DREAMS HAMPSTEAD BED User manual

DOUBLE 231-00029 (Solid slats)
231-00030 (Sprung slats)
HAMPSTEAD BED
Minimum No.of people
recommended to assemble
this product
Approx assembly time
Before you
start,here
is some
helpful advice
We suggest you spend a short time reading through this leaflet and1. then follow the simple step by step instructions.
If you follow the instructions carefully the end result should be worth2. the effort.
Do not discard any of the packaging until you have checked that you3. have all the parts and the pack of fittings.
To ensure an easier assembly, we strongly advise that all fittings are4. only finger tightened during initial assembly. Only upon completion of
the. Assembly should all fixing points be fully tightened.
We recommend a periodic check on all fixing points to make sure they5. remain fully tightened.
Keep glue and fittings out of children’s reach.6. In the unlikely event that this product has missing or damaged parts,7. please call 0844 292 0000 to obtain spares
Page 1 of 1227814400
Assembly Instruction

1
2
3
4
5
6
7
8
9
10
11
12 13
14
15
16
CHECK LIST Part
number Artical number Quantity Measure Dimention (mm) Quantity
1 32433944 1 1554x1210x110
2 32434044 1 1524x418x80
3 32434144 1 1920x395x104
4 32434244 1 1920x395x104
5 32432344 2 340x310x17
6 32432444 2 340x310x17
7 32432544 2 416x340x17
8 32432644 2 416x340x37
9 32434344 1 1354x310x19
10 32432844 1 500x260x17
11 32432944 1 500x260x17
12 32434444 1 1315x260x17
13 32434544 1 1325x481x8
14 324332 2 481x50x17
15 324346 1 1907x70x25
16 324334 2 316x70x25
Page 2 of 1227814400

8mm
6mm
Page 3 of 12
Note:The following fittings will be found in the box which contains the Sprung
Frame, NOT with the bed frames Assembly Kit.
PLEASE DO NOT USE THE FOLLOWING HARDWARE FOR THIS BED!
27814400
A
Ø10 x 40mm x 10pcs.
BC
DE
M8 x 65mm x 2pcs. Ø35 x 2pcs.
M8 x 2pcs. Spanner x 1pc.
Center leg x 1pc.
R
Support leg x 2pcs.
T
M6 x 12mm x 8pcs.
Allen key 4mm x 1pc.
F
G
M6 x 38mm x 6pcs.
H
S
I
Ø3.5 x 30mm x 16pcs.M6 x 22mm x 4pcs.
F
Allen key 4mm x 2pcs.
JKL
Ø3.5 x 16mm x 24pcs.12pcs.
M6 x 25mm x 24pcs.
MNO
M8 x 120mm x 4pcs. Ø12 x 15mm x 4pcs. M8 x 8pcs. (BIG)
P
M6 x 6pcs. (SMALL)
Q
60x22x22mm x 2pcs.
Fittings

4
Ax4
Ax1
Ix2
Q
Insert cam bolts "B" into
the footboard "2" by hand.
Insert dowels "A" into the
side rails "3" and "4".
Attach wooden blocks "Q"
to side rails "3" and "4",
insert screws "I" into
wooden blocks "Q", tighten
with a screwdriver.
Page 4 of 1227814400
B
2
B
46mm
3
Ax4
Ax1
Ix2
Q
Assembly

Page 5 of 1227814400
Fix the side rails "3" and "4"
to the headboard "1" and
footboard "2".
For the footboard, use
washers "C" and nuts "D"
to secure side rails "3" and
"4". Tighten using spanner
"E".
Insert screws "I" into
wooden blocks "Q", tighten
with a screwdriver.
For the headboard, use
bolts "M" and washers "O"
through the headboard and
nuts "N" in the side rails.
Tighten using spanner "E".
Dx2
Cx2
Ex1
Mx4
Ox4
Nx4
Fx1
Jx8
Attach front and back
panels "5" and "6", to top
and bottom panels "7" and
"8" using bolts "J".
Tighten using allen key "F".
Bedside Tables x 2
Ex1
1
23
4
Ix2
5
8
7
6

Lx8
Kx4
8
Install castors "K" to panel
"8", tighten with screws "L".
x2
Fx1
Jx4
Attach side panels "10" and
"11" to back panel "12"
using bolts "J".
Tighten using allen key "F".
Footboard Drawer
Page 6 of 1227814400
11
10
12

Page 7 of 1227814400
Slide in panel "13" along the
groove into the drawer
frame.
Locate supports "14" into
back panel "12".
Attach front panel "9" and
secure to side panels "10"
and "11" using bolts "J".
Tighten using allen key "F".
Fx1
Jx4
13
10
11
14
14
12
9
11
10
14
14

Secure supports "14" to
front panel "9" and back
panel "12" using screws "I".
Install castors "K" to body
of drawer, tighten with
screws "L".
Page 8 of 1227814400
14
9
12
14
Lx8
Kx4
Ix4

Page 9 of 1227814400
Attach central support "15"
to support feet "16".
Using bolts "G", tighten
using allen key "F".
Locate central support "15"
in between the headboard
"1" and footboard "2".
1
23
4
15
15
16
16
Fx1
Gx2

7mm
16
IMPORTANT
Once the feet have been
assembled and attached,
they should be adjusted to
ensure they do not touch
the floor, (7mm above the
floor) to allow for movement
once the mattress is placed
on the bed frame.
It is important to note that
when moving the bed that
it is not dragged into its new
position to prevent the
possibility of these feet
being twisted or angled to
one side, which could lead
to the collapse of the centre
of the bed.
To move the bed, remove
the mattress and lift the bed
into its new position to avoid
damage.
Ensure the feet are at 90 to
the floor before replacing
the mattress.
Place the fixed wood slats
onto the slat holders on
side rails "3" and "4".
Fix the slats at both ends
and the middle using screws
"I" and washers "P", tighten
with a screwdriver. total of
six screws and washers.
Option 1:
Dreams solid slats
Important Note: Your
Bedstead comes supplied as
standard with Solid Wood
Slats, or upgrade available to
Sprung Slat System at point
of purchase at an additional
cost.
Please carefully follow the
correct assembly instructions
for the slat system that you
have purchased.
Page 10 of 1227814400
1
23
4
Ix6
Px6