Deltech Fitness DF830 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
DF830
LAT ATTACHMENT
Assembly Manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
DF830
HARDWARE
QTY 1 DF830
INSTRUCTIONS
BOX CONTENTS
F
WEIGHT CARRIAGE
QTY 1
D
LOW BAR
QTY 1
C
LAT BAR
QTY 1
E
CABLE
QTY 2
J
4” FLANGE
QTY 2
I
PULLEY FLANGE
QTY 2
A
TOP FRAME
QTY 1
B
BOTTOM SUPPORT
QTY 1
G
REAR SUPPORT
TUBE
QTY 1
H
FRONT SUPPORT
TUBE
QTY 1

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
HARDWARE
K
K
4-1/2” PULLEY
QTY 3
3-1/2” PULLEY
QTY 4
L
10” CHAIN
QTY 2
N
QUICK CLIP
QTY 2
X
PULLEY BUSHING
QTY 6
M
SNAP HOOK
QTY 6
W
M12 x 75MM BOLT
QTY 4
O
M10 x 70MM
BOLT
QTY 3
Q
M12 x 65MM BOLT
QTY 2
P
M10 WASHER
QTY 8
V
M10 LOCKNUT
QTY 7
T
M12 LOCKNUT
QTY 8
S
M10 x 45MM BOLT
QTY 4
R
M12 WASHER
QTY 14
U
M12 x 105MM BOLT
QTY 2
Y

TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET
ATTACH THE BOTTOM SUPPORT (B) TO THE BOTTOM CROSSMEMBER OF THE POWER
RACK OR SMITH MACHINE YOU ARE INSTALLING TO USING M12 x 75MM BOLTS (O), 4”
FLANGE PLATES (J), M12 WASHERS (U) AND M12 LOCKNUTS (S). TIGHTEN SECURELY.
FRAME ASSEMBLY
(NOTE: THE NUTS USED ON THIS ARE
LOCKNUTS, THIS MEANS YOU MUST
TIGHTEN THEM DOWN PAST THE
PLASTIC INSERT.)
B
O
U
S
U
J

INSTALL THE REAR SUPPORT TUBE (G) TO THE BOTTOM SUPPORT (B) ALIGNING HOLES
IN FLANGE WITH PIN AND THREADED STUD. INSTALL 12MM WASHER (U) AND 12MM
NUT (S) AND TIGHTEN.
INSTALL THE FRONT SUPPORT TUBE (H) TO THE BOTTOM SUPPORT (B) ALIGNING HOLES
IN FLANGE WITH PIN AND THREADED STUD. INSTALL 12MM WASHER (U) AND 12MM
NUT (S) AND TIGHTEN.
FRAME ASSEMBLY
H
G
B
U
S

LOWER PULLEY ASSEMBLY
F
INSTALL THE 4-1/2” PULLEY (K) INTO THE CENTER FLANGES OF THE BOTTOM
SUPPORT USING THE M10 x 45MM BOLT (R), 10MM WASHERS (V), AND M10 LOCK-
NUT (T).
INSTALL THE 3-1/2” PULLEY (L) INTO THE FRONT FLANGES OF THE BOTTOM
SUPPORT USING THE M10 x 45MM BOLT (R), 10MM WASHERS (V), AND M10 LOCK-
NUT (T).
M
T
V
V
R
K
L

INSTALL THE WEIGHT CARRIAGE ASSEMBLY ONTO THE REAR FRAME WITH THE
WEIGHT BAR FACING FORWARD. SLIDE DOWN UNTIL IT RESTS ON THE RUBBER
BUMPER.
FRAME ASSEMBLY
DISREGARD THIS STEP IF USING
WITH STACK LOADED ATTACHMENT

ATTACH THE FRONT OF THE TOP FRAME ASSEMBLY TO THE POWER RACK WITH M12 x
75MM BOLTS (O), M12 WASHERS (U), 4” FLANGE (J), AND LOCKNUTS (S). (IF YOU ARE
ATTACHING TO DF4900 SMITH MACHINE USE M12 x 105MM BOLTS INSTEAD)
ATTACH THE BACK OF THE TOP FRAME ASSEMBLY TO THE FRAME SUPPORT TUBES
WITH M12 x 65MM BOLTS (P), M12 WASHERS (U), AND LOCKNUTS (S). SECURELY
TIGHTEN ALL BOLTS.
FRAME ASSEMBLY
P
U
U
S
O
U
U
S
J
IIF YOU ARE ATTACHING TO
DF4900 SMITH MACHINE, USE
ITEM Y- M12 x 105MM BOLTS

ASSEMBLE THE FLOATING PULLEY ASSEMBLY USING THE 4-1/2” PULLEYS (K), THE
PULLEY FLANGES (I), THE M10 x 45MM BOLTS (R), THE 10MM FLAT WASHERS (V), AND
THE 10MM LOCKNUTS (T).
FLOATING PULLEY ASSEMBLY
(NOTE: THE NUTS USED ON THIS
BENCH ARE LOCK NUTS, THIS MEANS
YOU MUST TIGHTEN THEM DOWN
PAST THE PLASTIC INSERT.)
K
R
V
V
T
I

UPPER CABLE INSTALLATION
THE UPPER AND LOWER CABLES ARE THE SAME.
STARTING WITH THE CABLE END WITHOUT THE BALL, INSERT CABLE INTO FRONT
OPENING OF THE UPPER PULLEY FRAME AND FEED IT TOWARDS THE BACK. PULL CABLE
END OUT THROUGH REAR OPENING.

UPPER CABLE INSTALLATION
INSERT 3-1/2” PULLEY (L) INTO FRONT OPENING OF UPPER PULLEY FRAME AND INSTALL
USING THE M10 x 70MM BOLT (Q), PULLEY BUSHINGS (M), AND M10 LOCKNUT (T).
REPEAT FOR MIDDLE PULLEY.
M
M
L
L
Q
T

UPPER CABLE INSTALLATION
FEED CABLE END AROUND TOP PULLEY OF FLOATING PULLEY ASSEMBLY AND THEN
OVER 3-1/2” PULLEY. INSTALL 3-1/2” PULLEY IN UPPER PULLEY FRAME USING THE M10 x
70MM BOLT (Q), PULLEY BUSHINGS (M), AND M10 LOCKNUT (T).
M
M
Q
T

UPPER CABLE INSTALLATION
ATTACH SNAP END OF CABLE AND ATTACH TO FLANGE ON WEIGHT SLIDE.

LOWER CABLE INSTALLATION
STARTING WITH THE CABLE END WITHOUT THE BALL, INSERT CABLE UNDER 3-1/2”
PULLEY ON FRONT SUPPORT TUBE. MAKE SURE THAT CABLE IS BELOW PULLEY AND
ABOVE KEEPER BAR ON BOTTOM OF PULLEY FRAME (SEE INSET PICTURE)
KEEPER BAR

LOWER CABLE INSTALLATION
FEED CABLE THROUGH OPENING IN FRONT SUPPORT TUBE. INSTALL CABLE AROUND 4-1/2”
LOWER PULLEY, UP AND AROUND BOTTOM PULLEY OF FLOATING PULLEY ASSEMBLY.
ATTACH SNAP HOOKS TO BOTH ENDS OF CHAIN. ATTACH ONE END TO CABLE AND THE
OTHER END TO MOUNTING FLANGE ON FRONT SUPPORT TUBE.

ATTACH LAT BAR TO UPPER CABLE WITH SNAP HOOK. MOVE TO CRADLE WHEN NOT IN
USE.
LAT BAR INSTALLATION
ATTACH LOW ROW BAR TO LOWER CABLE WITH 2 SNAP HOOKS AND CHAIN. YOU CAN
ALSO USE THIS CHAIN ON THE HIGH PULLEY TO DO TRICEP EXERCISES.
LOW ROW BAR INSTALLATION

CHECK TO MAKE SURE ALL CABLES ARE IN THE V GROOVE OF THE PULLEYS.
CHECK ALL PULLEYS TO MAKE SURE THEY ROTATE FREELY.
TROUBLESHOOTING TIPS
1. CABLE WILL NOT MOVE OR RUBS
2. SEAT OR LEG HOLD-DOWN WON’T ADJUST
MAKE SURE THE TIGHTEN DOWN KNOB IS LOOSENED BEFORE MAKING ADJUSTMENTS.
3. MACHINE NOT OPERATING SMOOTHLY
MAKE SURE BOTH PLASTIC GUIDES ON WEIGHT SLIDE ASSEMBLY ARE FULLY SEATED AND
HAVE NOT WORKED LOOSE.
USE SILICONE SPRAY OR SIMILAR LUBRICANT ON REAR SUPPORT TUBE AND PLASTIC
GUIDES ON WEIGHT SLIDE ASSEMBLY.

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS
FOLLOWING THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM- PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT, DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT, DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER
WORK OUT ALONE -ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OR WORN OR DEFECTIVE PARTS MUST BE REPLACE WITH FACTORY AUTHORIZED
PARTS. IF OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES
AND LIABILITIES BECOME VOID.
SAFETY NOTICE