DREAMS BRUGES KING B/S User manual

BRUGES KING B/S
Assembly Instructions
NOTE: It will require two people to assemble this bed. Assembly should be carried out in the room that
the bed will be used in.
1. We suggest you spend a short time reading through this leaflet and then
follow the simple step by step instructions.
2. If you follow the instructions carefully the end result should be worth the effort.
3. Do not discard any of the packaging until you have checked that you
have all the parts and the pack of fittings.
4. Assemble this product on a carpet.
5. To ensure an easier assembly, we strongly advise that all fittings are only
finger tightened during initial assembly. Only upon completion of the assembly
should all fixing points be fully tightened.
6. We recommend a periodic check on all fixing points to make sure they remain
fully tightened.
7. Keep glue and fittings out of children’s reach.
In the unlikely event that this product has missing or damaged parts, please call
0870 3333 612 to obtain spares
Before you
Start, here
is some
helpful advice
Minimum No. of people
Recommended to assemble
This product.
Approx assembly time:
Y
1 of 6

Component parts and fittings contained in the box
PARTS Fittings（A）
A
2 of 6
B
C
D
E
F
G
H
I
J
K
L
ON M
M6 JCN Nut 6pcs
Connector 4pcs
Connecting bolt 4pcs
Spanner 1pc
1
p
iece
1 piece
2 pieces
1 piece
1 piece
2 pieces
1 piece
M8Nut 4pcs
Ɏ8 Spring Washer 4pcs
M6x35mm Bolt 6pcs
4 pieces
4 pieces
4 pieces
4 pieces
4 pieces
2 pieces
ĭ10 Dowel 4pcs
M6x60 Bolt 12pcs
1
p
iece ĭ8 Dowel 16pcs
Locking Nut 16pcs
Locking Pin 16pcs
35mm Screw 19pcs
16mm Screw 6pcs
4MM Wrench 1pc

ASSEMBLY
3 of 6
1) Attachment of wooden leg to Head/footboard.
STEP 1
1) Attachment of center rails to side rails.
1) Attachment of short rails to center rails.
STEP 2
STEP 3

4 of 6
ASSEMBLY
1) Attachment of side rails to Head/footboard.
1) Attachment of side panel onto the back
panel.
1) Slide the bottom panel into the unit.
STEP 4
STEP 6
STEP 5

ASSEMBLY
5 of 6
1) Assembly of the frong panel onto side
frame.
ng panel onto
1) Slot in the Drawers.
NOTE:
Both slats on “step 9---step 12”
can be assembled to the
bedstead. Please follow the
correct procedure for the slat
system which you have chosen.
Sprung Slat System:
1）Adjust the support leg height to either
option 1-4, in accordance to the bedstead
height.
STEP 7
Select correct height for your bedstead
STEP 9
STEP 8
○
1○
2○
3○
4

ASSEMBLY
1) Use the pcs bolts, supplied with the
slat frame to fix the leg onto the slats
frame.
1) Carefully place the slat frame onto the
bed.
2）Use bolt (F) and JCN nut (G) to fix the
slat frame onto the bed.
Solid Slat System:
1) Carefully place the slat frame onto the
bed.
2）Use bolt (F) and JCN nut (G) to fix the
Slat frame onto the bed.
STEP 10
STEP 11
STEP 12
6 of 6