DKS 6300 Series User manual

Shadow Loop
Reverse Loop
v
v
Re
Re
Rev
e
e
e
ev
ev
e
eve
e
e
s
s
se
L
L
e
e
e L
p
p
o
o
op
op
op
o
op
3 2 1
20
11 7
5”
High Voltage
Conduit
QUICKSTART “BASIC” GUIDELINES FOR MODEL 6300 - FOR GATES UP TO 18 FEET AND OPENING 90°
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
115 VAC
C
C
Not included - Refer to the Installation/Owner’s
manual and Loop Information Manual (available
FREE from www.dkaccess.com) for more
information on loops and loop detectors.
Radio Receiver
Loop Detectors
D
D
D
Not included - Refer to a specific Radio Receiver
Manual (available from www.dkaccess.com) for
more information on radio receivers and antenna
installation. (See reverse side for wiring)
High Voltage Connection
Tip: It is recommended that a surge suppressor
be installed on the high voltage power lines.
GATE OPERATOR MUST BE PROPERLY GROUNDED!!
Copyright 2012 DoorKing, Inc. All rights reserved. 6300-066-G-12-12
Important: The elbow
assembly must be in
the correct position
on the arms BEFORE
cycling operator the
first time.
A
Neutral 115 VAC
Chassis
Ground
DANGER
HIGH VOLTAGE!
Model 6300 is intended for installation
only on swing gates used for vehicles.
Pedestrians must be supplied with a separate
access opening.
For safety and installation instructions, please
refer to the Installation/Owner’s manual.
Safety
Cover
A
Low
Volt
3/4”
with Sweeps
High
Volt
Elbow Assembly
Elbow Flange
Loop Conduit
Flexible
Conduit
Depth of the
concrete is
determined by
soil conditions
and local
building codes.
Junction Boxes
AC
Power
Conduit
90°
Open Gate
Note: 2” thick gate Illustrated.
Note: 2” thick
gate Illustrated.
Closed Gate
3”
Gate Bracket
Pad Base Gate Bracket
Post Base Gate Bracket
Operator
Output
Shaft
Important: A straight
line drawn from the
closed gate bracket
through the open
gate bracket MUST
intersect the operator
output shaft.
Important: Elbow flange MUST be on
the opposite side of the closed gate.
Manually adjust the arms to get the
correct open and closed positions
BEFORE powering up the operator.
Open/Close limits will be automatically
set the first time operator is cycled.
37.5” 24”
Operator Position
Concrete Position
Gate Bracket
Height
Post
Base
Pad
Base
Open Gate
Closed Gate
23”
12”
22”
90° 90°
Run conduit on
the opposite
side of the
open gate for
the post base.
Secure operator
to the concrete
pad with six (6)
3/8” x 3” sleeve
anchors
(not supplied).
Mount the
post base into
the concrete
before
installing the
operator.
Closed Gate
3”
1.5”
3”
Conduit
Conduit
Right Support Leg
Left Support Leg
Open Gate
Bottom Plate of 6300
Important: Adjust the locknut on the crank power arm
so that it is snug against the washer, but will still allow
the 30” crank arm to rotate with little force.
30” Crank Arm
Bottom Plate of 6300
60” Connecting Arm
Flange
Crank Power Arm
Elbow Assembly
Brass Bushing
Gate
Bracket
Ground
Arms and Operator
MUST be level.
Varies with base used.
5”
Manual Release
DIP-Switch Settings
•NO AC power.
•NO DC power (On select models).
Output Shaft
Position
Output
Shaft
Pad MUST
be Level.
Post Base
MUST be Level.
Post
Base
Concrete Pad
Concrete
1
2
Crank Power Arm
Crank Arm
3/8
Using shadow loop and gate opening
in direction shown.
SW 1
1. OFF
2. OFF
3. OFF
4. ON
5. ON (Operator Type)
6. OFF
7. ON (Single Operator)
8. ON (Tamper Protect)
1. OFF (Opening Counter-Clockwise)
2. OFF
3. OFF
4. OFF
5. OFF (Normal Reverse Function)
6. OFF
7. OFF
8. OFF
SW 2
Auto Close
Timer
Adjust
1 to 23 sec.
B
B
34” 12”
43”
1. Com to #20
2. Relay to #11
3. 24 Volt to #7
12” 12”
23”
30”
16.5”
43”
43”
2”
14”
10”
Note: “Optional” High Voltage Kit
black and white wires connect the
same as shown. See High Voltage
Kit instruction sheet for more
information.
(See reverse side)

Switch Function Setting Description
OFF
ON
OFF
ON
OFF
ON
OFF
ON
1-OFF
1-OFF
1-ON
1-ON
2-OFF
2-ON
2-OFF
2-ON
Auto-Close
Timer
Slide Gate
Swing Gate
Dual Operators
Single Operator
Circuit
Board
Relay
3
4
5
7
1 and 2
Auto-close timer is OFF. Manual input required to close gate.
Auto-close timer is ON. Adjustable from 1-23 seconds to close gate.
OFF for Slide gate operator (DO NOT use for 6300).
Normal Setting. ON for Swing gate operator (Switch MUST be ON for 6300).
OFF
ON
3-Button
Single Button
6OFF when using a 3-button station (DoorKing 3-button control stations only).
ON when using a single button control, terminals 13 &14 become a STOP input.
Switch must be OFF when bi-parting (dual) gates are used.
Switch must be ON for single operator.
OFF
ON
Tamper Protect
8Tamper protect is OFF.
Normal Setting. Tamper protect is ON.
Relay activates when gate is open (Shadow loop setting when used).
Relay activates when gate is not closed.
Relay activates when gate is opening and open.
Relay activates when gate is opening and closing.
The output wired to terminal #12 becomes the output from the exit loop detector
plugged into the EXIT Loop port.
Normal Setting. Terminal #12 is a normal full open input.
Exit Loop Port
Output
Full Open Input
Every time the operator is powered up, the First open command
will automatically set the open and close limits of the gate.
SW 1
1
ON
2 3 4 5 6 7 8
SW 2
1
ON
2 3 4 5 6 7 8
SW 1 DIP-Switches
SW 2 DIP-Switches
OFF
ON
Reverse Loop
Shadow Loop
Terminal 15 is a normal Reverse input.
Terminal 15 is a Shadow input. Gate will NOT stop during the close cycle.
Switch Function Setting Description
Secondary 6300
Changes Gate
Opening
Direction
OFF
ON
OFF
ON
Self-Test
Motor Control
for Secondary
Operator
Primary 6300
Changes Gate
Opening
Direction
2
3
4
6
1
Normal Setting. Normal operation.
Self-test mode. Operator MUST be disconnected from gate to run self test.
Switch is OFF when both primary and secondary operator motors are powered
from main terminals 4 and 5. Applies to operators originally manufactured with
4501, Rev O boards or lower).
Switch is ON when secondary operator motor is powered from the secondary
motor terminals. Applies to operators manufactured with 4501, Rev P boards and
higher, and all 4502 boards.
5
7
8
Gate Overlap
Not Used
Not Used
OFF
ON
OFF
OFF
Primary and secondary operators start at the same time.
Secondary operator starts 1-2 seconds prior to primary operator.
Leave in the OFF position.
Leave in the OFF position.
ON OFF
Opens
Clockwise
Opens
Counter-Clockwise
Same as above, for secondary 6300 ONLY.
3-Wire Radio Receiver
Limited to 250 ma.
Power (24 Volt DC) and
logic output. Power is
shut off .5 sec. prior to
gate starting and remains
off while gate is opening
and in the open position.
Com
Relay
Red Open
Green Close
White Com
24 Volt
Com
Com
Key Switch
Stand-Alone
Keypad
Stand-Alone
Card Reader
Telephone
Entry
Note: All stand-alone and
telephone entry devices must
use a separate power source.
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
NC
NO
1
ON
2 3 4 5 6 7 81
ON
2 3 4 5 6 7 8
Magnetic Lock
3-Button Station
DoorKing ONLY
SW 1
SW 2
SW 1, switch 3 must be ON.
#12 - Safety
Opening Device
Radio
Open
Access
Device
Open
Safety
Open
#11 - Access Control
Devices
Com
Com
(2) Two 115 VAC
Convenience Outlets
SW 1
1
ON
234 5 6 7 8
Important: Controls must be installed a minimum
of 10-feet from the gate or installed in such a way
that the person using the control cannot come in
contact with the gate or gate operator.
24 Volt
1 amp max.
Coax Antenna Kit
P/N 1514-073
Antenna mounted
outside operator cover.
Main Terminal
QUICKSTART “BASIC” GUIDELINES FOR MODEL 6300 - DIP-SWITCH AND WIRING REFERENCE
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
Model 6300 is intended for installation only on swing gates used for vehicles.
Pedestrians must be supplied with a separate access opening.
For safety and installation instructions, please refer to the Installation/Owner’s manual.
Convenience Open Radio
Receiver Note:
Wiring may differ.
See section 7 in the
Installation/Owner’s
manual for more info.