Directed DS3+ User manual

DS3+ / DS4+ 933.TL15
v1.13.198.9
2023 Toyota RAV4 Hybrid (Smart Key)
THTON7 Compatible
(Sold Separately)

Introduction 3
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Installation 6
Wiring diagram with T-Harness (THTON7) with SLP connector 6
Wiring diagram with T-Harness (THTON7) without SLP connector 7
Wiring diagram 8
Locating components in the vehicle 9
Vehicle connections 10
Module programming 13
Module programming for convenience only (skip transponder) 14
Module programming for security-only installations 15
Pairing remotes 16
Connecting the module 16
8556T Temperature Sensor 16
8504D Combo Sensor 16
RF Systems 16
When used in conjunction with SmartStart 17
D2D port configuration 17
Manual transmission 18
LED diagnostics and troubleshooting 19
Soft reset 21
Hard reset 21
Tach learning procedure (not needed with Virtual Tach) 22
Initializing Virtual Tach (not needed with hardwired or data tach applications) 22
Limited lifetime consumer warranty 23
Quick reference guide 24
Contents

3933.TL15 1.13.198.9 2023 Toyota RAV4 Hybrid (Smart Key)
©2023 VOXX•DEI LLC. All rights reserved.
Introduction
This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a
digital configuration requires the module to be flashed with vehicle-specific firmware. Refer to our website (www.directechs.com) and click
on the DIRECTLINK text in the header for additional information.
DS3/DS3+ and DS4/DS4+ modules provide an all-in-one solution for most modern vehicles, and include remote start, keyless entry, security,
and immobilizer bypass capabilities. T-harnesses may also be used in many applications for easy installation.
The following methods are available to configure modules:
• Web: www.directechs.com (DS3/DS3+ and DS4/DS4+)
• Desktop application: Directlink DT (DS3/DS3+ and DS4/DS4+)
• Mobile device: Directlink App (DS4/DS4+ only)
When flashing via Directlink DT (desktop app) or via the Web, an XKloader2 will be required.
To configure via Web or DirectLink DT (desktop app):
1. Disconnect the main module from any (+) 12V power source.
2. Connect the module to your computer using the XKLoader2.
3. Follow the steps in the pop-up window that will be displayed when the module is detected.
Notes:
•Flashing via web is only possible using Internet Explorer on Windows 8, 8.1, and 10.
•This method is not compatible with any other browser (Edge, Chrome, Firefox, etc.).
•When using Windows 11 or newer, Directlink DT is mandatory.
The DS4/DS4+ module is designed to be configured using the DirectLink application through mobile devices.
To download the DirectLink mobile application, visit the Google Play or Apple store. They can also be
configured via Web and DirectLink DT. The DS4/DS4+ features are built in Bluetooth® 4.0, allowing you to
configure and control your system. The DS3/DS3+ module is not equipped with Bluetooth®, therefore is not
compatible with the DirectLink app for mobile devices.
To configure via DirectLink mobile app (Android/iOS):
1. Follow and complete the wiring diagram(s) related to your installation through the app.
2. When installation is complete, select Configure DS4/DS4+.
3. Follow the on-screen instructions.
FLASH REQUIRED!
FLASH REQUIRED!
4 White

4933.TL15 1.13.198.9 2023 Toyota RAV4 Hybrid (Smart Key)
©2023 VOXX•DEI LLC. All rights reserved.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.
Parking Lights Control
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Trunk / Hatch Release
Control of aftermarket alarm with OEM remote
Fuel level/EV battery level
* Odometer
Immobilizer Bypass-Data No Key Req'd
3x LOCK START (Start control using OEM Remote)
3x LOCK STOP (Stop control using OEM Remote)
Accessory Activation
Ignition Activation
RAP Shut Down (Retained ACC Power)
SmartStart
Start (Crank) Activation
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Factory Alarm Trigger Monitoring
Brake Status (foot brake)
E-Brake Status
Ignition Status

5933.TL15 1.13.198.9 2023 Toyota RAV4 Hybrid (Smart Key)
©2023 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
START HERE This section highlights important information for this specific firmware and will assist in pricing accordingly, as
well as bringing awareness to any operational or vehicle limitations.
Compatibilities and Requirements
T-Harness
compatible THTON7
AUX
Keys required for
programming 1Keys required for operation 0
Vehicle Takeover No takeover feature is available on Push-to-Start vehicles. The engine will stop when a door is open.
Firmware notes
OEM remote starter detection: If the vehicle is already equipped with an OEM remote starter, the installer must disconnect it before
installing the DS4+ otherwise it will not program. (For more information see "OEM remote starter detection")
Motorized Hatch feature: If available, the Motorized Hatch feature needs to be enabled using the configuration tool found on the
module flashing page on www.directechs.com.
Remote Start: To remote start the vehicle, all doors must be closed and locked.
Manual Transmission: For manual transmission vehicles, "Safelock" needs to be enabled for proper remote start operation.
The optional Plug & Play THTON7 T-Harness is sold separately.
Loose T-harness wires: All T-Harness wires not listed in the diagram are not required for the installation. Loose wires such as
Siren Output and Hood Input may need to be pulled from the tapped section of the T-Harness. Refer to the “Wiring diagram with
T-Harness” for more information on connections and installation instructions.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector.
Refer to the "Vehicle connections" following the installation diagram.
Footnotes
[1] Hood pin: The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin if or
not supported in Data.
[2] Siren: The siren is only required when enabling the security features during module flashing.
[3] PTS: This connection is only required for Pit Stop/ Idle mode in manual transmission vehicles or Ready mode for vehicles with hybrid
engines.
[4] SLP: Depending on the production date of your vehicle, there may not be an SLP connector at the steering column.
- Installation with SLP connector: the connection is mandatory.
- THTON7 T-Harness installation without SLP connector: you must make modifications to the T-Harness for the (12V) & (Ground). See
wiring diagram for additional information.
- Hardwire installation without SLP connector: Connection not required.
See "Locating Steering Lock Connector in Vehicle" in Vehicle connections.
[5] Security-only: For security-only installations using THTON7 T-Harness, refer to the "Locating components in the vehicle" section for
optional starter disable. Important! When flashing security-only, configure relay 3 to Starter Kill. Connect the White and
White/Brown wires to starter wire in the vehicle (No external relay required).
[6] Telematics Interrupt: Depending on the production date of your vehicle, if remote start fails, a "Telematics Interrupt" connection may
be required.

6933.TL15 1.13.198.9 2023 Toyota RAV4 Hybrid (Smart Key)
©2023 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Wiring diagram with T-Harness (THTON7) with SLP connector
AG4
(white conn. left
of body ECU)
(+) Starter:
Blue, pin 5
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
9
10
20
19
Siren
Hood Pin
(-) Push-to-Start Output: Lt. Blue/Black
(-) Hood Input: Gray
(+) Siren Output: Brown/Red
THTON7
(optional T-Harness)
12-pin Black Connector
PTS Button
(Black conn. at PTS switch)
ENGINE
START
STOP 2345
10 9 8 7 6
1
Body ECU
Connector
1
2
Headlight Switch
NOT USED
B
A
Body ECU Connector
(Lower conn. left side
of steering column)
Body ECU
(middle conn.
left side of steering column)
1
2
Cut the
Orange/Black loop.
8-pin White Connector
22-pin White Connector
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
22 812
4 2442
Slide to open
A module can also be used for
this installation.
IMPORTANT:
Position the
fuses correctly!
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
B
NOT USED
CONNECT the white
12-pin connector to
the 12-pin Red
connector labeled C.
C
(+) Starter Output: Violet/Black
Steering Lock
(black 7-pin connector)
Starter Disable (conn. side): White/Brown
Starter Disable (veh. side): White
When using a THTON7 T-harness and
flashing with security only, a Starter Disable
Connection can be made with no external relay.
Refer to the Vehicle Connections section.
Telematics
Interrupt:
Black, pin 33
Cut
Telematics Interrupt (conn. side): White/Brown
Telematics Interrupt (vehicle side): White
Do not insert 15A fuse
Do not insert 15A fuse
19
14
6
1
56
36
33
Plug 3A
(white connector rear of
dash fuse box)
(-) PTS: Gray, pin 5

7933.TL15 1.13.198.9 2023 Toyota RAV4 Hybrid (Smart Key)
©2023 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
Wiring diagram with T-Harness (THTON7) without SLP connector
AG4
(white conn. left
of body ECU)
(+) Starter:
Blue, pin 5
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
9
10
20
19
Siren
Hood Pin
(-) Push-to-Start Output: Lt. Blue/Black
(-) Hood Input: Gray
(+) Siren Output: Brown/Red
THTON7
(optional T-Harness)
12-pin Black Connector
PTS Button
(Black conn. at PTS switch)
ENGINE
START
STOP 2345
10 9 8 7 6
1
Body ECU
Connector
1
2
Headlight Switch
NOT USED
B
A
Body ECU Connector
(Lower conn. left side
of steering column)
Body ECU
(middle conn.
left side of steering column)
1
2
Cut the
Orange/Black loop.
8-pin White Connector
22-pin White Connector
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
22 812
4 2442
Slide to open
A module can also be used for
this installation.
IMPORTANT:
Position the
fuses correctly!
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
B
NOT USED
CONNECT the white
12-pin connector to
the 12-pin Red
connector labeled C.
C
(+) Starter Output: Violet/Black
Starter Disable (conn. side): White/Brown
Starter Disable (veh. side): White
When using a THTON7 T-harness and
flashing with security only, a Starter Disable
Connection can be made with no external relay.
Refer to the Vehicle Connections section.
Telematics
Interrupt:
Black, pin 33
Cut
Telematics Interrupt (conn. side): White/Brown
Telematics Interrupt (vehicle side): White
Do not insert 15A fuse
Do not insert 15A fuse
19
14
6
1
56
36
33
Plug 3A
(white connector rear of
dash fuse box)
(-) PTS: Gray, pin 5
CUT
Cut the connector.
Extend the Black wire and
connect it to a (-)Ground source.
Extend the Red wire and connect
it to a (+)12V source.
1
(+) 12V:
White, pin 1
3
Dash Fuse Box
(white conn.) NOT USED

8933.TL15 1.13.198.9 2023 Toyota RAV4 Hybrid (Smart Key)
©2023 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
SLP connection is
only required if
the connector is
present in the
vehicle.
Autolight Interrupt (conn. side): Blue/White: 1
Autolight Interrupt (vehicle side): Blue: 3
(-) Ground: Black: 10
(+) 12V Input: Red: 6 & 12
Hood Pin (-) Hood Input: Gray: 21
Siren
(+) Siren Output: Brown/Red: 11
(-) Push-to-Start Output: Lt. Blue/Black: 10
HS CAN Low: Tan: 1
HS CAN High: Tan/Black: 2
PTS Button
(Black conn. at PTS switch)
ENGINE
START
STOP 2345
10 9 8 7 6
1
(-) PTS: Gray, pin 5
(-) Lock Output: Dk. Green/Black: 3
(-) Unlock Output: Dk. Blue/Black: 9
HS CAN Low:
Violet, pin 4
HS CAN High:
Tan, pin 5
(-) Lock/Arm:
Lt. Green, pin 18
1
(+) 12V:
White, pin 1
Body ECU
Connector
3
1
2
3
Autolight:
Yellow, pin 5
(-) Unlock/Disarm: Tan, pin 17
Cut
Dash Fuse Box
(white conn.)
(+) Starter Output: Violet/Black: 8
AG4
(white conn. left
of body ECU)
(+) Starter:
Blue, pin 5
(-) SLP:Tan, pin 4
Black Steering Lock conn.
(at steering lock conn.)
(-) SLP Output: Lt. Green: 8
(-) Ground: Lt. Green/Red: 7
1
2
3
4
5
6
7
8
11
12
13
14
15
16
17
18
9
10
20
19
Body ECU Connector
(Black lower conn. left side
of steering column)
Body ECU
(Black middle conn. left side
of steering column)
Headlight Switch
(White 40-pin conn.)
678
111213
1415161718
9
10
21 20 19
12
3
45
2
678
1112131415161718 9
10
30 2122 232425262728 20
19
29
123
45
1
123456781112131415161718 9
10
313233343536
3738 30 2122
232425262728 20 19
29
3940 Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
22 812
4 2442
Slide to open
A module can also be used for
this installation.
IMPORTANT:
Position the
fuses correctly!
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
Telematics Interrupt (conn. side): White/Brown: 4
Telematics Interrupt (vehicle side): White: 5 & 11
Cut
19
14
6
1
56
36
33
Plug 3A
(white connector rear of
dash fuse box)
Telematics
Interrupt:
Black, pin 33
Do not insert 15A fuse
Do not insert 15A fuse
Wiring diagram

9933.TL15 1.13.198.9 2023 Toyota RAV4 Hybrid (Smart Key)
©2023 VOXX•DEI LLC. All rights reserved.
Locating components in the vehicle
Optional starter disable connection
22 812
4 2442
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
Refer to the
Vehicle connections
section for wire
and connector
details.
Starter Disable (connector side) : White/Brown: 4
Starter (connector side)
Starter (vehicle side)
Cut
Starter Disable (vehicle side): White: 5 & 11
Important: When flashing your module for Security Only, Relay 3 must be manually
configured to the Starter Kill function. When flashing your module for Remote Start & Security,
you must manually assign a GWA Output for starter disable.
An external relay is required.
(Applicable to CORE 194 +.)

10 933.TL15 1.13.198.9 2023 Toyota RAV4 Hybrid (Smart Key)
©2023 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2023 Toyota RAV4 Hybrid (Smart Key). Refer to “Pre-installation and application warnings” for a list of important notes.
Data harness, 8-pin white connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H1/1 Tan (Data) HS CAN Low Body ECU on dash fuse box, black 30 pin plug, pin 4 Data Violet Mandatory
H1/2 Tan/Black (Data) HS CAN High Body ECU on dash fuse box, black 30 pin plug, pin 5 Data Tan Mandatory
H1/3 Orange/Brown No Connection No Connection
H1/4 Orange/Green No Connection No Connection
H1/5 Lt. Green No Connection No Connection
H1/6 Violet/Brown No Connection No Connection
H1/7 Orange/Black No Connection No Connection
H1/8 Yellow/Black No Connection No Connection
Analog input/output harness, 22-pin white connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/1 Lt. Green/Black No Connection No Connection
H2/2 Blue/White (-) Ground When Armed (GWA) Output No Connection
H2/3 Dk. Green/Black (-) Lock Output Body ECU on dash fuse box, black 21 pin plug, pin 18 - Lt. Green (key lock) Mandatory
H2/4 Red/White No Connection No Connection
H2/5 Brown/Black (-) Horn Output Left of Dash Fuse Box, gray 18 pin plug (AG2), pin 17 - Blue Optional
H2/6 Brown/White No Connection No Connection
H2/7 White (+) No Connection No Connection
H2/8 Violet/Black (+) Starter Output Left of Dash Fuse Box, white 20 pin plug (AG4), pin 5 + Blue Remote Start
Only
H2/9 Dk. Blue/Black (-) Unlock Output Body ECU on dash fuse box, black 21 pin plug, pin 17 Doubl
e -
Tan (key unlock) Mandatory
H2/10 Lt. Blue/Black (-) PTS Output [3] Push Start Switch, black 10 pin plug, pin 5
This connection is only required for Pit Stop/ Idle mode in manual
transmission vehicles or Ready mode for vehicles with hybrid engines.
- Gray Remote Start
Only
H2/11 Brown/Red (+) Siren Output [2] The siren is only required when enabling the security features during
module flashing.
Security Only
H2/12 Pink No Connection No Connection
H2/13 Violet No Connection No Connection
H2/14 Brown No Connection No Connection
H2/15 White/Blue No Connection No Connection
H2/16 Red/Blue No Connection No Connection
H2/17 Black/White No Connection No Connection
H2/18 Orange/Black No Connection No Connection
H2/19 Blue No Connection No Connection