DREAMS Abbey Bed Single User manual

Abbey Bed
Single
Two person
assembly
3/4 hour approx
assembly time

Thank you
Hello, thanks for choosing to purchase your bed from our company- you're now on your way to
creating a practical and stylish solution for your room. Before you begin building your bed,
please take a moment to read through the instructions and make sure that you've got all the
relevant parts listed on the following pages.
Assembly tips
Before you begin, it’s best to identify all parts and fittings to build your bed.
We advise laying these out on the floor to check you have everything, and
familiarising yourself before building.
We recommend that you build your new bed in the room you’d like it to
be located - this will help prevent any risk of damage to your newly built
sofa bed whilst moving it.
Top tip
Safety and care
It’s really important to ensure children and animals are kept away from the
assembly area, as there are small components used in this bed which could
present a choking hazard. All plastic and wrapping materials should also be
To keep your little ones busy, there is a colouring page inside the back cover.
Recycling
Please ensure that packaging is disposed of in a safe and environmentally
friendly way, and recycle where possible. Our assembly instructions are
printed on recycled paper. Please keep your assembly instructions safe
to refer back to in the future.
Abbey Bed - Assembly Guide - Page 2

Parts
1. Head Board x 1 pc □
2. Head Board legs x 2 pcs□
3. Foot Board x 1 pc □
4. Side Rail x 2 pcs□
Parts list
Abbey Bed - Assembly Guide - Page 3
2
2
3
4
1
Important infomation
4
The bed you have purchased comes with 3 different base options; solid slats, sprung slats or with
Sleepmotion. Please identify which base you have purchased as the assembly method may change.
If you have purchased solid or sprung slats please follow the instructions below in the current order.
If you have purchased a Sleepmotion base, please build the Sleepmotion base first following the
instructions provided in that box. Once the base is built please skip to page (insert page number here
to build your frame.

Fittings
Please check you have all the parts listed below with your product:
Abbey Bed - Assembly Guide - Page 4
Inner Bolt Rubber Washer (Ø24) Tapping Screw
(Ø5 x 43mm)
Center legs
Fx 6 Gx 8 Hx 1 Ix 1
Allen Key
Nx 2
Metal Washer (Ø21)
Ex 6
Bolt (M6 x 20mm) Bolt (M5 x 35mm) Bolt (M5 x 25mm) Metal Washer (Ø16)
A x 10 B x 4 C x 6 D x 14
0 1 2 3 4 5 6 7 8 9 1010 11 12 13 14 15 16 17 18 19cm
Tools required
Please check you have all these below:
Scissors
Cross head
screwdriver
Tape measure

Assembly
HEADBOARD ASSEMBLING
Attached Headboard Leg (2) to
the Headboard (1).
Fully tighten Bolt by Allen Key (N)
provided.
1
Abbey Bed - Assembly Guide - Page 5
Assembly
HEADBOARD & FOOTBOARD ASSEMBLING
To loosely tighten Bolts to Headboard (1)
and Footboard (3) using Bolt (A),
Metal Waher (D), Rubber Washer (G).
Left Bolt 10mm in out side in this step.
2
SIDE RAILS ASSEMBLING
Attached Side Rails (4) down to headboard
and Footboard before tighten Bolts.
After attached, fully tighten using Bolt (A),
Metal Waher (D), Rubber Washer (G).
3
D
A
G
N
10 mm
3
1
N
A
2
2
1
G
D
A
N
4
4

Assembly
SLAT SYSTEM ASSEMBLING
4
Abbey Bed - Assembly Guide - Page 6
Assembly
Identify the slat system your have purchased...
Sprung slat system
Turn to steps A
5
Standard wooden slat system
x1
Adjustable Foot
I
Turn to step B,C & D
6

Assembly
SLAT SYSTEM ASSEMBLING
Put the sprung slat system(5) on the bedframe,
Fully tighten using Bolt (B), Inner bolt (F),
Metal washer (D), Metal washer(E).
SLAT SYSTEM ASSEMBLING
Take out standard wooden slat sysem (6).
Take out Center legs (I), make sure the foot
can be adjustable.
A
Put the standard wooden slat sysem (6)
on the bedframe, fully tighten using
Bolt (C), Inner bolt (F), Metal washer (D),
and Metal washer(E).
B
Abbey Bed - Assembly Guide - Page 7
Assembly
E
F
C
D
N
N
6
F
E
N
x4
N
B
D
4
5
5
4

Assembly
Assembling center leg (I) to the slat sysem,
fully tighten Tapping Screw(H) using
cross screwdriver (Not provided).
Fit the adjustable support wooden leg
to the centre slat (there is a pre-drilled hole
on the centre slat) as shown.
C
Fully tighten using Bolt (C), Inner bolt (F),
Metal washer (D), and Metal washer(E).
D
Abbey Bed - Assembly Guide - Page 8
Assembly
E
F
C
D
N
N
I
H
Adjustable Foot
Fit the adjustable support wooden leg to the
centre slat (there is a pre-drilled hole on the
centre slat) as shown.
5

Abbey Bed - Care and maintenance - Page 9
Care and maintenance
Here are some tips to keep your new bed in tip-top condition
Cleaning
To clean your new bed, we'd advise using a warm damp cloth - please do not
use abrasive chemicals or bleach as this may damage the product.
Fabric
Please note depending on the lighting, positioning and surroundings of your
period of time, the colour might lighten or fade slightly due to light exposure.
Wood
Please note each of our wooden pieces are unique, meaning that markings and
shade can vary slightly between beds. Over a period of time, the wood might
lighten or fade slightly due to light exposure.
Metal
Metal tends to be more resilient to everyday wear and tear. We recommend to
gently dust your metal furniture and keep it dry to maintain its look.
Periodically we recommend you check that the screws or fixtures haven't been
become loose, over time. To move your new bed, we recommend lifting it where
possible, as dragging or pushing it could cause damage to your flooring.
Checking and moving
Thank you for shopping with us - we hope you have
a great night's sleep

Little dreamers
Keep the little ones entertained while
you assemble your new purchase.