DREAMS Messina Bedstead User manual

3
3
*Only supplied if upgraded sprung system chosen
5
6
14
MESSINA BEDSTEAD
Parts Identification
PLEASE READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in a
safe environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be kept
a way from young children whilst assembling your unit to
avoid the danger of choking hazards.
Qty
1
2
3
4
5
6
Headboard
Footboard
Leg
Side Rail
1
1
4
2
Wooden Slats
Metal Sprung Slat System*
1 Set
1 Frame
Parts Checklist
Ref.Description
Note:
Standard wooden slat frame (part 5)
Upgraded sprung slat frame (part 6)
1
2
3
4
3
4
Page 1 of 4

QtyCode Description
In the unlikely event of missing or damaged parts, please
contact the customer service team on 08442 920000.
When
calling this number, please quote the part code
reference numbers shown in this leaflet when
requesting spare or replacement parts.
This
assembly requires two
people.
Ax8
Bolt (M8x30mm)
Fittings Checklist
C
x8
Spring Washer
D
x8
Washer (17x8mm)
Additional Tools Required
H
x1
Allen Key (4mm)
Fx6
Sleeve Nut (M6x15mm)
QtyCode Description
B
Bolt (M6x40mm) x6
General Hints & Tips
When fitting barrel nuts into
the
panels, ensure they are
fitted
the correct way so the
hole is facing towards the
intersecting hole.
Intersecting
Hole
Care & Maintenance
Long Crosshead (Pozi) Screwdriver
We recommend the bed is
assembled
in the room it will
be located in.
I
x6
FlatWasher (6mm)
G
Screw (4x25mm) x16
E
Allen Key (5mm) x1
JBolt (M6x15mm) x8
Note: The following fittLQJV will be found in the box which contains the Sprung Slat Frame. 7KH\DUH not in the main
KDUGZDUHSDFNRI the bed itself.
K
Support Leg
L
CentrHSupport Leg
x2
x1
Page 2 of 4
check that all bolts are still tight.
Please
retain your Assembly Instruction and
tools provided, for future use. Periodically

Bed Assembly
Stage
1
Ax8 Bx8 Cx8
x16
H
Fit the bolts (A), spring washers (B), and washers (C) to the holes in the headboard (1) and footboard
(2) as shown. Note: Do not fully locate the bolts, but leave 10mm protruding.
Fit the side rail (4) to the headboard and footboard locating the brackets over the bolt heads.
Once all four corners are located, PDNHVXUHWKHEHGLVVTXDUHWKHQtighten the bolts using DOlen key (D).
1
4
A
B
C
10mm
2
1
Stage
2
12
&
3
H
Fix legs (3) in the marked positions, on underside of headboard (1) and footboard (2).
1
2
4
4
Page 3 of 4

Use all of the x6 sets provided (E, F & G).
Use x4 of the x6 sets provided (E, F & G).
Bed Assembly
Stage
2a
UPGRADE SPRUNG SLAT SYSTEM
6
6
Gx4
Fx4
Ex4
Jx8
6
L
K
L
Stage
2
BED SLAT FIXING Gx6
Fx6
Ex6
5
5
Lay the set of slats (5) onto the slat
support rails on the side rails.
Align the first and last slat with the
end of the rails, and secure in place
using the bolts (E), washers (G) and
sleeve nuts (F). Fully tighten using
the allen key (I).
Once secure fix the centre slat using
the bolts as before.
Open the metal frame and lay face down on the working
surface.
Fit the support legs (K & L) to the positions shown, securing
with the bolts (J). Fully tighten using the allen key (I).
Carefully turn the slat frame over, and position onto the slat
support rails. Align the frame with the fixing holes at each
end and secure using the bolts (E), washers (G) and sleeve
nuts (F). Fully tighten using the allen key (I).
Finally, please ensure that all bolts are fully tightened
before the bed is used.
(,7+(5 5 OR 6 WILL BE SUPPLIED %2;('SEPARATE/<
5
Page 4 of 4
6