DREAMS Cooper Ottoman King Bed User manual

CooperOttomanKing Bed
AssemblyInstructions
1.Wesuggestyouspendashort timereadingthroughthisleafletandthenfollow
thesimplestep bystep instructions.
2.If youfollowtheinstructionscarefullythe end result shouldbe worththeeffort.
3.Donot discardanyof thepackaginguntilyouhavechecked that you
haveallthe partsandthepack offittings.
4.Assemblethisproduct onacarpet.
5.Toensureaneasier assembly, westronglyadvisethat all fittings areonly
finger tightened duringinitialassembly. Onlyuponcompletionof the.
Assemblyshouldallfixingpointsbe fullytightened.
6.Werecommendaperiodiccheckonallfixing pointstomakesuretheyremain
fullytightened.
7.Keep glueand fittings out ofchildrensreach.
Intheunlikelyeventthatthisproducthasmissingordamagedparts,pleasecall
03442 920000 toobtainspares
Beforeyou
Start, here
aresome
helpful
advices.
Revision number1/1

Revision number1/1
PARTS
Fittings
NO. PARTLISTQTY
(1)HEADBOARD1
(2)FOOTBOARD1
(3)SIDERAILS (R&L)2
(4)BOTTOM BOARDS2
(5)GAS LIFT(R&L)2
(6)SIDERAILSUPPORT2
(7)RAILS (R&L)2
(8)CENTERRAIL1
(9)CENTERRAILS2
(10)TUBINGSLATS2
(11)SLATS32
(12)FABRIC PULLHANDLE 1
A
C
I
J
L
K
M
M
8
2
0
mmx
16
pcs
B
M
6
2
5
mmx
12
pcs
M
8
30
mmx
6
pcs
D
M
6
40
mmx
18
pcs
E
M4
Allen key
1pc
F
M5Allen key 1pc
H
11
Spanner
1pc
M8
Washer x
22
pcs
M6
Washe
rx
36
pcs
M6
NUT
x
6
pcs
Centre Cap x16pcs
SideCap
x
3
2
pcs

ASSEMBLY
STEP1
Revision number1/1
(1). Usebolt (A),Washer(I)tofix
the Side rails3toHeadboard1
and Footboard2byusing Spanner
(F ).
F
MAKE CERTAINTHEBEDIS
SQUAREDUP,AS SHOWNON
THERIGHT.
Onceall fourcorners arelocated,
makesurethe bed isstill square
asin the sketch,then tighten all the
bolts100% using Allen key(D).

ASSEMBLY
STEP2
(1).AttachBottomBoards4.
Revision number1/1

ASSEMBLY
STEP3
(2). Usebolt (B),Washer(J)to
(2).fixthe GAS Lifts5to
Side Rail
3byusingAllen key(E). Bolts
fixing shouldbe in order
sequence: fit the round holefirst,
then fit others.
Revision number1/1
(4).Usebolt(C),Washer(I)tofix
the Side rail support6toSideRail
3byusingAllen key(F ).
(1). loosen thenut, then fixthe
gaslift.
ROUND HOLE
Right
Left
NOTE: Please fullytighten all
ofthescrewbefore nextstep.
(3). Usebolt (B) withWasher(J)
tofixthe Gaslift toSide Rail
support byusing Allen key(E).

ASSEMBLY
STEP4
Revision number1/1
1). Usebolt (B)(D), with
Washer(J) tofixthe CenterRail
89toTubing Slats10byusing
Allen key(E).
2). Usebolt (D), withWasher
(J) tofixthe L&RRails7toTubing
Slats10 byusing Allen key(E).
3).makesureholesforslats
capsarefacing upwards

ASSEMBLY
STEP5
(1).Usebolt(D),Washer(J) to
fixthe slatframetoGASLifts5by
using Allen key(E)and Spanner
(H). Boltsfixing should bein
ordersequence: fit the round hole
first, then fit others.
Revision number1/1
ROUND HOLE

ASSEMBLY
STEP6
(1).InsertSlats11toSideCap
(L)&CentreCap(M), afterwards
insert the Captothe holesof 2x
L&RRail7, CenterRail 9
Revision number1/1

ASSEMBLY
STEP7
(1).Attachthe FabricPull
Handle 12at the end of slat
frame, see picturebeside
Revision number1/1