Dogtra YS300 User manual

1
YS300
NO BARK COLLAR
Owner's Manual
Please read this manual thoroughly
before operating the YS300.

2 3
WARNING
Please read all safety and product information below
before using your Dogtra product. Failure to follow these
safety instructions could result in injury to you, your dog
and others, or it could result in damage to your Dogtra
product or other property.
PRODUCT SAFETY
Training Methods
Dogtra products may be used with a variety of training
methods. However, each dog may have a dierent
reaction to training methods and to Dogtra products.
Closely observe your dog when determining the right
training method to use with your Dogtra product.
Aggressive Dogs
Do not use Dogtra products with aggressive dogs as such
dogs may react adversely and cause injury to people or
other dogs. Seek the assistance of a dog-training specialist
or veterinarian when dealing with aggressive dogs.
Children
Dogtra products are not toys. Adult supervision and close
attention are necessary when Dogtra products are used by
or near children.
PRODUCT DAMAGE
Electrical Product
Your Dogtra product contains electrical components and
batteries. Do not use or keep your product near heat or
flammable sources. Such use or storage may damage your
product and/or cause fire, explosion, injury, or property
damage.
Medical Device Interference
Dogtra products contain electrical and magnetic
components that emit low level electromagnetic waves and
radio frequencies. These electromagnetic waves or radio
frequencies may interfere with pacemakers, defibrillators,
or other medical devices. Consult your physician or medical
device maker before using your medical device with a
Dogtra product. If you think that your Dogtra product is
interfering with your pacemaker, defibrillator, or other
medical device, stop using the Dogtra product.
Inadvertent Activation
The digital microprocessor offers thousands of unique
codes to eliminate frequency match-up with other Dogtra
e-collars. The Constant button will automatically shut down
after being held down for 12 seconds or more as a safety
feature.
IMPORTANT SAFETY AND PRODUCT
INFORMATION

4 5
CONTENTS
AT A GLANCE .................................................................
MAIN FEATURES ............................................................
OVERVIEW ......................................................................
USING THE ON/OFF & STIMULATION DIAL ..........
LED INDICATOR .............................................................
TESTING THE YS300 ....................................................
CHARGING THE BATTERY ..........................................
RECEIVER FITTING ........................................................
MAINTENANCE ...............................................................
TROUBLESHOOTING GUIDE ......................................
WARRANTY AND REPAIR INFORMATION .............
6
6
7
8
10
11
12
15
17
18
20
UNAUTHORIZED USE
Your Dogtra product should be used only in a humane
manner to train and educate your dog. Dogtra products are
not intended for use in any other manner nor are they
intended for use with other animals or with humans.
BATTERY
Your Dogtra product contains batteries. Take care when
removing and installing batteries as your fingers may get
caught. Dispose of batteries as provided by your local
regulations. Do not disassemble, crush, heat, or otherwise
alter the battery as it may cause fire, injury or property
damage.

6 7
MAIN FEATURES
• Pager vibration (P) warning prior to the stimulation
• 6 intensity levels (2-7) for a wide variety of dispositions
• Test mode (T) for testing the YS300
• Fully waterproof receiver
• Medium output receiver
• Sound Recognition Sensor
• For dogs as small as 10 lbs
• 2-hour rapid charge lithium polymer battery
AT A GLANCE
YS300
No Bark Collar
Battery
Charger
Owner's
Manual
OVERVIEW
Collar Strap
Contact
Points
On/Off &
Stimulation
Dial
Sound Recognition
Sensor
LED Indicator Light
Battery Charging
Receptacle
& Rubber Plug

8 9
- The On/Off & Stimulation Dial is used to turn the YS300
on/off and to select the stimulation level.
- Set the dial to "OFF" to turn off the YS300.
- Set the dial to "P" for the Pager vibration only mode.
- The YS300 has stimulation levels 2 (lowest) through 7
(highest). Each stimulation level begins with a vibration
and is followed by the stimulation.
- Set the dial to "T' to test the YS300. See TESTING THE
YS300 on page 11 to check if your unit is working
properly.
On/Off & Stimulation Dial Function
OFF Power Off
P Pager Vibration
2~7 Stimulation Level
T Test Mode
Note: When first using the YS300, it is recommended to
start at the lowest stimulation level. If your dog continues
to bark, gradually increase the stimulation level. Closely
monitor your dog’s reaction to find the right stimulation
level for you dog.
USING THE ON/OFF &
STIMULATION DIAL

10 11
The LED indicator light will flash for 1 second when the
YS300 has been turned on and then flash every 2 seconds.
If the dog does not bark for over 10 seconds, it will turn to
sleep mode to conserve battery life and the LED will turn
off.
Before going into sleep mode, the LED light flashes
green when the battery is fully charged and turns to
amber when the battery life is getting low. When the LED
indicator emits a blinking red light, the battery needs to be
recharged.
LED INDICATOR
Battery life
LED window
Full charge Medium charge Needs charge
In Use Green Amber Red
Charging Green Red Red
TESTING THE YS300
1. Turn the dial on the YS300 to "T" to set the system to
test mode.
2. Test the unit by scratching the TEST area on the receiver
(as shown in the diagram) with a coin or pen. The
receiver will emit a vibration three times. Repeat the
same process to test again.
3. The YS300 has a preset delay of 15 seconds in between
corrections. Once the unit activates, it will not activate
again until 15 seconds has gone by. The reason for the
delay is so that your dog figures out the implications
of the corrections from barking before being corrected
again.
* When on the test mode, the YS300 emits a vibration
without emitting stimulation at the same time.
* When on the test mode, the sensor is more sensitive and
can be easily activated by a small sound or tap.

12 13
CHARGING THE BATTERY
1. Charge the unit before using the unit for the first time.
2. Do not charge the batteries near any flammable
substances.
3. Fully charge the batteries if the unit is to be stored
without use for a period of 3 months or more.
Recharge the Unit If:
• The LED indicator light on the receiver is emitting a
red color.
• The indicator light on the receiver will not come on.
The YS300 uses lithium-polymer batteries. The battery
charger is designed for a 120 volt wall outlet.
Note 1: Only use Dogtra-approved lithium polymer
batteries and chargers for your Dogtra unit. This will
prevent any damage that can be incurred from attempting
to use a different charger.
Note 2: The unit has a partial charge when it leaves the
Dogtra facility. Upon receipt of the collar, be sure to give
it a full 2-hour initial charge before the first use. When a
charger is not in use, disconnect it from the power source.
Battery Charging Procedure

14 15
Proper Fit
The receiver should be fitted so that the surgical stainless
steel contact points press firmly against the dog’s skin. You
should be able to fit a finger in between the contact point
and your dog’s skin. The best location is on either side of
the dog’s windpipe.
Improper Fit
A loose fit can allow the collar to move around on the dog’s
neck. When this happens, the contact points may rub
against the skin and cause irritation. If the receiver is too
loose, the contact will not be consistent and cause the
corrections to be inconsistent. Dogtra uses surgical
stainless steel contact points and anti-microbial plastic to
protect the dog’s skin.
RECEIVER FITTING
1. Attach the charging cable to the receiver, as shown on
page 13.
2. Plug the charger into a 120 volt wall outlet or, if using the
auto charger, plug into a cigarette lighter only for lithium
polymer batteries (use a 230 volt European charger
for Europe). All indicator lights should glow red when
properly plugged in and the unit will automatically shut
off during the charging process. You will need to turn the
unit on again before use once the unit is fully charged
and unplugged from the battery cable.
3. The lithium polymer battery is fully charged within
2 hours. The lights will stay red during the charging
process. The red light will turn green once the unit is
fully charged.
4. After charging, cover the battery charging receptacle
with the rubber plug on the receiver.

16 17
Attention!
Leaving the receiver in the same location on the dog’s
neck for an extended period of time can cause skin
irritation. If the dog is to wear the receiver for long
periods, occasionally reposition the receiver so that the
contact points are moved to a dierent location on the
dog’s neck. Make sure you check for skin irritation each
time you use the unit. Remove all other collars when
using the YS300 since additional collars or buckles may
inadvertently activate the unit.
MAINTENANCE
Basic Maintenance
Be sure the rubber charging cap is securely in place when
the collar is in use. After each training session, carefully
inspect the unit for any missing parts or damage to the
casing. Damaged or broken casing may aect the
waterproof guarantee on the unit. After confirming that
there is no damage to the casing, rinse the receiver and
clean out any dirt or debris.
Storage Maintenance
The YS300 should be fully charged before storing for
extended periods. While in storage, the unit should be
given a full charge once a month and before the first use.
Store the units in room temperature. Do not keep the units
exposed to extreme climates.
Troubleshooting
If the unit is malfunctioning, please refer to the
“Troubleshooting Guide” before sending it to Dogtra for
service. If you have any questions or concerns, you may
email them to [e-mail], or call customer service
at [phone].

18 19
1. My dog is not reacting to the receiver.
- Make sure the receiver is turned on.
- Be sure the strap is on the dog tight enough so that
both contact points are touching the dog’s skin.
– The contact points may be too short for the dog. To
place an order for longer contact points that are more
appropriate for your dog, please call [phone].
If you are already using the longest contact points
available, you might need to trim down the hair on the
dog’s neck so both contact points are touching the
dog’s skin.
– The intensity level may be too low for your dog. Keep
increasing the stimulation until the dog responds,
usually with neck movement, head shaking, looking
over its shoulder, etc. (response may be very subtle).
2. My YS300 is not holding a charge.
– The batteries might not be charged properly, or
the charger, splitter, and the charging port may not be
functioning properly. You can send in your charging
units to have us inspect them.
– The charging pin may be damaged. Inside the charging
port, there is a metal pin that should be standing
straight up and stiff. If the pin is wobbling, broken, or
missing, you will need to send the unit in to the Repair
Department. The charging port must be clean prior to
charging; clean the dirt out with a cotton swab and
some rubbing alcohol. If the dog is in salt-water, be
TROUBLESHOOTING GUIDE sure to rinse the receiver and charging port with clean
water.
– If the above does not resolve your issues, contact
Dogtra customer service at [e-mail] or
[phone].
3. My dog has skin irritation.
- Leaving the receiver in the same location on the
dog’s neck for an extended period of time can cause
skin irritation. If the dog is to wear the receiver for
long periods, occasionally reposition the receiver so
that the contact points are moved to a different
location on the dog’s neck. Make sure you check for
skin irritation each time you use the unit.