Denon DVP-602CI User manual

V.5.6.0
- 1 -
DENON DVP-602CI control protocol
Application model : DVP-602CI
AMX Rev Ver. DVP-602CI:5.6.0
Application terminal : RS-232C/ Ethernet
Connector specification
Ⅰ. RS-232C
Connector type: DB-9pin female type, slave straight connection (DCE type)
( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )
Communication format:
Synchronous system : Tone step synchronization
Communication system : A half duplex
Communication speed : 9600bps
Character length : 8 bits
Parity control : None
Start bit : 1 bit
Stop bit : 1 bit
Communication procedure : Non procedural
Communication data length : 135 bytes (maximum)

V.5.6.0
- 2 -
Ⅱ. Ethernet
Connector type ：RJ-45(10BASE-T/100BASE-TX)
Communication format ：
Communication system : A half duplex
Communication speed : 10Mbps/100Mbps
Communication port : TCP port 23 (telnet)
Communication data length : 135bytes (maximum)
PC
DVP-602CI
Ethernet
Cross cable
PC
DVP-602CI
HUB
Ethernet
Straight
cable
Ethernet
Straight
cable
Example ①
Example ②

V.5.6.0
- 3 -
NETWORK SETUP of DVP-602CI
>Procedure of Network Setup mode.
(1)Press Setup button, then Setup menu appears on FL-display(and GUI)
(2)Select “Setup > Network Setup > Network Setup > Detail” .
(3)Set parameters described below.
<DHCP> "ON"---Use this setting when DHCP server is on the local network.
"OFF"---Use this setting when DHCP server is not on the local network.
<IP Address> When <DHCP> sets "OFF”, please set IP address.
When <DHCP> sets "ON”, you can confirm the IP address that is set by server.
<Subnet Mask> When <DHCP> sets "OFF”, please set Subnet Mask.
When <DHCP> sets "ON”, you can confirm the Subnet Mask that is set by server.
<Gateway> Set the address of Gateway when Gateway is on the local network.
Do not set this parameter when Gateway is not on the local network.
<Primary DNS> Do not set this parameter.
<Second DNS> Do not set this parameter.
<Proxy> Set this parameter "OFF".
<Network Option: Standby Mode Power Saving>
(1)Press Setup button, then Setup menu appears on FL-display(and GUI)
(2)Select “Setup > Network Setup > Power Saving”
(3)Set parameters described below.
“OFF”---Use this setting when using the DVP-602CI connected in a network.
“ON”--- Use this setting when not using the DVP-602CI connected in a network.
This setting is reducing the power consumption in the standby mode.

V.5.6.0
- 4 -
Protocol specification
The following three data forms are defined.
COMMAND : The message sent to a system(DVP-602CI) from a controller(Touch Panel etc.)
A command to a system is given from a controller.
EVENT : The message sent to a controller(Touch Panel etc.) from a system(DVP-602CI)
The result is sent, when a system is operated directly and a state changes.
*The form of EVENT presupposes that it is the same as that of COMMAND.
**Refer to the following table for the contents of COMMAND and EVENT.
RESPONSE : The message sent to a controller(Touch Panel etc.) from a system(DVP-602CI)
if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller.
The RESPONSE should be sent within 200ms of receiving the COMMAND.
*The form of RESPONSE presupposes that it is the same as that of EVENT.
Basic specification : The command by ASCII CODE, parameter expression
*ASCII CODE which can be used is from 0x20 to 0x7F : the alphabet and the number of 0-9 , and space (0x20) , Some signs ,
AND carriage return(0x0D)--- It is used only as a pause sign.
Command structure : COMMAND + PARAMETER + CR(0x0D)
COMMAND : ASCII CODE of 2 characters
ex. SI : Select Input source
PW : system PoWer setting
PARAMETER : ASCII CODE ( up to 25 characters)
ex. HDMI1 : function name
COM1 : function name
*Special Parameter--- ? : for request command

V.5.6.0
- 5 -
The example of a command * <CR> is the meaning of 0x0D.
SIHDMI1<CR> : Select Input source HDMI1
PWON<CR> : system Power ON
PWSTANDBY<CR> : system Power STANDBY
SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’

V.5.6.0
- 6 -
Others
A) COMMAND is receivable also during transmission of EVENT.
B) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to
the another request commands(ex. SV command).
C) Four seconds later, please transmit the next COMMAND after transmitting a power on COMMAND（PWON）.

V.5.6.0
- 7 -
COMMAND and PARAMETER list
COMMAND PARAMETER function example
PW ON POWER ON/STANDBY change PWON<CR>
STANDBY PWSTANDBY<CR>
? Request PW Status PW?<CR>
HDMI1 SIHDMI1<CR>
HDMI2 SIHDMI2<CR>
HDMI3 SIHDMI3<CR>
HDMI4 SIHDMI4<CR>
HDMI5 SIHDMI5<CR>
HDMI6 SIHDMI6<CR>
COMPONENT1 SICOMPONENT1<CR>
COMPONENT2 SICOMPONENT2<CR>
S-VIDEO SIS-VIDEO<CR>
SI
VIDEO
Select INPUT source
SIVIDEO<CR>
AUTO set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG) SDAUTO<CR>
HDMI set force HDMI INPUT mode SDHDMI<CR>
DIGITAL set force DIGITAL INPUT (Optical, Coaxial, BNC)mode SDDIGITAL<CR>
SD
? Return SD Status SD?<CR>

V.5.6.0
- 8 -
PS COMMAND : "*" parameter uses two or three ASCII characters. (see page 6 J) section)
COMMAND PARAMETER function example
VS MONIAUTO Set HDMI MONITOR automatic detection VSMONIAUTO<CR>
MONI1 Set HDMI MONITOR OUT-1 VSMONI1<CR>
MONI2 Set HDMI MONITOR OUT-2 VSMONI2<CR>
MONI? Return VSMONITOR Status VSMONI?<CR>
ASPNRM Set Normal mode VSASPNRM<CR>
ASPFUL Set FULL mode VSASPFUL<CR>
ASP? Return VSASPECT Status VSASP?<CR>
SC48P Set Resolution to 480p/576p VSSC48P<CR>
SC10I Set Resolution to 1080i VSSC10I<CR>
SC72P Set Resolution to 720p VSSC72P<CR>
SC10P Set Resolution to 1080p VSSC10P<CR>
SC10P24 Set Resolution to 1080p/24 VSSC10P24<CR>
SCVGA Set Resolution to VGA VSSCVGA<CR>
SCSVGA Set Resolution to SVGA VSSCSVGA<CR>
SCXGA Set Resolution to XGA VSSCXGA<CR>
SCWXGA Set Resolution to WXGA VSSCWXGA<CR>
SCWXGA2 Set Resolution to WXGA2 VSSCWXGA2<CR>
SCSXGA Set Resolution to SXGA VSSCWSXGA<CR>
SCAUTO Set Resolution to AUTO VSSCAUTO<CR>
SC? Return VSSCALE Status VSSC?<CR>
IPMAUT HDMI Progressive mode:AUTO VSIPMAUT<CR>
IPMVI1 HDMI Progressive mode:VIDEO1 VSIPMVI1<CR>
IPMVI2 HDMI Progressive mode:VIDEO1 VSIPMVI2<CR>
COMMAND PARAMETER function example
PS DELAY UP AUDIO DELAY UP/DOWN, direct change to ***dB PSDELAY UP<CR>
DELAY DOWN ***:000 to 999 by ASCII, 000=0ms, 200=200ms PSDELAY DOWN<CR>
DELAY *** ---DVP-602CI can be operated from 0 to 200 PSDELAY 200<CR>

V.5.6.0
- 9 -
COMMAND PARAMETER function example
PV CN UP CONTRAST UP/DOWN, direct change to **dB PVCN UP<CR>
CN DOWN **:44 to 56 by ASCII, 50=0 PVCN DOWN<CR>
CN ** --- DVP-602CI can be operated from -6 to +6(44 to 56) PVCN 50<CR>
CN ? Return PVCN Status PVCN ?<CR>
BR UP BRIGHTNESS UP/DOWN, direct change to **dB PVBR UP<CR>
BR DOWN **:00 to 12 by ASCII, 00=0 PVBR DOWN<CR>
BR ** --- DVP-602CI can be operated from 0 to 12 PVBR 12<CR>
BR ? Return PVBR Status PVBR ?<CR>
CM UP CROMA LEVEL UP/DOWN, direct change to **dB PVCM UP<CR>
CM DOWN **:44 to 56 by ASCII, 50=0 PVSCM DOWN<CR>
CM ** --- DVP-602CI can be operated from -6 to +6(44 to 56) PVCM 50<CR>
CM ? Return PVCN Status PVCM ?<CR>
HUE UP HUE UP/DOWN, direct change to **dB PVHUE UP<CR>
HUE DOWN **:44 to 56 by ASCII, 50=0 PVHUE DOWN<CR>
HUE ** --- DVP-602CI can be operated from -6 to +6(44 to 56) PVHUE 50<CR>
HUE ? Return PVHUE Status PVHUE ?<CR>
DNR OFF DNR direct change PVDNR OFF<CR>
DNR LOW PVDNR LOW<CR>
DNR MID PVDNR MID<CR>
DNR HI PVHUE HI<CR>
DNR ? Return PVDNR Status PVDNR ?<CR>
ENH UP ENHANCER UP/DOWN, direct change to **dB PVENH UP<CR>
ENH DOWN **:00 to 12 by ASCII, 00=0 PVENH DOWN<CR>
ENH ** --- DVP-602CI can be operated from 0 to 12 PVENH 12<CR>
ENH ? Return PVENH Status PVENH ?<CR>
SH UP SHARPNESS UP/DOWN, direct change to **dB PVSH UP<CR>
SH DOWN **:44 to 56 by ASCII, 50=0 PVSH DOWN<CR>
SH ** --- DVP-602CI can be operated from -6 to +6(44 to 56) PVSH 50<CR>
SH ? Return PVSH Status PVSH ?<CR>
PV COMMAND : "*" parameter uses two ASCII characters. (see page 6 J) section)

V.5.6.0
- 10 -
※Cursor/Enter/Setup/Parameter
COMMAND PARAMETER function example
MN CUP “Cursor Up” Control MNCUP<CR>
CDN “Cursor Down” Control MNCDN<CR>
CLT “Cursor Left” Control MNCLT<CR>
CRT “Cursor Right” Control MNCRT<CR>
ENT “Enter” Control MNENT<CR>
RTN “RETURN” Control MNRTN<CR>
MEN ON “GUI Menu ON” Control MNMEN ON<CR>
MEN OFF “GUI Menu OFF” Control MNMEN OFF<CR>
※Remote Lock/Panel Lock
COMMAND PARAMETER function example
SY REMOTE LOCK ON REMOTE CONTROL LOCK ON/OFF SYREMOTE LOCK ON<CR>
REMOTE LOCK OFF SYREMOTE LOCK OFF<CR>
REMOTE LOCK ? Request SYREMOTE LOCK Status SYREMOTE LOCK ?<CR>
PANEL LOCK ON PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON SYPANEL LOCK ON<CR>
PANEL LOCK ? Request SYPANEL LOCK Status SYPANEL LOCK ?<CR>