Deltech Fitness DF820 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
DF820/DF825
POWER RACK
Assembly Manual

BOX CONTENTS
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
A
UPRIGHT
QTY 4
B
BOTTOM CROSSMEMBER
QTY 1
C
REAR TOP CROSSMEMBER
QTY 1
D
FRONT TOP CROSSMEMBER
QTY 1
K
H
LH & RH CHIN-UP HANDLE
QTY 1 EACH
J
CORNER FLANGE
QTY 14
(2 WITH LOGO)
I
SHORT FLANGE
QTY 6
BOTTOM FRAME SUPPORT
QTY 2
F
LONG FLANGE
QTY 2
BOX 1 BOX 2 BOX 2 BOX 2
E
TOP FRAME SUPPORT
QTY 2
BOX 3 BOX 2
G
LH & RH SPOTTER ROD
BOX 3 BOX 3
BOX 3 BOX 3
BOX 3
LH & RH BAR CATCH
QTY 1 EACH
L
BOX 3
DF825
HARDWARE
QTY 1
BOX 3

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
HARDWARE
RECTANGULAR CAP
QTY 4
M
RUBBER SHOE
QTY 4
M12 WASHER
QTY 80
P
M12 x 100MM BOLT
QTY 40
M12 LOCKNUT
QTY 40
R
M10 x 75MM BOLT
QTY 4
O
HANDLE GRIP
QTY 4
N
Q S
M10 WASHER
QTY 8
T
M10 LOCKNUT
QTY 4
U

FRAME ASSEMBLY
TOOLS REQUIRED:
WRENCHES OR METRIC SOCKET SET
ATTACH THE BOTTOM CROSSMEMBER (B) TO THE BOTTOM FRAME SUPPORTS
(F) USING THE M12 x 100MM BOLTS (P), SHORT FLANGES (I), M12 WASHERS (R),
AND M12 LOCKNUTS (S). DO NOT TIGHTEN NUTS AND BOLTS AT THIS TIME.
WAIT UNTIL FRAME IS FULLY ASSEMBLED.
INSTALL THE RUBBER SHOES (M).
L
E
O
I
L
B
S
Q
Q
Q
Q
O
S
E L
I
B
F
F
M
M
M
M
P
R I
R
S

FRAME ASSEMBLY
ATTACH THE UPRIGHTS (A) TO THE BOTTOM FRAME SUPPORTS USING THE
M12 x 100MM BOLTS (P), CORNER FLANGES (K), M12 WASHERS (R), AND M12
LOCKNUTS (S). REPEAT FOR OPPOSITE SIDE.
P
A
R
P
I
P
P
R
N
I
A
A
P
R
R
K
K
S
K
K

INSERT RECTANGULAR CAP (N) INTO ENDS OF TOP FRAME SUPPORTS (E).
PLACE THE TOP FRAME SUPPORTS (E) ON TOP OF THE UPRIGHTS.
FRAME ASSEMBLY
E
E
N
N
N
N

INSTALL CORNER BRACKET (K) IN REAR USING THE 2 TOP BOLT HOLES WITH
M12 x 100MM BOLTS (P), M12 WASHERS (R), LONG FLANGE (J) AND M12
LOCKNUTS (S). INSTALL CORNER BRACKETS (K) IN FRONT USING ALL HOLES
WITH M12 x 100MM BOLTS (P), M12 WASHERS (R), AND M12 LOCKNUTS (S).
REPEAT FOR OPPOSITE SIDE.
FRAME ASSEMBLY
P
R
R
S
J
K
K
K
INSTALL LOGO CORNER FLANGE
HERE AND ON OUTER FRONT OF
OPPOSITE SIDE OF POWER RACK

ATTACH REAR TOP CROSSMEMBER (C) WITH M12 x 100MM BOLTS (P), M12
WASHERS (R), AND M12 LOCKNUTS (S).
CROSSMEMBER INSTALLATION
P
R
R
S
C

CROSSMEMBER INSTALLATION
P
R
S D
I
R
ATTACH FRONT TOP CROSSMEMBER (D) WITH M12 x 100MM BOLTS (P), M12
WASHERS(R), SHORT FLANGE (I), AND M12 LOCKNUTS (S).
AT THIS POINT, TIGHTEN ALL NUTS AND BOLTS SECURELY. THE LOCKNUTS
USED ON THIS RACK HAVE A NYLON INSERT AND YOU MUST USE ENOUGH
FORCE TO TIGHTEN THEM ON TO THE BOLT.

SLIDE HANDLE GRIPS (O) ON TO CHIN-UP HANDLES.
CHIN-UP HANDLES INSTALLATION
O
O
H

ATTACH CHIN-UP HANDLES (H) WITH M10 x 75MM BOLTS (Q), M10 WASHERS(T),
SHORT FLANGE (I), AND M10 LOCKNUTS (U).
CHIN-UP HANDLES INSTALLATION
Q
R
I
R S
H

INSERT SPOTTER RODS (G) TO DESIRED HEIGHT, MAKING SURE THAT THEY
ARE IN THE SAME NUMBER HOLE IN THE FRONT AND BACK. SLIDE IN UNTIL
BAR CATCH CONTACTS FRONT UPRIGHT. ROTATE BAR CATCH TO LOCK IT INTO
PLACE. REPEAT FOR OPPOSITE SIDE.
SPOTTER ROD INSTALLATION
G

INSERT BAR CATCHES (L) TO DESIRED HEIGHT. SLIDE IN UNTIL IT CONTACTS
UPRIGHT. ROTATE BAR CATCH TO LOCK IT INTO PLACE. REPEAT FOR OPPOSITE
SIDE.
BAR CATCH INSTALLATION
G
L

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS
FOLLOWING THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM. PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER
WORK OUT ALONE- ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY. DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT. ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OF WORN OR DEFECTIVE PARTS MUST BE WITH FACTORY AUTHORIZED PARTS. IF
OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES AND
LIABILITIES BECOME VOID.
SAFETY NOTICE