
S
INSTALL PULL-PIN (M) INTO SEAT FRAME (A).
ATTACH SEAT FRAME AND BACKREST MOUNT (E) TO MAIN FRAME USING M2 x 92MM BOLT (P), M12
WASHERS (R), AND M12 NUT (S).

INSTALL ADJUSTMENT SUPPORT (D) TO BACKREST MOUNT USING M12 x 150MM BOLT (Q), M12 WASHERS
(R), AND M12 LOCKNUT (S).
Q
R
R
S
D

INSTALL BACKREST PAD (G) AND SEAT PAD (H) TO SEAT FRAME AND BACKREST MOUNT USING M10 x
25MM BOLTS (T) AND M10WASHERS (U).
T
U
G
H

INSERT LEG HOLD DOWN (F) INTO MAIN FRAME AND LOCK INTO PLACE WITH PULL-PIN AND TURN KNOB.
INSERT ROLLER TUBE (J) INTO LEG HOLD DOWN UNTIL IT IS EQUAL ON BOTH SIDES.
INSTALL ROLLER PADS (I) ONTO EACH END OF ROLLER TUBE.
INSERT MUSHROOM CAP (V) INTO EACH END OF ROLLER TUBE AND HAMMER INTO PLACE WITH A
RUBBER MALLET.
V
I
JF