Dorma 8916 TDE User manual

PAGE
INS NO. Rev.
08279351 09/09
1 of 3
(4)
8916 / 8956 TDE, TDEH
1
2
4
TRACK DOUBLE EGRESS - PULL SIDE MOUNT
AND ACCESSORY PLATE BP89
WOOD FRAME
METAL FRAME
QTY
(4)
(4)
HOLD OPEN MECHANISM
(LH DOOR)
as shown. Arrow on plate to point toward arm
(RH DOOR)
BP89 Plate applications only. Attach plate to door
attachment.
3
QTY
(4)
QTY
QTY
METAL FRAMES
QTY
(4)
L
WOOD FRAMES
PLATE
(LEFT HAND DOOR)(RIGHT HAND DOOR)
L
HINGES
CHINGESC
Attach closer to door or plate with sweep and
latch valves facing hinges.
according to appropriate template.
Determine hand of door. Prepare door and frame
(REFERENCE UNIT CARTON FOR ACCESSORIES AND
OPTIONS SUPPLIED)
LISTINGS.
IDENTIFIED IN THE INDIVIDUAL DOOR MANUFACTURER'S
DOORS, UNLESS AN ALTERNATIVE METHOD IS
WOOD OR PLASTIC FACED COMPOSITE TYPE FIRE
OF COMPONENTS TO UNREINFORCED DOORS AND TO
CAUTION: SEX NUTS ARE REQUIRED FOR ATTACHMENT
REVERSE BEVEL
RIGHT HAND DOOR
LEFT HAND DOOR
REVERSE BEVEL
RIGHT HAND LEFT HAND
(WOOD)
(METAL)
(2)
QTY
(2)
QTY
L HINGES
M6 HEX KEY
ARM TO SLIDE SHOE
(1)
QTY
C
END BLOCK
END BLOCK
END BLOCK
L HINGES
(TDEH UNITS ONLY)
SLIDE SHOE
C
RUBBER STOP
SLIDE SHOE
into track and attach track to frame.
(TDE UNITS ONLY)
NOTE: (A) MOUNTING SCREWS PASS THROUGH END
(B) RIGHT HAND SHOWN.
Insert slide shoe, rubber stop and end blocks
END BLOCK
Assemble track and attach to frame.
BLOCKS.
RUBBER STOP
stop, hold open mechanism, and end blocks into
and tighten securely. Insert slide shoe, rubber
Attach arm to slide shoe using screw supplied
track and attach track to frame.
IMPORTANT : L HINGE
C
NOTE: HOLD OPEN MECHANISM AND SLIDE SHOE MUST
BE INSTALLED WITH ARROWS POINTING AWAY
FROM THE DOOR HINGES. (ARROWS ARE
STAMPED ON SLIDE SHOE & HOLD OPEN
MECHANISM)
INSPK 08279350 Rev.09/09

control when extra time is required to pass through
Adjust sweep and latch valves.
Closing time from 90° to 15° (sweep range) is
generally adjusted to take a minimum of 3 seconds.
Closing time from 15° to fully closed (latch range)
should take a minimum of 1.5 seconds.
INCREASE
DECREASE
hex key.
INCREASE
the door. All valve adjustments are made with a 3/32"
Optional delayed action offers additional closing speed
DECREASE
CAUTION: DO NOT REMOVE VALVES.
NOTE: DELAYED ACTION IS AN OPTIONAL FEATURE.
RANGE
SWEEP
LATCH
RANGE
(INTENSITY)
BACKCHECK
POSITIONING VALVE
SWEEP & LATCH
DELAYED
ACTION
(TIME)
RANGE
LATCH
(SPEED)
SWEEP (SPEED)
BACKCHECK RANGE
DELAYED ACTION
BACKCHECK OR DELAYED ACTION
7
6
5Install main arm
onto top pinion. Fasten securely with pinion
With main arm parallel to door, place main arm
Rotate pinion 45° AWAY FROM HINGE edge of door.
Place wrench on bottom
pinion.
Adjust according to chart.
ADJUSTER
FULL TURNS
OF SPRING
0
+4
+12
FULL TURNS
OF SPRING
ADJUSTING NUT
ADJUST SPRING TENSION ACCORDING TO THE FOLLOWING CHART.
8916
8956
CLOSER
ULC LABELED UNITS ONLY
TYPE
200
200 6
5
60
SIZE
SPRING
DOOR
WEIGHT
150
125
MAX.
4
NON-BARRIER-FREE OPENINGS -
TYPE
8916
8956
CLOSER
INTERIOR
2'-6"
3'-6"
3'-0"
4'-0"
+4
0
+12
0
DOOR WIDTH
5
6
6
4
SPRING
SIZE
Take an opening force reading from
the pull on the door. If required, adjust the spring tension
to meet the barrier-free requirement. Maximum number of
adjusted to meet barrier-free forces may not have sufficient
power to reliably close and latch the door.
turns counter clockwise=8. Maximum number of turns
clockwise =14. Depending on opening conditions, a door
BARRIER-FREE OPENINGS -
8916 ONLY ADJUSTER
Adjust spring tension, if required, using a 1/4" wrench.
8956 supplied with size 6 setting.
8916 supplied with size 4 spring setting.
SPRING TENSION
CRITICAL
NOTE:
+
-
3'-6" +6 6+
+6
6+
250
LEFT HAND IS A MIRROR IMAGE.
INSTALLATION SHOWN.
NOTE: RIGHT HAND DOOR
PINION SCREW
PINION
6mm HEX KEY
C
L HINGE
45°
ROTATE
PINION 45°
Main Arm
(1)
QTY
08279351 2 of 3 09/09
INS NO. PAGE Rev.

Place tab in cover slot opposite main arm.
(2)
QTY
Place cover over closer and fasten securely with
screws provided.
NOTE: LEFT HAND INSTALLATION SHOWN. RIGHT
TAB
HAND IS A MIRROR IMAGE.
M2.5 HEX KEY
SNAP VALVE ADJUSTMENT
WRENCH INSIDE COVER
8
7
ON
To enable hold open,
push the white slide into
the hold open mechanism.
To disable hold open,
pull the white slide away
from hold open mechanism.
M2.5 HEX KEY
weaken force.
To adjust hold open
force, turn clockwise to
increase force, and
counter clockwise to
B
Set hold open.
AC
OFF
(HOLD OPEN UNITS ONLY)
Place the hold open
mechanism in desired
position and tighten screw.
08279351 3 of 3 09/09
INS NO. PAGE Rev.