Deltech Fitness DF807 LEG CURL User manual

ASSEMBLY INSTRUCTIONS FOR
THE DF807 LEG CURL / LEG EXTENSION
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]

DF807
HARDWARE
QTY 1
DF807
INSTRUCTIONS
QTY 1
BOX CONTENTS
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
LEG PAD
QTY 4
A
HANDLE
QTY 1
H
SLIDE ADJUSTMENT
TUBE
QTY 2
E
FRONT FOOT
QTY 1
D
LEG PAD TUBE
QTY 2
I
WEIGHT PLATE
ROD
QTY 1
J
REAR FOOT
QTY 1
FLEG SWING
QTY 1
G
FRONT PAD
QTY 1
B
REAR PAD
QTY 1
C
BODY FRAME
QTY 1
KMOUNT
QTY 1
L

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ AL INSTRUCTIONS CAREFULLY
[phone]
HARDWARE
2” SQUARE CAP
QTY 6
M
RUBBER BUMPER
QTY 1
N
HAND GRIP
QTY 4
O
RUBBER SHOE
QTY 4
P
KNOB
QTY 2
Q
12MM x 76MM BOLT
QTY 6
S
12MM x 90MM BOLT
QTY 1
R
12MM x 76MM
CARRIAGE BOLT
QTY 2
T
12MM WASHER
QTY 15
X
W
12MM LOCKNUT
QTY 8
P
8MM x 40MM BOLT
QTY 1
V
10MM x 25MM BOLT
QTY 8
U
10MM WASHER
QTY 8
YMUSHROOM CAP
QTY 4
Z

ASSEMBLE THE FRONT FOOT (D) TO THE BODY FRAME (K) USING THE M12 x 76MM
BOLTS (S), 12MM WASHERS (X), AND 12MM LOCK NUTS (W). NOW INSTALL THE RUBBER
SHOES (P).
ASSEMBLE THE REAR FOOT (F) ONTO THE BODY FRAME (K) USING THE M12 x 76MM
BOLTS (S), 12MM WASHERS (X), AND 12MM LOCK NUTS (W). NOW INSTALL THE
RUBBER SHOES (P).
INSTALL THE SQUARE CAP (M) INTO THE END OF THE BODY FRAME. SLIDE THE HAND
GRIPS (O) ONTO THE REAR FOOT (F).
TOOLS REQUIRED:
WRENCHES OR METRIC SOCKET SET
FRAME ASSEMBLY
KD
P
P
S
X
W
X
W
P
P
X
F
O
M
S
X

INSTALL SQUARE CAP (M) IN TO THE BODY FRAME ASSEMBLY.
ATTACH THE MOUNT (L) ON TO THE BODY FRAME ASSEMBLY USING 12MM x 76MM
BOLTS (S), 12MM WASHERS (X) AND 12MM NUT (W).
BRACKET INSTALLATION
L
M
X
S
X
W

SCREW THE RUBBER BUMPER (N) ONTO THE BODY FRAME ASSEMBLY.
SLIDE THE HAND GRIPS (O) ONTO THE HANDLE (H).
ATTACH THE HANDLE (H) TO THE BODY FRAME ASSEMBLY USING THE 12MM x 76MM
CARRIAGE BOLTS (T), 12MM WASHERS (X), AND 12MM LOCK NUTS (W).
HANDLE INSTALLATION
X
W
H
T
W
N
O
Note: Handle can be mounted facing forward
or backward depending on user preference

ATTACH THE FRONT AND REAR PAD (B) & (C) TO THE BODY FRAME ASSEMBLY USING
THE 10MM x 25MM BOLTS (U) AND THE 10MM WASHERS (Y).
FRONT & REAR PAD ASSEMBLY
C
Y
U
B
Y
U
HANDLE REMOVED
FOR CLARITY

SLIDE THE 2 LEG PAD TUBES (I)
THROUGH THE ADJUSTMENT
TUBES UNTIL AN EQUAL
AMOUNT IS ON EACH SIDE.
NOW SLIDE THE WEIGHT PLATE
ROD (J) THROUGH THE LEG
SWING (G) AND ADJUST UNTIL
EVEN ON BOTH SIDES. HOLD IN
PLACE USING THE 8MM x 40MM
BOLT (V). TIGHTEN WITH
WRENCH. SLIDE RUBBER
WASHERS (Y) ONTO WEIGHT
PLATE ROD (J).
LEG EXTENSION ASSEMBLY
G
E
E
SLIDE THE ADJUSTMENT
TUBES (E) INTO EACH END OF
THE LEG SWING (G).
I
I
G
J
V

LEG EXTENSION ASSEMBLY
SLIDE THE LEG PADS (A) ONTO BOTH SIDES OF EACH OF THE LEG PAD TUBES. INSTALL
THE MUSHROOM CAPS (Z) INTO THE ENDS OF THE LEG PAD TUBES AND TAP WITH
RUBBER MALLET..
INSERT KNOBS (Q) INTO LEG SWING ASSEMBLY. INSTALL SQUARE CAPS (M) INTO EACH
TUBE END AND TAP WITH RUBBER MALLET.
M
M
M
Q
Q
V
G
Z

ATTACH THE LEG SWING ASSEMBLY TO THE BODY FRAME ASSEMBLY USING THE 12MM
x 90MM BOLT (R), 12MM WASHERS (X), AND 12MM NUT (W). TIGHTEN WITH WRENCH.
MAKE SURE ALL THE BOLTS ARE TIGHT BEFORE USE. REMEMBER TO CHECK THEM
PERIODICALLY TO ENSURE THEY ALWAYS STAY TIGHT.
LEG EXTENSION INSTALLATION
X
R
XW
Z

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS
FOLLOWING THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM. PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER
WORK OUT ALONE- ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY. DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT. ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OF WORN OR DEFECTIVE PARTS MUST BE WITH FACTORY AUTHORIZED PARTS. IF
OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES AND
LIABILITIES BECOME VOID.
SAFETY NOTICE