DentalEZ Forest User manual

INSTALLATION
INSTRUCTIONS
2.17.21 0097-305 Rev. T 4 of 4
6200 NE Cherry Drive, Hillsboro, OR 97124 USA (TF) 800 . 423 . 3555 (T) 503 . 640 . 3012 (F) 503 . 693 . 9715
DTE OREGON, INC. DENTALEZ.COM
REAR PIVOT MOUNT
1 of 4
ALERT SYMBOL KEY
The safety notices associated with the following should be
given special attention when they appear in maintenance,
operating and emergency procedures in the guide.
WARNING indicates that the personal safety of the
patient, end user or technician could be compromised
by disregarding the WARNING. Not following instruc-
tions may result in an injury.
CAUTION indicates that a particular procedure
or precaution must be followed to avoid system
irregularity or possible damage to the product.
NOTE indicates special information to improve the
ease of maintaining the product, or to clarify important
information.
CAUTION: To avoid electrostatic discharge (ESD)
damage to electronics, always wear grounded wrist
strap attached to a ground adapter (eg: Banana or
Grounding plug) when handling circuit boards, chair
controls, and cables or working in the area of electrical
circuits.
CAUTION: Field modifications that alter the electrical
and/or mechanical safety of Forest products conflict
with agency construction file requirements and are not
sanctioned by Forest.
NOTE: Installation Verification: Refer to Operator’s
Guide or Service Manual on our website at Forest-
dental.com; perform all operations. If operations
performing as intended installation complete. If
operations not performing as intended, review steps in
installation instructions to confirm correct installation or
call Forest Technical Support at 800-423-3555.
FIG.1: POSITION CHAIR
Tools Required: 1/8”, 5/32”, 3/16”, 3/32” & 5/16”, 3mm, 8mm, and
10mm, Allen Hex Wrenches, 1/8”, 5/16” Allen Sockets with
Torque Wrench, 3/4”, 9/16” & 15/16” Wrench, Flathead Screw-
driver, and Nitrile Gloves.
NOTE: Chairs purchased before July of 2014 contain
metric screws, all chairs purchased after this date
contain standard screws. This kit contains a metric and
standard nut and bolt set to accommodate either chair.
Please check to make sure that you are using the
correct tools and hardware for your chair before
proceeding.
NOTE: If rear pivot is already installed, proceed to page 3.
REAR PIVOT ASSISTANT’S OR CUSPIDOR
MOUNT 3900 CHAIR
STEP 1: Position the chair’s back in the fully up position and
the base in the fully down position. (FIG. 1)
STEP 2: Remove the 6 screws holding the upholstery in place
(Phillips screwdriver). Sit upholstery and hardware aside.
(FIG. 2)
FIG. 2: REMOVE SEAT UPHOLSTERY
ROUTING DRAIN/SUCTION LINE
STEP 1: Remove covers. (FIG. 1)
STEP 2: Route and secure tubings together with zip tie. (FIG. 2)
CAUTION: Do not kink tubings with zip tie.
STEP 3: Make appropriate connection at utility center.
STEP 4: Reinstall covers.
STEP 5: Reinstall upholstery if originally removed.
FIG. 1: REMOVE COVERS.
COVERS
DRAIN LINE FROM
REAR PIVOT UNIT
ZIP TIE
TUBINGS
TOGETHER
FIG. 2: REAR UNIT DRAIN/SUCTION LINE.
6

2 of 4 3 of 4
REAR PIVOT ASSISTANT’S OR CUSPIDOR
MOUNT 3900 CHAIR (CONTINUED)
LIFT COVER PLATE INSTALLATION (FIG. 3)
STEP 1: Remove existing lift cover plate from chair (1/8” or
3mm hex).
STEP 2: Use pre-existing screws to install the new cover plate
that contains the umbilical routing hole.
REAR PIVOT MOUNT SETUP (FIG. 4)
STEP 1: Install rear pivot bumpers on the mounting plate using
the screws provided (5/32” hex). Choose hole location based
on the desired limits of the link arm that will be attached.
REAR PIVOT MOUNT INSTALLATION (FIG. 5)
STEP 1: Remove 3 shoulder bolts as shown (3/8” or 10mm hex)
If a chair mounted touchpad is installed, remove it during this
step.
STEP 2: Install mounting plate and spacers with nuts and
bolts provided. (5/16” hex & 3/4” socket or 8mm hex & 19mm
socket). If re/installing a chair mounted touchpad, insert the
touchpad mount assembly in place of the provided spacer.
STEP 3: Remove remaining shoulder bolt. Insert spacer and
secure with nut and bolt (5/16” hex & 3/4” socket or 8mm hex
& 19mm socket).
FIG. 3:
STEP 1: REMOVE
BOLTS (3)
STEP 2: INSTALL SPACERS/BOLTS
(3)
REAR PIVOT BEARING ASSEMBLY - ASSISTANT’S
1090/1091/1095/1096/1290
REAR PIVOT BEARING ASSEMBLY - CUSPIDOR OR DUO CONTROL
1490/1495PI/1500PI/1580/1590/1591
CAUTION: Protect work area. Threads to be
sealed must be clean and dry. Shake the product
applicator before use.
FIG. 4:
FIG. 5:
CAUTION: Protect work area. Threads to be sealed
must be clean and dry. Shake the product applicator
before use.
(REAR ADAPTER)
MAIN BEARINGS
1115-314
GREASE
BEARINGS
(LINK 1110-625)
LOCTITE®
(243/242) P/N:
0030-010
(ARM SIDE )
INTERMEDIATE BEARINGS
0010-679
MODEL 3900
CHAIR
ASSISTANT’S UNIT
(LINK = 1110-911)
(REAR ADAPTER)
MAIN BEARINGS
1115-314
MODEL 3900
CHAIR
GREASE
BEARINGS
LOCTITE®
(243/242) P/N:
0030-010
(ARM SIDE )
INTERMEDIATE BEARINGS
0010-728
CAUTION: 2 or 3 screw threads from bolt (1) should
protrude below the nut (13) for proper installation.
CAUTION: 2 or 3 screw threads from bolt (1) should
protrude below the nut (13) for proper installation.
STEP 3: REMOVE BOLT; INSTALL
SPACER/BOLT (1) CUSPIDOR OR
DUO CONTROL
LOCTITE®
(243/242) P/N:
0030-010