DMP Electronics 734N Series Installation guide

INSTALLATION AND PROGRAMMING GUIDE
734N Series Wiegand
Interface Modules

About the 734N Series .............................. 1
Power Supply......................................................... 1
Zone Terminals ...................................................... 1
Annunciators.......................................................... 1
Indicator LEDs ...................................................... 2
Form C Relay......................................................... 2
Programming Connection................................ 2
PCB Features...............................................3
Install the 734N Series Module.................4
Mount the 734N ................................................... 4
Wire the Electronic Lock.................................. 5
Isolation Relay (optional) ................................. 8
Install the 333Suppressor ............................... 9
Wire the Zone Terminals..................................10
Connect a Card Reader....................................12
Network Connection.........................................15
Set the 734N Address.......................................16
Connect the Power Supply.............................18
TABLE OF CONTENTS
Program the 734N Series Module.......... 19
Version Display...................................................20
Zone Status Display..........................................20
Diagnostic: Menu ...............................................20
Connect Status....................................................21
Programming Menu..........................................22
Initialization Options........................................ 22
Initialization: Communication.......................22
Initialize Confirm Option ................................22
Initialization: Access.........................................23
Initialize Confirm Option ................................23
Communication Menu......................................23
734N Device Number .....................................23
734N DHCP..........................................................24
734N IP Address................................................24
Subnet Mask........................................................24
Gateway Address ..............................................24
Panel IP Address................................................24
Panel IP Port........................................................25
734N Passphrase ...............................................25
Access Options ..................................................25

Activate Zone 2Bypass..................................26
Zone 2Bypass Time......................................... 27
Relock on Zone 2Change.............................. 27
Activate Zone 3Request to Exit .................28
Zone 3 REX Strike Time..................................29
Activate Onboard Speaker............................29
Card Formats ......................................................29
Custom Card Definitions ........................ 30
Card Format Number...................................... 30
Format Name.......................................................31
Wiegand Code Length.....................................31
Site Code Position and Length ....................32
User Code Position and Length...................32
Require Site Code .............................................33
Site Code ..............................................................33
Number of User Code Digits.........................34
No Communication with Panel ....................35
Stop .......................................................................36
Public Card Formats ................................37
734N Series Network Specifications .....38
Compliance Listing Specifications ....... 40
UL Access Control............................................ 40
ULC Commercial Burglary
(XR150/XR550Series Panels)......................42
Certifications............................................ 43
Underwriters Laboratory (UL Listed)........43
Product Specifications ........................... 44
Readers and Credentials ........................ 46

Digital Monitoring Products, Inc. | 734N Series Installation and Programming Guide 1
Zone Terminals
Four input zones are provided to allow
connection of nearby burglary devices.
Annunciators
An onboard programmable piezo provides
local annunciation at the module. You can
also connect a variety of switched ground
annunciators to the module for remote
annunciation.
The 734N, and 734N‑POE Wiegand Interface Modules allow you to add IP network
access control capability to XR150/XR550Series panels using proximity, credential, or
mag‑stripe card readers. The modules also allow you to use the powerful built‑in access
control capability of DMP Panels.
Power Supply
734N Series modules operate at
12/24VDC from the power supply
supporting a door’s magnetic lock or
door‑strike. The 734N‑POE can also be
powered from POE.
Warning: To avoid the risk of
equipment damage, do not exceed
750mA total output current for zones
connected to the module.
ABOUT THE 734N SERIES

2 734N Series Installation and Programming Guide | Digital Monitoring Products, Inc.
Indicator LEDs
734N Series modules provide three indicator LEDs. The red LED turns on for the same
duration as the door strike relay. The yellow LED turns on for one second to indicate
receipt of a valid Wiegand input. The green LED indicates that data is being sent to the
panel.
Form C Relay
The 10Amp Form C relay draws up to 35mA of current. See NC/C/NO (Dry Contact
Relay) and Isolation Relay for more information.
Programming Connection
The modules also provide a keypad programming connection for use with a standard
DMP LCD keypad for initial setup. Programming can be completed using a keypad
connected to the module or from XR150/XR550panels.

Digital Monitoring Products, Inc. | 734N Series Installation and Programming Guide 3
PCB FEATURES
DC
Input
Wiegand
Inputs Zones
Piezo
Indicator
LEDs
Door Relay
Network
Connection
Figure1: PCB Features
Keypad
Programming
Header
Status
Indicator
Outputs
Output 1
Reset Header
Output 2

4 734N Series Installation and Programming Guide | Digital Monitoring Products, Inc.
INSTALL THE 734N SERIES MODULE
Mount the 734N
The module comes in a high‑impact plastic housing that you can mount directly to a
wall, backboard, or other flat surface.
For easy installation, the back and ends of the 734N housing have wire entrances. The
back also contains multiple mounting holes that allow you to mount the module on
a single‑gang switch box. DMP recommends mounting the 734N near the protected
door. See Figure2for mounting hole locations on the housing base.
1
1. Remove the PCB from the
plastic housing by loosening
the clips on one side and gently
lifting it out of the housing base.
2. Insert the included screws in the
desired mounting hole locations
and tighten them to secure the
housing to the surface.
3. Reinstall the PCB in the housing
base.
Mounting Holes
Figure2: Mounting Hole Locations

Digital Monitoring Products, Inc. | 734N Series Installation and Programming Guide 5
Wire the Electronic Lock
The module provides a Form C (SPDT) relay for controlling locks and other
electronically‑controlled barriers. The three relay terminals marked NO C NC allow
you to connect the device wiring to the relay for module control.
When the 734N Series module is powered with a 12/24V power supply, the device
can power an electric strike, up to 750mA. See Figures 3and 4for typical magnetic
lock and door strike wiring. The 734N‑POE can also be powered with POE. See
Figure5for POE door strike wiring.
The Form C relay draws up to 35mA of current and contacts are rated for 10Amps
(resistive) at 12/24VDC. When connecting multiple locks to the Form C relay, the
total current for all locks cannot exceed 10Amps. If the total current for all locks
exceeds 10Amps, problems may arise and an isolation relay may be needed. See
Isolation Relay for more information.
2

6 734N Series Installation and Programming Guide | Digital Monitoring Products, Inc.
PROG
J2
RED RED
KYPD IN
J4
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Suppressor
Normally Closed
–
+
Magnetic Door Lock
12/24 VDC
Power Supply
PROG
J2
RED
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Suppressor
Normally Open
–+
DC Door Strike
12/24 VDC
Power Supply
Figure4: Typical Door Strike WiringFigure 3: Typical Magnetic Lock Wiring