Deltech Fitness DF9800 User manual

DF9800
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
FLAT/INCLINE/DECLINE BENCH
Assembly Manual

BOX CONTENTS
FRONT FOOT
QTY 1
A
REAR FOOT
QTY 1
B
FRAME
QTY 1
C
LEG HOLDDOWN
TUBE
QTY 1
E
SEAT ADJUSTMENT
BASE
QTY 1
G
TELESCOPING
TUBE
QTY 1
H
ADJUSTMENT SUPPORT
QTY 1
D
BACKREST MOUNT
QTY 1
F
LEFT HAND
SEAT FLANGE
QTY 1
I

CLAMP PLATE
QTY 2
M
SEAT PAD
QTY 1
O
ADJUSTMENT FLANGE
QTY 2
N
BOX CONTENTS
ROLLER TUBE
QTY 1
K
BACKREST PAD
QTY 1
P
ROLLER PADS
QTY 2
Q
J
RIGHT HAND
SEAT FLANGE
QTY 1
J
ADJUSTMENT
LADDER
QTY 2
L

HARDWARE
M12 x 70MM BOLT
QTY 14
AA
TIGHTEN DOWN
KNOB
QTY 1
I I
M12 WASHER
QTY 34
BB
M8 WASHER
QTY 10
FF
PULL PIN
QTY 1
GG
M12 NUT
QTY 17
CC
M8 x 25 MM BOLT
QTY 10
EE
M12 x 150MM BOLT
QTY 1
DD
RUBBER SHOE
QTY 4
HH
WHEEL
QTY 2
JJ
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
MUSHROOM CAP
QTY 2
OO
M12 X 50MM BOLT
QTY 2
NN
SQUARE CAP
QTY 1
LL
RECTANGLE CAP
QTY 2
MM
ROUND CAP
QTY 4
KK
HANDLE GRIP
QTY 1
PP

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE RISK OF INJURY CAN BE REDUCED BY ALWAYS FOLLOWING
THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM. PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT, DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER
WORK OUT ALONE- ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY. DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT. ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OR WORN OR DEFECTIVE PARTS MUST BE WITH FACTORY AUTHORIZED PARTS. IF
OTHER THAN FACTORY AUTHORIZED PARTS OR ACCESSORIES ARE USED ALL WARRANTIES AND
LIABILITIES BECOME VOID.
SAFETY NOTICE
B
F
H
H
J

START BY INSTALLING RUBBER SHOES “HH” OVER REAR FOOT “B” AND FRONT
FOOT “A”.
ATTACH REAR FOOT “B” TO FRAME “C” USING M12 x 70MM BOLTS “AA”, M12
WASHERS “BB”, CLAMP PLATE “M”, AND M12 LOCKNUTS “CC”.
ATTACH FRONT FOOT “A” TO FRAME “C” USING M12 x 70MM BOLTS “AA”, M12
WASHERS “BB”, CLAMP PLATE “M”, AND M12 LOCKNUTS “CC”.
FRAME ASSEMBLY
TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET
Some components may be pre-installed
from the factory
(NOTE: THE NUTS USED ON THIS BENCH ARE
LOCK NUTS, THIS MEANS YOU MUST
TIGHTEN THEM DOWN PAST THE PLASTIC
INSERT.) PLEASE SEE BACK PAGE FOR
MORE INFORMATION
HH
B
A
C
M
AA
CC
BB
BB
HH
AA
BB
BB
CC
M
HH
HH

ATTACH ADJUSTMENT LADDERS “L” TO EACH SIDE OF THE FRAME USING M12 x
70MM BOLT “AA”, M12 WASHERS “BB”, AND M12 LOCKNUT “CC”.
INSTALL ADJUSTMENT FLANGES “N” TO FRAME USING M12 x 70MM BOLTS “AA”,
M12 WASHERS “BB”, AND M12 LOCK NUTS “CC”.
ADJUSTMENT LADDER INSTALLATION
CC
BB
L
L
BB
AA
N
AA
BB
BB CC
N

BACKREST FRAME ASSEMBLY
BB
DD
BB
CC
LL
F
D
LL
MM
MM
MM
MM
INSTALL ROUND CAPS “MM” INTO BOTH ENDS OF ADJUSTMENT SUPPORT “D”.
INSTALL RECTANGLE CAPS “LL” INTO BOTH ENDS OF BACKREST SUPPORT “F”
INSTALL ADJUSTMENT SUPPORT “D” TO BACKREST MOUNT “F’ USING
M12 x 150MM BOLT “DD”, M12 WASHERS “BB”, AND M12 LOCK NUT “CC”.
TIGHTEN NUT SECURELY, BUT MAKE SURE THAT ADJUSTMENT SUPPORT
PIVOTS FREELY. IF NECESSARY, LOOSEN JUST SLIGHTLY TO ALLOW FREE
MOVEMENT.

INSTALL BACKREST FRAME ASSEMBLY AND LEFT AND RIGHT HAND SEAT
FLANGES “I” AND “J” TO FRAME USING M12 x 70MM BOLTS “AA”, M12 WASHERS
“BB”, AND M12 LOCK NUTS “CC”.
TIGHTEN NUT SECURELY, BUT MAKE SURE THAT BACKREST FRAME PIVOTS
FREELY. IF NECESSARY, LOOSEN JUST SLIGHTLY TO ALLOW FREE MOVE-
MENT.
BACKREST FRAME & SEAT FLANGE INSTALLATION
BB
J
I
BB
AA
CC

TELESCOPING TUBE ASSEMBLY
INSTALL SQUARE CAP “MM” INTO BOTTOM OF SEAT ADJUSTMENT BASE “G”.
SLIDE TELESCOPING TUBE “H” INTO THE SEAT ADJUSTMENT BASE “G”. (YOU
WILL NEED TO LOOSEN BOLT TO ALLOW TELESCOPING TUBE TO SLIDE IN.
AFTER TELESCOPING TUBE IS INSTALLED, RETIGHTEN BOLT.)
SCREW IN PULL-PIN “GG” INTO PULL-PIN BARREL. SCREW IN TIGHTEN DOWN
KNOB “II”.
H
G
GG
I I
MM
YOU WILL NEED TO
LOOSEN THIS BOLT TO
ALLOW TELESCOPING
TUBE TO SLIDE IN

INSTALL THE TELESCOPING TUBE ASSEMBLY TO THE SEAT FLANGES AT THE TOP
AND THE ADJUSTMENT FLANGES ON THE BOTTOM USING M12 x 70MM BOLTS
“AA”, M12 WASHERS “BB”, AND M12 NUTS “CC”.
TELESCOPING TUBE INSTALLATION
AA
CC
BB
BB

ATTACH SEAT PAD “O” TO THE SEAT FLANGES USING M8 x 25MM BOLTS “EE”
AND M8 WASHERS “FF”.
SEAT INSTALLATION
EE
O
FF

SLIDE ROLLER TUBE “K” INTO LEG HOLDER TUBE “E”. SLIDE ROLLER PADS “Q”
ONTO ROLLER TUBE ON EACH END. INSERT MUSHROOM CAPS “OO” ONTO
ROLLER TUBE AND INSTALL WITH RUBBER MALLET. SLIDE HANDLE GRIP “PP”
ONTO HANDLE OF LEG HOLDER TUBE.
INSTALL LEG HOLDER TUBE “E” TO FRONT OF SEAT FLANGES USING M12 x
70MM BOLTS “AA”, M12 WASHERS “BB”, AND M12 LOCK NUTS “CC”.
ATTACH BACKREST PAD “P” TO THE BACKREST MOUNT USING M8 x 25MM
BOLTS “EE” AND M8 WASHERS “FF”.
BACKREST AND LEG HOLDDOWN ASSEMBLY
FF
EE P
AA
BB
CC
BB
Q
Q
OO
OO
K
E
PP

WHEEL INSTALLATION
USE M12 x 50MM BOLTS “NN” AND M12 NUTS “CC” TO ATTACH WHEELS “JJ” TO
THE BACK FOOT.
JJ
NN
CC

THE LOCKNUT GUIDE
ALL DELTECH FITNESS
PRODUCTS COME WITH
LOCKNUTS. LOCKNUTS ARE
NUTS WITH A SPECIAL PLASTIC
PIECE PRESSED INTO THE TOP
“A”
IF YOUR WEIGHT EQUIPMENT
FEELS WOBBLEY AND UNSAFE
IT COULD BE BECAUSE YOU DO
NOT HAVE YOUR LOCKNUTS
TIGHT ENOUGH. LOCKNUTS CAN
NOT BE TIGHTENED ALL THE
WAY BY HAND.
TO TIGHTEN A LOCKNUT
CORRECTLY YOU MUST USE A
WRENCH. THIS WILL ENSURE
THAT YOU TIGHTEN THE
LOCKNUT PAST THE PLASTIC
PIECE ONTO THE BOLT.
A
A CORRECTLY TIGHTENED NUT
SHOULD LOOK LIKE THIS. EVEN
THOUGH LOCKNUTS DO NOT
COME LOOSE EASILY, WITH
HEAVY USE ON YOUR
EQUIPMENT, YOU SHOULD
TIGHTEN THEM PERIODICALLY.