DentalEZ Star TITAN 3 5K MOTOR User manual

CONTENTS SPECIFICATIONS
5,000 RPM MOTOR: Titan 3 (StarDental Part #262261); Titan 3 For use with
Extended Straight Attachment (ESA) (StarDental Part
#265208); Titan 3 Fixed Back End (StarDental Part #262409);
or Titan T (StarDental Part #263940)
20,000 RPM MOTOR: Titan 3 (StarDental Part #262262); Titan 3 Fixed Back End
(StarDental Part 262410); or Titan T (StarDental Part #263941)
• No Lubrication Required
• Recommended Air Pressure: 40-45 psi (swivel motor)
• Air Flow: 2.1 SCFM @ 40-45 psi at Maximum Power Point (swivel motor)
• Rotation: Forward and Reverse
• 4-Line Connection (Fixed Back End)
INSTALLATION - SWIVEL MOTORS
1. Select the motor appropriate for tubing based on power requirements (see FIG.1). Examine connection of the
motor and swivel tubing configuration as these must match configuration of delivery system tubing (see FIG. 2).
DRIVE AIR WATER
EXHAUST AIR AIR
4-LINE TUBING 2/3-LINE TUBING
DRIVE AIR
WATER
SWIVEL
BEARING ASSEMBLY
ISO CONNECTOR
TUBING
COUPLER
TUBING
WRENCH
TUBING
COUPLER TURN COUPLER WHILE HOLDING
SWIVEL IN PLACE
OPERATION
The 120° rotation speed adjustment ring sets direction and speed. To run motor forward at full speed, rotate ring
towards the letter ‘F’ while operating the foot control. Rotate to the letter ‘R’ to yield full speed in reverse. Vary speed
by rotating ring in either direction towards center. Note the small depression for the current setting. After setting, the
motor runs at current speed and direction until reset. Pausing the motor is not needed to alter direction or speed
using the ring. (see FIG.6)
20,000 rpm - Lube Free
Made in the U.S.A.
JXXXXX
®
Titan3
StarDental
®
SMALL DEPRESSION
120° ROTATION SPEED
ADJUSTMENT RING
®
Titan3
5,000 rpm - Lube Free
Made in the U.S. A.
JXXXXX
StarDental
®
Titan3
20,000 rpm - Lube Free
Made in the U.S.A.
JXXXXX
®
Star Dental
®
5K MOTOR
20K Motor
SWIVEL
DRIVE GEAR
INSTALLATION - NON SWIVEL MOTORS
NOTE: If delivery unit has oil/mist lubrication, detach and drain; motor needs no lubrication.
NOTICE To prevent damage to bearings, before installing always check drive air pressure by using
air pressure gauge, (4/6-Line) between motor and tubing and obtain a reading. Adjust air pressure at
delivery head until gauge reads 40-45 psi while operating motor in full forward position and with foot
control completely depressed.
1. Examine rear end connector of motor(FIG.5). Verify motor matches tubing connector of delivery system.
2. To connect motor to tubing, align drive air and exhaust tubes with mating ISO connector holes in
coupler.
3. While applying slight pressure to hold tubing in connector holes, slide tubing coupler forward and
engage threads. Continue threading tubing coupler clockwise until hand tight against the motor.
DO NOT OVER TIGHTEN.
NOTE: This joint loosens over time, resulting in air leakage and loss of power. Check for tightness
periodically.
®
Titan3
5,000 rpm - Lube Free
Made in the U.S.A.
JXXXXX
StarDental
®
Titan 3
20,000 rpm - Lube Free
Made inthe U.S.A.
JXXXXX
R
StarDental
Instruments
®
DIRECTION & SPEED
CONTROL RING
DRIVE
GEAR
REAR END CONNECTOR
5K MOTOR
(STARDENTAL PART #262409)
DRIVE
GEAR
20K MOTOR
(STARDENTAL PART #262410)
STERILIZABLE UP TO 135°C
135°C
INDICATIONS FOR USE
Before operating the handpiece, carefully read and follow all of these instructions. Save these
instructions for future reference and observe all warnings and cautions.
The Titan®5K and 20K low-speed dental motors are used by trained dental professionals to facilitate
various dental procedures requiring cutting, drilling, polishing and pin setting.
Note: If delivery unit has oil/mist lubrication, detach and drain; motor needs no lubrication.
NOTICE To prevent damage to bearings, before installing always check drive air pressure by using
air pressure gauge, (4/6-Line) between swivel and tubing and obtain a reading. Adjust air pressure at
delivery head until gauge reads 40-45 psi while operating motor in full forward position and with foot
control completely depressed.
2. Disconnect swivel from motor if necessary. Grasp the swivel in front of the bearing assembly
between the thumb and index finger as shown in FIG.3.
3. Slide tubing coupler until the end of the ISO connector is exposed; hold in hand as shown with
fingers securing the tubing.
4. Align and insert swivel tubes into the ISO connector holes.
5. While applying slight pressure to hold fittings in the connector holes, slide coupler forward and
engage threads. Continue threading coupler clockwise until hand tight against the swivel.
6. Using the wrench as shown in FIG.4, tighten the swivel to the tubing coupler. Be sure to turn tubing
coupler, not swivel. DO NOT OVER TIGHTEN.
Note: This joint loosens over time, resulting in air leakage and loss of power. Check for tightness
periodically.
7. Connect motor to swivel.
CLEANING & STERILIZATION
6WDU 7LWDQ 
USP/XEH)UHH
0DGHLQWKH86$
-;;;;;
5
5
StarDental® Instrument Solutions
Drive Air
Red Tip
Applicator
Star Titan 3
20,000 rpm - Lube Free
Made in the U.S.A.
JXXXXX
RR
INTERNAL
SURFACES
SWIVEL BEARING/
SPRING ASSEMBLY
CLEAN
062283 Rev Q Date of Issue 2023-01-30 ©2023 DENTALEZ, Inc.
TITAN LOW-SPEED MOTOR
SPECIFICATIONS
INSTALLATION - SWIVEL
MOTORS
INSTALLATION-NON
SWIVEL MOTORS
OPERATION
CLEANING
STERILIZATION
APPLICATION GUIDE
TROUBLESHOOTING
REPLACEMENT PART
NUMBERS
WARRANTY
FIG. 1 FIG. 2
FIG. 3
Caution:U.S.Federal law restricts this device to sale by or on the order of a licensed physician.
FIG. 4
FIG. 5
FIG. 6
CAUTION It is the responsibility of the user to use only FDA compliant sterilizing equipment and
accessories that are capable of meeting the manufacturers recommendations below.
CAUTION Do not exceed 135°C
Do not use: • dry heat sterilizer • cold sterilizers • ultrasonic cleaners • hand soaps
• surface sprays • surface wipes • chemical disinfectors
• surgical milk • detergents • immersion techniques
• sterilizer bags containing disinfectants
LIMITS ON REPROCESSING Repeated processing has minimal effect on these attachments. End of life is normally
determined by wear and damage due to use.
INSTRUCTIONS
WARNING The handpiece motor must be cleaned and sterilized before first use and between patient use.
CONTAINMENT AND
TRANSPORTATION:
It is recommended that handpieces are reprocessed as soon as is reasonably practical
following use.
PREPARATION FOR
CLEANING:
Remove motor from swivel if applicable or tubing.
CLEANING - AUTOMATED: Washer-disinfectors are not recommended.
CLEANING - MANUAL: Cleaning the Swivel &Mating Motor Part: (FIG.7)
To optimize operation of the swivel connector,
clean all internal surfaces of the motor with
a cotton swab soaked in isopropyl alcohol
until clean. Clean area around bearing/spring
assembly at rear of swivel using isopropyl
alcohol and a toothbrush.
Dry both using syringe air.
Sterilizing Handpiece Motor: After each patient,
flush air by running handpiece motor for 20
seconds. Remove attachment. Clean all internal surfaces at rear of handpiece motor with a cotton
swab soaked in isopropyl alcohol until clean. Clean all external surfaces using a small toothbrush
with isopropyl alcohol. Dry thoroughly. Place handpiece motor and swivel in sterilization bag – .
Follow the sterilization guidelines as stated by the manufacturer of your sterilizer.
LUBRICATION: The Titan Motor is LubeFree and therefore requires
no lubrication. However at times debris from the
delivery system's drive air tubing collects in the
motor. This build-up may cause sluggish motor
operation. To ease, place 3 drops of DentaLube II,
StarDental Part #262539 into the drive air tube of
motor, and alternately operate the motor in forward
and reverse (see FIG 8).
Motor should be routinely maintained, checked for corrosion, worn parts, etc. and should be replaced
on an as needed basis.
DISINFECTION: Use steam sterilization exclusively for complete sterility as outlined below.
MAINTENANCE: See "Lubrication" Section.
INSPECTION & FUNCTION
TESTING:
See Installation, Operating Recommendations, and/or Troubleshooting sections of this
manual.
PACKAGING: Single: A standard sterilization packaging material must be used. Ensure that the pack is
large enough to contain the item without stressing the seals.
WRAPPED INSTRUMENT
STERILIZATION:
Gravity Type Autoclave: Pre-Vacuum Autoclave:
• Minimum of 15 minutes at 132° C • Minimum of 4 minutes at 132° C
• Minimum of 30 minutes at 121° C
Do not exceed 135° C
FIG. 7
FIG. 8
DENTALEZ, Inc., StarDental ®Division
1816 Colonial Village Lane Lancaster, PA 17601 USA
NON-STERILE
MD
TITAN 3 5K MOTOR TITAN 3 20K MOTOR TITAN 3 5K MOTOR FIXED BACKEND TITAN 3 20K MOTOR FIXED BACKEND TITAN T 5K MOTOR TITAN T 20K MOTOR

TROUBLESHOOTING
PROBLEM: LACK OF POWER
CAUSE: Air pressure
CORRECTION: Verify proper motor air pressure. Refer to applicable Installation section.
CAUSE: Crimped tubing
CORRECTION: Straighten tubing inside and outside delivery head.
CAUSE: Swivel or Fixed Back End Motor not threaded fully onto tubing
CORRECTION: Refer to applicable Installation section.
CAUSE: Brittle swivel or Fixed Back End Motor silicone rubber seal
CORRECTION: Replace silicone rubber seal for 2/3-line swivel with StarDental®Part #203103
and 4-line with StarDental Part #202897.
CAUSE: SWIVEL O-RINGS WORN
CORRECTION: Replace swivel O-rings, StarDental Part #259884.
CAUSE: Debris build-up in motor or attachment
CORRECTION: Clean motor and attachment. Refer to Cleaning section in this manual and ap-
plicable attachment's manual(s).
PROBLEM: SWIVEL WILL NOT DISENGAGE FROM MOTOR
CAUSE: Build-up of debris
CORRECTION: Place 3 drops of DentaLube II, StarDental Part #262539, into the swivel/tubing
connector. Rotate swivel to circulate lubricant. Disengage motor. Contact dealer if
unable to disengage swivel. To prevent reoccurrence, refer to Cleaning.
Straight Nose Cone .............................................................................. 257506......................................263942
Motor-to-Angle Adapter......................................................................... 264073......................................263970
Torque Multiplier ................................................................................... 258443......................................263944
Swivel, Motor 2/3-Line .......................................................................... 260152 ...................................... 260152
Swivel, Motor 4-Line ............................................................................. 260144 ...................................... 260144
LubeFree Ball Bearing Auto Latch Angle .............................................. 264146
LubeFree Ball Bearing Manual Latch Angle ......................................... 262738
LubeFree Ball Bearing Autochuck Friction Grip Angle.......................... 264151
LubeFree 5 Star Prophy Angle.............................................................. 265801
Ball Bearing Auto Latch Angle .............................................................. 264182
Ball Bearing Manual Latch.................................................................... 259005
Ball Bearing Autochuck Friction Grip Angle .......................................... 264149
Silicone Rubber Seal, 2/3-Line (Pkg. of 3)............................................ 203103 ......................................203103
Silicone Rubber Seal, 4-Line (Pkg. of 3)............................................... 202897......................................202897
Swivel O-Rings Kit (2 large, 2 small) .................................................... 259884......................................259884
DentaLube II ......................................................................................... 262539......................................262539
Titan T 20K, 4 Line, Stainless Steel Back End, Motor .............................................................................264430
Titan 3 5K Motor - Used with Extended Straight Attachment (ESA) ..... 265208
NOTE: If a problem persists, contact dealer for further assistance or contact StarDental technical service at
1-866-DTE-INFO.
Lubricated LubeFree Lubricated LubeFree
ENDODONTIC (Condensing gutta percha)
RPM Range: 10,000 to 20,000
Systems Configuration Options:
20,000 RPM Motor 262262 263941
Motor-to-Angle Adapter 264073 263970
Ball Bearing Latch Angle OR 259005 262738
Ball Bearing Auto Latch Angle 264182 264146 263949
CARIES REMOVAL
Systems Configuration Options:
5,000 RPM Motor 262261 263940
RPM Range: 2,000 to 5,000
Motor-to-Angle Adapter 264073 263970
Ball Bearing Friction Grip Angle OR 263955
Ball Bearing Autochuck Friction Grip Angle 264149 264151 263953
Ball Bearing Latch Angle OR 259005 262738
Ball Bearing Auto Latch Angle 264182 264146 263949
20,000 RPM Motor 262262 263941
RPM Range: 2,000 to 5,000
Torque Multiplier 258443 263944
Motor-to-Angle Adapter 264073 263970
Ball Bearing Friction Grip Angle OR 263955
Ball Bearing Autochuck Friction Grip Angle 264149 264151 263953
Ball Bearing Latch Angle OR 259005 262738
Ball Bearing Auto Latch Angle 264182 264146 263949
FINISHING (Cavity and crown preps)
RPM Range: 10,000 to 20,000
Systems Configuration Options:
20,000 RPM Motor 262262 263941
Motor-to-Angle Adapter 264073 263970
Ball Bearing Friction Grip Angle OR 263955
Ball Bearing Autochuck Friction Grip Angle 264149 264151 263953
Ball Bearing Latch Angle OR 259005 262738
Ball Bearing Auto Latch Angle 264182 264146 263949
POLISHING
(Amalgam, composites, gold margins)
RPM Range: 10,000 to 20,000
Systems Configuration Options:
20,000 RPM Motor 262262 263941
Motor-to-Angle Adapter 264073 263970
Ball Bearing Latch Angle OR 259005 262738
Ball Bearing Auto Latch Angle 264182 264146 263949
APPLICATION GUIDE TITAN3 TITAN T
PROPHY Lubricated LubeFree Lubricated LubeFree
RPM Range: 1,000 to 3,000
Systems Configuration Options:
5,000 RPM Motor 262261 263940
Motor-to-Angle Adapter 264073 263970
5 Star Prophy Angle 265803 265801 265802
20,000 RPM Motor 262262 263941
Torque Multiplier 258443 263944
Motor-to-Angle Adapter 264073 263970
5 Star Prophy Angle 265803 265801 265802
GRINDING & TRIMMING (Fabrication)
RPM Range: 10,000 to 20,000
Systems Configuration Options:
20,000 RPM Motor 262262 263941
Straight Nose Cone 257506 263942
POST & PIN DRILLING
Systems Configuration Options:
5,000 RPM Motor 262261 263940
RPM Range: 1,000 to 5,000
Motor-to-Angle Adapter 264073 263970
Ball Bearing Latch Angle OR 259005 262738
Ball Bearing Auto Latch Angle 264182 264146 263949
20,000 RPM Motor 262262 263941
RPM Range: 1,000 to 5,000
Torque Multiplier 258443 263944
Motor-to-Angle Adapter 264073 263970
Ball Bearing Latch Angle OR 259005 262738
Ball Bearing Auto Latch Angle 264182 264146 263949
PIN SETTING
Systems Configuration Options:
5,000 RPM Motor 262261 263940
RPM Range: 1,000 to 5,000
Motor-to-Angle Adapter 264073 263970
Ball Bearing Latch Angle OR 259005 262738
Ball Bearing Auto Latch Angle 264182 264146 263949
20,000 RPM Motor 262262 263941
RPM Range: 500 to 2,000
Motor-to-Angle Adapter 264073 263970
10:1 Gear Reduction Latch Angle 264180 263951
20,000 RPM Motor 262262 263941
RPM Range: 500
Torque Multiplier 258443 263944
Motor-to-Angle Adapter 264073 263970
10:1 Gear Reduction Latch Angle 264180 263951
ENDODONTIC (Canal enlargements)
Systems Configuration Options:
20,000 RPM Motor 262262 263941
RPM Range: 500 to 2,000
Motor-to-Angle Adapter 264073 263970
10:1 Gear Reduction Latch Angle 264180 263951
5,000 RPM Motor 262261 263940
RPM Range: 350 to 5,000
Motor-to-Angle Adapter 264073 263970
Auto Latch Endodontic Angle -
-for Standard Files & Reamers
(90° reciprocating motion) OR
Manual Latch Endodontic Angle -
-for Latch Type Files & Reamers
(90° reciprocating motion)
DRYING: Dry the motor for 30 minutes minimum using the sterilization dry cycle and allow the motor
to cool to room temperature in bag prior to use. If moisture is present, increase your sterilizer
dry cycle appropriately.
STORAGE: Store in bag after sterilization until ready to use.
ADDITIONAL
INFORMATION:
Do not exceed the sterilizer manufacturer’s guidelines for load capacity. Use only paper or
paper/plastic bags.
MANUFACTURER CONTACT: See first or last panels of this manual.
CLEANING & STERILIZATION, CONTINUED APPLICATION GUIDE, TITAN3 TITAN T
CONTINUED
REPLACEMENT PART NUMBERS
ALWAYS INSIST ON STARDENTAL PARTS FOR BEST PERFORMANCE.
DESCRIPTION
TITAN T
ITEM NUMBER
TITAN 3
ITEM NUMBER
LIMITED WARRANTY
O-Rings and Seals are specifically excluded from this warranty.
DENTALEZ warrants the Titan Low-Speed Handpiece Motor for 1 year from the date of purchase*.
Please note the following additional terms of our warranty policy:
• Warranty covers manufacturing defects only and does not cover defects resulting from abuse, accidents, misuse, improper handling, cleaning,
care or maintenance or the failure to follow or observe our operating/use, maintenance and/or installation instructions. Damage resulting from
the use of chemicals, cleaners, disinfectants or sterilization is not covered under this warranty nor is normal wear and tear. Failure to use
authorized parts or an authorized repair facility voids this warranty.
• Liability is limited to repair or replacement of the defective part(s) or products at our sole discretion. All other liabilities, in particular liability for
damages, including, without limitation, special, exemplary, consequential or incidental damages are excluded
• THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. NO EMPLOYEE, REPRESENTATIVE OR DEALER IS AUTHORIZED
TO CHANGE THIS WARRANTY IN ANY WAY OR TO GRANT ANY OTHER WARRANTY.
*Provided conditions in warranty are met.
WARRANTY REGISTRATION
Please visit the website below to register your StarDental product. This will ensure proper registration and prompt and accurate service should any
of your purchases need evaluation or repair during the warranty period.
StarDental Products: WWW.DENTALEZ.COM/warranty
FOR NEW PRODUCTS, MANUALS AND TECHNICAL INFORMATION, CALL
1-866-DTE-INFO OR VISIT OUR WEB SITE @ WWW.DENTALEZ.COM
IMPORTANT NOTICE ABOUT RETURNING PRODUCT TO DENTALEZ INC.
Anyone wishing to return any DENTALEZ Inc. product to a DentalEZ facility MUST obtain the proper RETURN AUTHORIZATION NUMBER from the
Customer Service Department. The RA Number must appear clearly marked on both the outside and inside of the returned product carton. When
calling for a return authorization number you will be asked to provide the following information:
To Obtain A
Return Authorization
Number Call
1-866-DTE-INFO
1. Product Name, Model Number or Part Number
2. Serial Number of Product
3. Dealer Return Purchase Order Number
4. Reason For Return
5. Copy of Invoice Showing Purchase
Items will be evaluated. Return Authorization Number is not a guarantee for credit. Your cooperation with this procedure will help us expedite
processing of any returns.