DMP Electronics 734B Installation guide

INSTALLATION AND PROGRAMMING GUIDE
734B Access
Control Module

About the 734B .......................................... 1
Power Supply......................................................... 1
Zone Terminals ...................................................... 1
Annunciators.......................................................... 1
Indicator LEDs ....................................................... 1
Form C Relay......................................................... 2
Programming Connection................................ 2
Keypad In and Out Connections ................... 2
PCB Features...............................................3
Install the 734B...........................................4
Wire the Magnetic Lock.................................... 5
Isolation Relay (optional) ................................. 7
Install the 333Suppressor ............................... 8
Wire the Zone Terminals................................... 9
Connect a Magstripe Reader.......................... 11
Set the 734B Address.......................................14
Program the 734B .................................... 17
Program BINs as User Codes.........................18
Program BINs Locally .......................................18
Program the Module in Standalone Mode 19
TABLE OF CONTENTS
Programming Reference ........................ 20
Program Start Display .....................................20
Serial Number .....................................................20
Initialization Option ..........................................20
Initialize Confirm Option ................................20
Activate Zone 2Bypass...................................21
Zone 2 Bypass Time.........................................22
Relock on Zone 2Change.............................. 22
Activate Zone 3Request to Exit .................23
Zone 3REX Strike Time..................................24
Activate Onboard Speaker............................24
BIN Code Length ..............................................24
Enable Local Processing ................................24
BIN Code .............................................................24
No Communication with Panel ....................25
Remove Keypad.................................................26
Keypad Bus Wiring Specifications.........27
Product Specifications ............................28
Readers ..................................................... 29

Digital Monitoring Products, Inc. | 734B Installation and Programming Guide 1
Annunciators
An onboard programmable piezo provides
local annunciation at the 734B. You can
also connect a variety of switched ground
annunciators to the 734B for remote
annunciation.
Indicator LEDs
The 734B provides three indicator LEDs.
The red LED turns on for the same
duration as the door strike relay. The
yellow LED turns on for one second to
indicate receipt of a valid input. The green
LED indicates that data is being sent to
the panel.
The 734B Access Control Module allows you to use the powerful built‑in access control
capability of DMP Panels. The module is designed specifically to support BIN tables for
the banking industry. For example, use the 734B to control access to ATM vestibules with
magstripe readers.
Connect a 734B to a DMP panel’s Keypad Bus or AX‑Bus to use the powerful built‑in
access control capability of DMP panels or install the module as a standalone access
control device. The 734B includes the following features:
Power Supply
The 734B operates at 12/24VDC from
the power supply supporting a door’s
magnetic lock or door‑strike.
Warning: To avoid the risk of
equipment damage, do not exceed
750mA total output current for zones
connected to the module.
Zone Terminals
Zones 1, 2, and 3on the 734B can be
programmed for a variety of burglary or
access control applications.
ABOUT THE 734B

2 734B Installation and Programming Guide | Digital Monitoring Products, Inc.
Form C Relay
The 10Amp Form C relay draws up to
35mA of current. Refer to the NC/C/NO
(Dry Contact Relay) and the Isolation
Relay sections in this document for more
information.
Programming Connection
The 734B also provides a keypad
programming connection that allows
you to use a standard DMP LCD keypad
for initial setup. Programming can be
completed using a keypad connected to
the 734B or from XR150/XR550Series
panels.
Keypad In and Out
Connections
The keypad in (KYPD IN) connection
receives and transmits data to the panel
keypad bus or AX‑Bus.
The keypad out (KYPD OUT) connection
receives and transmits data out to other
keypads or modules. Install a dual
connector four‑position harness to allow
daisy chain connection to other devices,
up to the maximum number of devices
supported. XR150Series panels support
up to 8devices. XR550Series panels
support up to 16devices. When using the
AX‑Buses with XR550devices, you can
have 32doors, expandable to 96.
Caution: When the 734B is powered
from 24VDC, do not connect devices
to KYPD OUT header.

Digital Monitoring Products, Inc. | 734B Installation and Programming Guide 3
PCB FEATURES
RED
PROG
J2
RED
J5
J4
KYPD OUT
S1
J3
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NC
C
NO
GRN
YEL
RED
+ –
ON
Piezo
1234 5 6 7 810 11 12 13 14
9
LC ASRED WHT GRN BLK Z1 Z2 Z3 Z4+ Z4–RA GND GND
KYPD IN RED
Door Relay
Terminal
Inputs
Status
Indicator
Outputs Zones
To Panel
Keypad Bus
or AX‑Bus
To Other
Keypad Bus
or AX‑Bus
Piezo
Indicator
LEDs
Keypad
Programming
Header
Address DIP
Switches
Figure 1: PCB Features

4 734B Installation and Programming Guide | Digital Monitoring Products, Inc.
INSTALL THE 734B
Mount the 734B
The module comes in a high‑impact plastic housing that you can mount directly to a
wall, backboard, or other flat surface.
For easy installation, the back and ends of the 734B housing have wire entrances. The
back also contains multiple mounting holes that allow you to mount the module on
a single‑gang switch box. DMP recommends mounting the 734B near the protected
door. See Figure 2for mounting hole locations on the housing base.
1
1. Remove the PCB from the
plastic housing by loosening
the clips on one side and gently
lifting it out of the housing base.
2. Insert the included screws in the
desired mounting hole locations
and tighten them to secure the
housing to the surface.
3. Reinstall the PCB in the housing
base.
Mounting Holes
Figure 2: Mounting Hole Locations

Digital Monitoring Products, Inc. | 734B Installation and Programming Guide 5
Wire the Magnetic Lock
The 734B provides a Form C (SPDT) relay for controlling locks and other
electronically‑controlled barriers. The three relay terminals marked NO C NC allow
you to connect the device wiring to the relay for module control.
Use an additional power supply to power magnetic locks and door strikes. See
Figure 3and Figure 4for typical magnetic lock and door strike wiring.
The Form C relay draws up to 35mA of current and contacts are rated for 10Amps
(resistive) at 12/24VDC. When connecting multiple locks to the Form C relay, the
total current for all locks cannot exceed 10Amps. If the total current for all locks
exceeds 10Amps, problems may arise and an isolation relay may be needed. See the
Isolation Relay section for information.
2
PROG
J2
RED RED
KYPD IN
J4
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Suppressor
Normally Closed
–
+
Magnetic Door Lock
12/24 VDC
Power Supply
Figure 3: Typical Magnetic Lock Wiring
PROG
J2
RED
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Suppressor
Normally Open
–+
DC Door Strike
12/24 VDC
Power Supply
Figure 4: Typical Door Strike Wiring

6 734B Installation and Programming Guide | Digital Monitoring Products, Inc.
KYPD IN / KYPD OUT Connections
• KYPD IN (Keypad In): Receives and transmits data to the panel Keypad
bus/AX‑Bus.
• KYPD OUT (Keypad Out): Receives and transmits data out to other keypad(s) or
module(s). Install a dual‑connector harness to allow connection to other devices
up to the maximum number of devices supported.
When the 734B is powered from 24VDC, do not connect devices to KYPD OUT header.
Status LEDs
The 734B board contains three status LEDs.
• The Red LED turns on for the same duration as the door strike relay.
• The Yellow LED turns on for one second to indicate receipt of a valid input.
• The Green LED indicates data sent to the panel.