Dometic CFX3 Series User manual

MOBILE COOLING
CFX3 PROTECTIVE COVERS
Form No. 3317446.000 02/20 | ©2020 Dometic Corporation
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
CFX3-PC35, CFX3-PC45, CFX3-PC55, CFX3-PC75, CFX3-PC95, CFX3-PC100
EN CFX3 Protective Covers
Installation Manual.....................2

2EN
Contents CFX3 Protective Covers
1 Explanation of Symbols and Safety
Instructions ............................ 2
1.1 Recognize Safety Information .............2
1.2 Understand Signal Words................2
1.3 Supplemental Directives .................2
1.4 General Safety Messages ................2
2 Intended Use ........................... 2
3 Installation ............................. 3
3.1 Preparing the Protective Cover............3
3.2 Attaching the Protective Cover............3
3.3 Placing the Lid Cover....................5
4 Maintenance ........................... 6
5 Disposal ............................... 6
6 Warranty Information.................... 7
6.1 United States and Canada ...............7
6.2 Asia-Pacific (APAC) Countries .............7
6.3 All Other Regions ......................7
Contents
Service Center & Dealer Locations
Visit: www.dometic.com
Read these instructions carefully. These instructions
MUST stay with this product.
DANGER!
Indicates a hazardous situation that, if not avoided,
will result in death or serious injury.
WARNING
Indicates a hazardous situation that, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a hazardous situation that, if not avoided,
could result in minor or moderate injury.
NOTICE: Used to address practices not related to
physical injury.
IIndicates additional information that is not related
to physical injury.
1.3 Supplemental Directives
To reduce the risk of accidents and injuries, please
observe the following directives before proceeding to
install this appliance:
• Read and follow all safety information and
instructions.
• Read and understand these instructions before
installing this product.
• The installation must comply with all applicable local
or national codes.
1.4 General Safety Messages
NOTICE: Failure to obey the following notices could
result in product failure:
• Avoid improper installation, adjustment, alterations,
or maintenance of this product.
• Do not modify this product in any way.
2 Intended Use
The CFX3 Protective Cover (also referred to as
“protective cover”) is designed and intended for use as
a protective cover for Dometic CFX3 coolers. Use these
instructions to ensure correct installation.
The manufacturer accepts no liability for damage in the
following cases:
• Faulty assembly or connection
1 Explanation of Symbols and
Safety Instructions
This manual has safety information and instructions to
help you eliminate or reduce the risk of accidents and
injuries.
1.1 Recognize Safety Information
This is the safety alert symbol. It is used to alert
you to potential physical injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
1.2 Understand Signal Words
A signal word will identify safety messages and property
damage messages, and also will indicate the degree or
level of hazard seriousness.

3
EN
CFX3 Protective Covers Installation
• Damage to the product resulting from mechanical
influences and excess voltage
• Alterations to the product without express permission
from the manufacturer
• Use for purposes other than those described in the
operating manual
Dometic Corporation reserves the right to modify
appearances and specifications without notice.
3 Installation
This section describes how to attach a protective cover
to a CFX3 cooler.
IThe images used in this document are for reference
purposes only. Measurements may vary ±0.38 in.
(10 mm).
3.1 Preparing the Protective Cover
q
we
r
1 Aligning the Cover and Feet (CFX3 75 shown)
qProtective Cover eFeet
wCooler rDrain Holes
1. Find a clean, flat place to prepare the protective
cover.
2. Making sure the lid of the cooler is secure, place the
cooler on its side.
3. Align the foot holes and drain holes on the
protective cover with the feet and drains on the
bottom of the cooler.
q
q
w w
2 Standing the Cooler Up (CFX3 45 and 75 shown)
qCooler wProtective Cover
4. Stand the cooler up, keeping the protective cover in
alignment with the holes underneath.
3.2 Attaching the Protective Cover
Use this section to find instructions for attaching the
protective cover to a specific CFX3 cooler model.
3.2.1 For CFX3 35 and CFX3 45 Coolers
q
w
e
3 Aligning the Molded Panel with the Cooler (CFX3 45 shown)
qMolded Panel eVentilation Holes
wCooler
1. Align the molded panel with the ventilation holes on
one side of the cooler.
2. Keeping the zipper clear, fit the molded panel to
the side of the cooler, starting at the bottom and
working up toward the top.
3. Repeat steps 1 and 2 for the other side.

4EN
Installation CFX3 Protective Covers
q
r
w
e
4 Attaching the So Cover to the Molded Panel
qSo Cover eZipper
wHandle Tab rMolded Panel
4. Position one end of the so cover.
5. Release the handle tab.
6. Attach the zipper between the so cover and the
molded panel on one side.
7. Pull the zipper down, across the bottom of the
cooler, and halfway up the opposite end.
8. Repeat steps 4–7 on the other side of the cooler.
9. Fully close both zippers.
w
q
5 Securing the Handle Tab
qHandle Tab wCooler Handle
10. Secure the handle tabs under the cooler handles.
3.2.2 For CFX3 55, CFX3 75, CFX3 95,
and CFX3 100 Coolers
e
w
r
q
6 Aligning the Molded Panel (CFX3 75 shown)
qMolded Panel eDisplay
wCooler rHandle Tab
1. Align the molded panel with the display clearance
hole to the display on the cooler display end.
2. Keeping the zipper clear, fit the display end molded
panel to the cooler, starting at the bottom and
working up toward the top.
3. Secure the handle tab under the handle.
e
q
w
7 Attaching the So Cover to the Molded Panel
qSo Cover eZipper
wMolded Panel

5
EN
CFX3 Protective Covers Installation
4. Begin fitting the next molded panel onto the opposite
end of the cooler by starting the zipper: attach the
zipper between the so cover and the molded panel,
then pull the zipper down a short distance.
5. Finish fitting the molded panel to the cooler.
6. Fully close the zipper.
7. Fully close the zipper on the display end.
3.3 Placing the Lid Cover
Use this section to find instructions for placing the lid
cover on a specific CRX3 cooler model.
3.3.1 For CFX3 35 and CFX3 45 Coolers
w
q
8 Removing the Lid Gasket (CFX3 45 shown)
qCooler Lid wLid Gasket
1. Gently pull out the lid gasket on the two long sides
of the lid.
e
w
q
9 Attaching the Lid Cover
qLid Cover eGasket Groove
wLid Cover Hook
2. Position the lid cover in alignment with the latch
clearance slot.
3. Insert the lid cover hooks into the gasket groove.
4. Refit the lid gasket, pushing it fully into the groove.
3.3.2 For CFX3 55 and CFX3 100 Coolers
q
w
10 Removing the Lid Gasket (CFX3 55 shown)
qCooler Lid wLid Gasket
1. Gently pull out the lid gasket on the two short sides
of the lid.
e
w
q
11 Attaching the Lid Cover
qLid Cover eGasket Groove
wLid Cover Hook
2. Position the lid cover so that the Dometic logo
direction matches the cooler Dometic logo
direction.

6EN
Maintenance CFX3 Protective Covers
3. Insert the lid cover hooks into the gasket groove.
4. Refit the lid gasket, pushing it fully into the groove.
3.3.3 For CFX3 75 and CFX3 95 Coolers
q
w
e
12 Aligning the Lid Covers (CFX3 75 shown)
qLid Cover eLocation Tab
wCooler Lid
1. Match the Dometic logo direction on one lid cover
to the Dometic logo direction on the cooler lid. The
location tab underneath the lid cover should face the
center of the cooler lids.
2. Open one cooler lid.
q
w
13 Removing the Lid Gasket
qCooler Lid wLid Gasket
3. Gently pull out the lid gasket on the two long sides
of the lid.
e
w
q
14 Attaching the Lid Cover
qLid Cover eGasket Groove
wLid Cover Hook
4. Insert the lid cover hooks into the gasket groove.
5. Refit the lid gasket, pushing it fully into the groove.
6. Repeat steps 1–5 for the other cooler lid and lid
cover.
4 Maintenance
Clean the protective cover regularly using a sponge
or clean towel with clean water. Do not use chemical
solvents or abrasive cleaners.
5 Disposal
MPlace the packaging material in the appropriate
recycling waste bins, whenever possible. Consult
a local recycling center or specialist dealer for
details about how to dispose of the product in
accordance with all applicable national and local
regulations.

7
EN
CFX3 Protective Covers Warranty Information
6 Warranty Information
Refer to the sections below for information about
warranty and warranty support in the US, Canada,
Australia, New Zealand, and all other regions.
6.1 United States and Canada
LIMITED WARRANTY AVAILABLE AT WWW.DOMETIC.
COM/WARRANTY.
IF YOU HAVE QUESTIONS, OR TO OBTAIN A COPY
OF THE LIMITED WARRANTY FREE OF CHARGE,
CONTACT:
DOMETIC CORPORATION
CUSTOMER SUPPORT CENTER
1120 NORTH MAIN STREET
ELKHART, INDIANA, USA 46514
1-800-544-4881 OPT 1
6.2 Asia-Pacific (APAC) Countries
If the product does not work as it should, please contact
your retailer or the manufacturer’s branch in your country
(see the back of this instruction manual for the web
addresses to locate your region or retailer). The warranty
applicable to your product is one year.
For repair and warranty processing, please include the
following documents when you send in the device:
• A copy of the receipt with purchasing date
• A reason for the claim or description of the fault
6.2.1 Australia Only
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
6.2.2 New Zealand Only
This warranty policy is subject to the conditions and
guarantees which are mandatory as implied by the
Consumer Guarantees Act 1993(NZ).
6.3 All Other Regions
The statutory warranty period applies. If the product
is defective, please contact the manufacturer’s branch
in your region or your retailer (see the back of this
instruction manual for the web addresses to locate your
region or retailer).
For repair and guarantee processing, please include the
following documents when you send in the device:
• A copy of the receipt with purchasing date
• A reason for the claim or description of the fault

Mobile living made easy.
dometic.com
YOUR LOCAL
DEALER
dometic.com/dealer
YOUR LOCAL
SUPPORT
dometic.com/contact
YOUR LOCAL
SALES OFFICE
dometic.com/sales-offices
A complete list of Dometic companies, which comprise the Dometic Group, can be found in the public filings of:
DOMETIC GROUP AB Hemvärnsgatan 15 SE-17154 Solna Sweden