Deltech Fitness DF835 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
WEIGHT STACK ATTACHMENT
Assembly Manual
DF835

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
COMPONENTS
A
UPPER PULLEY
FRAME
QTY 1
B
BOTTOM FRAME
QTY 1 WEIGHT STACK
(19) 10 LB. PLATES
QTY 1
CD
TOP PLATE (10 LB.)
QTY 1
E
WEIGHT STACK ROD
QTY 1
F
CHROME RODS
QTY 2

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
HARDWARE
PULLEY BUSHING
QTY 2
HM10 WASHER
QTY 10
J
I
M10 x 75MM BOLT
QTY 5
M10 x 25MM BOLT
QTY 2
L
M10 LOCKNUT
QTY 5
K
K
G
PULLEY
QTY 1
RUBBER SHOE
QTY 3
M
WEIGHT STACK PIN
QTY 1
N
RUBBER DONUTS
QTY 2
OQ
CABLE
QTY 2
SPRING PIN
QTY 1
P
WEIGHT STACK
CONNECTOR
QTY 1
R

WEIGHT STACK BOTTOM FRAME ASSEMBLY
INSTALL THE RUBBER SHOES (M) 0NTO THE BOTTOM SUPPORT(B). ATTACH THE BOTTOM
SUPPORT (B) TO THE LAT ATTACHMENT USING THE M10 x 75MM BOLTS (I) M10 FLAT
WASHERS (J) AND M10 LOCK NUTS (K).
MM
I
J
J
K
B

SCREW WEIGHT STACK CONNECTOR (R)
INTO TOP OF WEIGHT STACK ROD AND
TIGHTEN WITH WRENCH.
D
P
E
INSERT WEIGHT STACK ROD (E) INTO CENTER HOLE OF
TOP PLATE (D) ALIGNING TOP HOLE OF WEIGHT STACK
ROD WITH SPRING PIN HOLE. INSERT SPRING PIN (P) AND
TAP WITH HAMMER UNTIL FLUSH WITH SURFACE.
R
WEIGHT STACK ASSEMBLY

WEIGHT STACK INSTALLATION
INSTALL THE RUBBER DOUGHNUTS (O) ONTO THE BOTTOM OF THE CHROME RODS (F) ,
LEAVING APPROXIMATELY 2” PROTRUDING. INSERT THE CHROME RODS INTO THE TWO
OUTER HOLES IN THE BOTTOM SUPPORT.
ASSEMBLE THE WEIGHT STACK (C) BY SLIDING EACH PLATE OVER THE CHROME RODS (F)
AND ON TO THE BOTTOM SUPPORT.
SLIDE THE SELECTOR ROD/TOP PLATE ASSEMBLY OVER THE CHROME RODS (F) AND
THROUGH THE WEIGHT STACK (C). INSERT THE WEIGHT STACK PIN (N) INTO THE WEIGHT
STACK (C).
N
O
F
C

UPPER PULLEYASSEMBLY INSTALLATION
REMOVE THE BOLTS, NUTS, AND WASHERS THAT HOLD THE UPPER PULLEY FRAME
ASSEMBLY TO THE BODY.
INSTALL THE UPPER PULLEY ASSEMBLY TO THE LAT ATTACHMENT USING M10 x 75MM BOLTS
(I), M10 WASHERS (J), AND M10 LOCKNUTS (K).
ATTACH THE UPPER PULLEY ASSEMBLY TO THE CHROME RODS USING M10 x25MM BOLTS (L).
INSTALL THE 4-1/2” PULLEY (G) INTO THE
UPPER PULLEY FRAME (A), USING M10 x 75MM
BOLT (I), PULLEY BUSHINGS (H), AND M10
LOCKNUT (K).
K
G
H
H
I
A
I
J
J
K
L

INSTALL UPPER CABLE OVER FRONT PULLEY, BACK TO REAR PULLEY, DOWN TO TOP
PULLEY OF FLOATING PULLEY ASSEMBLY, UP TO STACK ASSEMBLY PULLEY AND DOWN
TO SELECTOR ROD ASSEMBLY. ATTACH 8MM SNAP HOOK TO END OF CABLE AND THEN TO
SELECTOR ROD BRACKET.
NOTE: UPPER CABLE IS SHORTER
THAN THE BOTTOM CABLE
UPPER CABLE INSTALLATION
UPPER PULLEY FRAME
REMOVED FOR CLARITY
FLOATING PULLEY
ASSEMBLY

LOWER CABLE INSTALLATION
INSTALL LOWER CABLE UNDER FRONT PULLEY AND BACK TO REAR PULLEY. CONTINUE
UP AND OVER LOWER PULLEY OF FLOATING PULLEY ASSEMBLY. ATTACH SNAP HOOK TO
END OF CABLE AND THEN TO CONNECTING CHAIN. ATTACH SNAP HOOK TO THE OTHER
END OF THE CHAIN AND THEN TO FRAME POLE BRACKET. TO ADJUST CABLE TENSION
MOVE UPPER SNAP HOOK TO A DIFFERENT LINK ON CHAIN.

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS
FOLLOWING THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM. PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER
WORK OUT ALONE- ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY. DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT. ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OF WORN OR DEFECTIVE PARTS MUST BE WITH FACTORY AUTHORIZED PARTS. IF
OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES AND
LIABILITIES BECOME VOID.
SAFETY NOTICE