Dentsply Sirona Gutta-Smart User manual

Gutta-Smart™
Getting Started Guide

2
1
Package contents
Flow Handpiece
Base Station
Gutta-Percha
Cartridges
(GP)
20 Ga cartridges (10)
23 Ga cartridges (10)
25 Ga cartridges (10)*
*purchased separately
Pack Handpiece
A C
G I
COLOR AND MATERIALS
JULY 24, 2017
REF AEU-65
SN EN19000719-001
REF AEU-65
SN
EN19000719-001
COLOR AND MATERIALS
JULY 24, 2017
GP
REF AEU-65
SN EN19000719-001
REF AEU-65
SN
EN19000719-001
REF AEU-65
SN EN19000719-001
REF AEU-65
SN
EN19000719-001
Getting
Started
Guide
Directions
For
Use
Thermal Response Tip*
(TRT)
*(purchased separately)
Electric Heat Pluggers
(EHP)
Flow Handpiece
Front-end Sealing Cap
Pack Handpiece
Front-end Sealing Cap
Flow Heater
(HTR)
Cannula Bending Tool
Power Adapter
(100–240V, 50–60Hz)
Plug Adapters
(used with
Power Adapter)
COLOR AND MATERIALS
JULY 24, 2017
REF AEU-65
SN EN19000719-001
REF AEU-65
SN
EN19000719-001
Small Medium Large
40/. 02 5 50/.05 6 0/. 0 6

Gutta Smart™ Getting Started Guide 3
The electric heat pluggers, ow heaters and thermal response tips must be cleaned,
disinfected and sterilized before each usage to prevent any contamination. This concerns
the rst use, as well as all subsequent uses. Refer to the Directions For Use for required
sterilization instructions. The base station and handpieces must also be cleaned and
disinfected before each usage. The use of custom front-end sealing caps are required for
wipe-down disinfection of the handpieces. Prior to using a GP cartridge on a patient, wipe
the cannula with isopropyl alcohol and allow to dry.
Handpieces
AInsert the front-end sealing caps rmly onto the ends of
the pack and ow handpieces.
COLOR AND MATERIALS JULY 24, 2017
GP
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
COLOR AND MATERIALS JULY 24, 2017
GP
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
COLOR AND MATERIALS JULY 24, 2017
GP
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
BClean the exterior of the handpieces with a soft cloth
moistened with a mild non-chlorinated detergent or
disinfecting solution.
Base Station
AClean the exterior of the base station with a soft cloth
moistened with a mild non-chlorinated detergent or
disinfecting solution.
!
Do not spray cleaning
solutions directly on the
handpieces.
!
Do not spray cleaning
solutions directly on the
base station.
2
Disinfection & cleaning

4
Before Use – System Setup
APlug the cord from the power adapter into the
socket on the back of the base station.
BPlace both handpieces into the base station
Allow to charge until the green LEDs on the handpieces
stop ashing, indicating a full charge. Either handpiece
can be placed into either side of the base station.
Attaching Electric Heat Plugger (EHP) to Pack Handpiece
ASelect one of the three EHPs provided
Size small, medium, or large
BSeat the EHP
Push the EHP into the end of the pack handpiece until it
seats rmly.
COLOR AND MATERIALS JULY 24, 2017
GP
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
CAfter use, remove the EHP
To remove the EHP, wait for it to cool down, then pull
straight out from handpiece.
Attaching Thermal Response Tip (TRT) to Pack Handpiece
AConnect the TRT
Push the TRT into the end of the pack handpiece
until it seats rmly.
COLOR AND MATERIALS JULY 24, 2017
GP
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
!
EHPs can be
installed in any one
of 4 orientations.
!
The pack handpiece
temperature must be
set to 90°C when using
the TRT to prevent
overheating and
patient injury.
3
Handpiece set-up

Gutta Smart™ Getting Started Guide 5
BAfter use, remove the TRT
To remove the TRT, wait for it to cool down, then pull
straight out from handpiece.
COLOR AND MATERIALS JULY 24, 2017
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
Attaching Heater (and GP cartridge) to Flow Handpiece
ASelect a gutta-percha (GP) cartridge
20, 23, or 25 gauge
BInsert the GP cartridge through the heater
COLOR AND MATERIALS JULY 24, 2017
GP
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
CThread the heater with the GP cartridge onto
the ow handpiece
COLOR AND MATERIALS JULY 24, 2017
GP
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
COLOR AND MATERIALS JULY 24, 2017
GP
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
COLOR AND MATERIALS JULY 24, 2017
GP
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
REF
AEU-65
SN
EN19000719-001
DBend the cannula
Bend the cannula to the desired angle using the cannula
bending tool.
ERemove after use
To remove the heater, wait for it to cool down, then
unscrew it from the ow handpiece. The GP push-rod will
automatically retract.
!
Using anything other
than the cannula
bending tool to curve
the cannula can result
in cartridge rupture or
handpiece damage.
Repeated bending can
damage the cannula.

6
Pack Handpiece Features
Electric Heat Plugger (EHP)
or
Thermal Response Tip (TRT)
Cu switch
EHP mode Temperature setting 100°-400°C.
Press and hold the raised ridge on the cu switch to heat the
EHP. The heater will automatically turn o after 10 seconds of
continuous heating. Release and press the cu switch again to
continue heating.
TRT mode Temperature setting 90°C.
Press and hold the raised ridge on the cu switch to heat the
TRT. The heater will automatically turn o after 60 seconds of
continuous heating. Release and press the cu switch again to
continue heating.
Heater indicator
Blue: Heater is on (cu switch is depressed).
Audible tone option
High-frequency tone: Heating up
Low-frequency tone: Set temperature reached and maintained
Bluetooth indicator
Flashing blue: Searching for connection
Blue: Bluetooth connection established
Flashing yellow: Connection lost
Battery level indicator
Green: Battery full
Flashing Green: Battery charging
Red: Battery low
Flashing Red: Battery very low. Charge immediately.
4
Features

Gutta Smart™ Getting Started Guide 7
Flow Handpiece Features
Heater (HTR)
Removing the HTR initiates GP push-rod retraction.
Cu Switch
Press the raised ridge on the cu switch to initiate heating, if
not already at set temperature. Heating takes approximately 90
seconds. The heater will turn o after 10 minutes of inactivity
to conserve battery power.
With HTR at set temperature, press and hold to extrude GP.
With no HTR installed, press to interrupt GP push-rod
retraction. Each additional press alternates the push-rod
direction, if necessary for cleaning.
GP push-rod direction indicator
Blue: GP push-rod moving forward
Flashing blue: GP push-rod retracting
Gutta-percha level indicator
Green: Full
Yellow: Low
Red: Critically low/empty
Heater status indicator
White light o: Heater o
Flashing white: Heating up
White: Set temperature reached and maintained
Bluetooth indicator
(see pack handpiece for more details)
Battery level indicator
(see pack handpiece for more details)

8
Programming the Pack Handpiece
APress the screen directly below
the pack handpiece
to access the pack settings.
BPress the temperature segment
on the touch-screen
to adjust the pack temperature
(100°–400°C) using the 
buttons that appear. Press the
temperature segment again to
exit the adjustment screen.
CPress the tone segment on the
touch-screen
to adjust the tone volume
(0%–100%) using the 
buttons that appear. Press the
tone segment again to exit the
adjustment screen.
DIf performing a thermal
response test
press the temperature segment
on the touch-screen to adjust the
pack temperature to 90°C using
the  buttons that appear.
Press the temperature segment
again to exit the adjustment
screen.
Electric Heat Plugger
mode
!
Setting the pack
temperature to
100°-400°C
automatically activates
the electric heat plugger
mode.
Thermal response mode
!
The pack temperature
must be set to 90°C to
activate the thermal
response tip mode.
5
Programming

Gutta Smart™ Getting Started Guide 9
Programming the Flow Handpiece
APress the screen directly below
the ow handpiece
to access the ow settings.
BPress the temperature segment
on the touch-screen
to adjust the ow temperature
(130°–160°C) using the 
buttons that appear. Press the
temperature segment again to
exit the adjustment screen.
CPress the ow rate segment
on the touch-screen
to adjust the ow rate (20%–
100%) using the  buttons
that appear. Press the ow
rate segment again to exit the
adjustment screen.

10
Operating the Pack Handpiece
APress the power button
to turn on the handpiece.
BPress and hold the raised ridge on
the cu switch on the pack handpiece
to heat the electric heat plugger.
You will hear a high-frequency tone
while the tip is heating, then a
low-frequency tone once the set
temperature is reached. The heater will
automatically shut o after 10 seconds
of continuous heating. Release and
press the cu switch again to continue
heating if the heat cycle times out. The
blue indicator ring illuminates while the
heater is on (while cu switch is
depressed).
CPress and hold the raised ridge on
the cu switch on the pack handpiece
to heat the thermal response tip.
You will hear a high-frequency
tone while the tip is heating, then
a low-frequency tone once the set
temperature is reached. The heater will
automatically shut o after 60 seconds
of continuous heating. Release and
press the cu switch again to continue
heating if the heat cycle times out. The
blue indicator ring illuminates while
the heater is on (while cu switch is
depressed).
!
Disinfect the handpiece
and sterilize electric heat
pluggers and thermal
response tip before
starting a procedure.
Electric heat plugger
mode
!
If the tone volume is
set to 0%, no tone will
be audible to indicate
the tip is heating up
or maintaining the set
temperature.
Thermal response mode
!
The pack temperature
must be set to 90°C to
activate the thermal
response tip mode.
!
Place gutta-percha on
the tip of the thermal
response tip before
applying to the patient’s
tooth.
6
Operation