Safety Information
06/2021 5 / 268
Model LpA LWA
EFD43-45 < 70 < 80
EFD51-70 < 70 < 80
EFD51-135 < 70 < 80
EFD60-175 < 70 < 80
EFD60-250 < 70 < 80
EFD80-330 < 70 < 80
EFD80-450 < 70 < 80
EFD80-680 < 70 < 80
EFD80-950 < 72 < 83
EFDO24-20 < 70 < 80
EFDO30-80 < 70 < 80
EFDO40-180 < 72 < 83
EFDO54-450 < 70 < 80
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. The vibration emis-
sion level may be used for a preliminary assessment of expo-
sure. These declared values are not adequate for use in risk
assessments and values measured in individual work places
may be higher. The actual exposure values and risk of harm
experienced by an individual user are unique and depend
upon the way the user works, the workpiece and the worksta-
tion design, as well upon the exposure time and the physical
condition of the user.
We, Ets Georges Renault, cannot be held liable for the con-
sequences of using the declared values, instead of values re-
flecting the actual exposure, in an individual risk assessment
in a work place situation over which we have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing http://
www.pneurop.eu/index.php and selecting 'Tools' then 'Legis-
lation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
WEEE
Information concerning Waste of Electrical and Electronic
Equipment (WEEE):
This product and its information, meets the requirements of
the WEEE Directive (2012/19/EU), and must be handled in
compliance with the directive.
The product is marked with the following symbol:
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE Directive. The entire
product, or the WEEE parts, can be sent to your “Customer
Center” for handling.
FCC compliance Class A
This device complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the man-
ufacturer could void the user’s authority to operate this de-
vice.
Operation is subject to the following two conditions:(1) this
device may not cause harmful interference, and (2) this de-
vice must accept any interference received, including inter-
ference that may cause undesired operation.
FCC Responsible party:
Name: Mark Johnson
Position: General Manager
Address: Chicago Pneumatic Tool Company
LLC 1815 Clubhouse Road Rock Hill
SC 29730
USA
Mobile: +1 800 624 4735
NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device, pur-
suant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful
interference when the equipment is operated in a com-
mercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instruction man-
ual, may cause harmful interference to radio communi-
cations. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense. Any changes or modifications to this
equipment not expressly approved by Desoutter may
cause, harmful interference and void the FCC authoriza-
tion to operate this equipment.
IC compliance Class A
CAN ICS-3(A)/NMB-3(A)
(English) This device complies with Industry Canada’s li-
cence-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(French) Le présent appareil est conforme aux CNR d’Indus-
trie Canada applicables aux appareils radio exempts de li-
cence. L’exploitation est autorisée aux deux conditions suiv-
antes:
