DREAMS Yardley Single Ottoman User manual

Yardley Single Ottoman
Assembly Instructions
Need assistance?
Call: 0344 292 0000
Dimensions mm Length Width Height
Single 2040 1010 910
Approximate time to
assemble this product
Retain these instructions
for future reference
2 x people recommended to
assemble this product
Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fixings.
You will require a cross
head screwdriver
Helpful advise before you begin:
1. We suggest you spend a short time reading through this leaflet
and then follow the simple step by step instructions.
2. If you follow the instructions carefully the end result should be
worth the effort.
3. Do not discard any of the packaging until you have checked that
you have all the parts and the pack of fittings.
4. Assemble this product on a carpet.
5. To ensure an easier assembly, we strongly advise that all fittings
are only finger tightened during initial assembly. Only upon
completion of the assembly should all fixing points be fully
tightened.
6. We recommend a periodic check on all fixing points to make
sure they remain fully tightened.
7. Keep glue and fittings out of children’s reach.
8. Do not use any other tools other than those recommended to
build this product.
9. Please do not use substitute parts. Use only additional or
replacement parts supplied by Dreams Ltd.
10. In the unlikely event that this product has missing or damaged
parts, please call 0344 292 0000 to obtain spares.
Page 1 of 7
1/2

Page 2 of 7
Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fixings.
Fittings Checklist
Parts Checklist
A
B
C
E
F
G
H
I
J
D
K
L
M
before assembly the bed, please open
the zipper at the back of headboard
and find the hardware pack(fittings A-R),
footboard(03),bottom cover(05) and bar
slats(10) here.
x1Strap
x8Bolts (M8x25)
x8Bolts (M8x20)
x2Metal Brackets
x8Bolts (M8x45)
x4Feet
x4
Nuts
x8
Nuts (M8)
x16Flat Washers (M8x20)
x4
Screws (Ø4x25)
x1Allen Key (M8)
x1Spanner (M8)
Black Soft Mat x2
Check size of fixings against this guage (dimensions in mm)
1 0 2 0 3 0 4 0 50 6 0 7 0 8 0 9 0 1 0 0 1 1 0
01
02
03
04
05
06
07

Page 3 of 7
Bed Frame Assembly
2
x 8
Bolts (M8x25)
B
Philips head screwdriver
ADDITIONAL TOOLS
(not supplied)
x 1
Allen Key (M8)
L
1
D
x 8
Bolts (M8x20) x 2 Metal Brackets
D
Black Soft Mat x 2
I
C
C
C
Loosely insert bolts (B) into each side of headboard (1) and foot board (2). Note: Do not tighten fully but leave 10mm
protruding.
Attach the side rails to the headboard and footboard. Make certain the bed is squared up, then tighten all bolts fully.
Attach the corner brackets to the headboard and footboard. Stick the black soft mat on the corner brackets.
01
01
02
02
02
02
03
04
04
04
B
B
B
B
I
L

Page 4 of 7
Bed Frame Assembly
4
3
Attach the fabric base to the bottom
before assembling the feet. Make
sure the fabric is fixed evenly all
around.
05
F
Don’t over tighten the screw
x 4
Feet x 4 Screws (Ø4x25)
FK
Use the cross head screw driver to fit the feet by following the white dots on the bottom of headboard and footboard.
Turn the bed on its side and attach the fabric base to the bottom of the side rails, headboard and footboard.
Note: Make sure the fabric is fixed evenly all around.
K

Page 5 of 7
E
x 8
Nuts (M8)
x 8
Bolts (M8x45)
E
x 16
Flat Washers (M8x20)
J
H
Lift up the slat frame by one person with two hands.
Another one assemble the gas lift with nuts.
Don't over tighten, a small gap is left so stem can
move freely.
Put the slat frame on the lift mechanism, use three sets of bolts (E), flat washers (J) and nuts (H) to loosely fit the
slat frame to the first four holes on each side of the lift nearest to the headboard, finger tight.
Lift up the slat frame, use the locking nut (G) to fit the pistons to the lift mechanism.
Note: A small gap is left so stem can move freely. This is normal, See the sketch.
SMALL GAP
x 4
Nuts (M8)
G
Bed Frame Assembly
6
5
J
J
H
M
G
G
07
When fully assembled and the
mattress is in position,
please raise & lower the
ottoman 4-5 times
To ensure the gas pistions are
fully lubricated
Do not fully tighten all the bolts before
confirming the metal frame is in correct
position. Frame must be in the center
of bed in length & width.
x 1
Spanner (M8)
M

A
x 1
Strap
A
Page 6 of 7
Bed Frame Assembly
7Wrap the handle strap to the frame as the diagram.
NOTE: When fully assembled and the mattress is in position,
please raise and lower the ottoman 4-5 times. To ensure the gas
pistons are fully lubricated.

Page 7 of 7
Care of your Dreams Furniture
Your new bed from Dreams is more than a beautiful piece of
furniture. It’s an investment in your health and wellbeing. Care
for it well and you’ll enjoy a great night’s sleep for many years
to come.
Should you have any issues with your product please contact
our customer service team on 0344 292 0000
On Delivery
Once your new bed is in place and all the packaging is removed,
let it air for approximately 1 hour before putting on your mattress,
mattress protector and bed linen.
Don’t worry if your bed feels a little strange at first. It takes time
for your body to adjust to a new level of support and comfort. You’ll
soon be enjoying a more relaxed sleep.
Please consider the surface your bed will be stood on. If your bed
frame is to be stood on an uncarpeted surface please ensure that
you use rubber backed mat under the legs to avoid slipping.
Day to day Care
Please use only 5% soap, 95% water solution, wiping with a damp
cloth. Finally dry with a soft clean cloth. Dust with a soft clean cloth
only.
Check all bolts, screws and legs regularly to make sure they
haven’t loosened and tighten all joins of your furniture or bedstead
after 6 months. Please keep these instructions in a safe place for
further use.
Storage Drawers in Bedsteads are designed to carry lightweight
items such as Pillows, duvets and linen. Please try to avoid storing
heavier items such as books or toys.
Returns
If you have bought a large item such as a bed or mattress which
is damaged or faulty and would like to return it, we will be able
to arrive at your home and take your item away. All we ask is that
your item is in perfect condition and in its original packaging (you
can open the packaging to inspect your item). Items will not be
able to be returned if they are not in their original packaging.
For online and telesales orders, you can only return an item within
14 days from the date of your delivery.
Dreams reserve the right to modify products, dimensions, parts and fixings whithout notification.
www.dreams.co.uk
Thank you for purchasing from
Need assistance?
Call: 0344 292 0000