DREAMS TRAFALGAR User manual

Parts Identification
Parts Checklist
Page 1 of 13
4
3
2
*Only supplied if upgraded sprung slat frame system chosen
Legs (9&10) only supplied with sprung system
TRAFALGAR TV-AUDIO BED
Double, King & Super King sizes
160407
PLEASE READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be kept
away from young children during assembly, to avoid the
danger of choking.
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY.
Note:Standard wooden slat frame (part 6)
Upgraded sprung slat frame (part 8)
1
67
8910
5a 5b
11
12 13
14
15
15 16
18
19
17 17
20
23
b
21
22
21
24
27
28
26
25
Qty Qty
Ref. Description DescriptionRef.
1
2
3
4
7
6
5a&5b
8
9
10
11
1
1
1
1
1
1
1
2
1
Media Tray Base Panel
Media Tray Side Panel-L
Media Tray Side Panel-R
Media Tray Back Panel
Media Tray Support Legs
1
12
13
14
28
16
17
18
19
20
21
22
*Upgraded Sprung Slat Frame*
1 Pr
1
1
1
3
1
3
Drawer Face Panel
Drawer Side Panels
Drawer Front Panel
Drawer Back Panel
Drawer Bottom Panel
Drawer Bottom Support Rails (Ends)
Drawer Bottom Support Rail (Centre)
Mains Power Lead - 3 metre
Aerial Lead - 4 metre
HDMI Leads
Cable Ties
Cable Clips
Remo 2.10 User Manual
90º Adaptor
15
2
2
1
1
1
2
1
Headboard
Footboard
Side Panel - Left
Side Panel - Right
Adjustable Support Legs
Wooden Slat Set
Wooden Slat Set Support Leg
*Sprung Slat Frame Centre Support Leg*
*Sprung Slat Frame Support Legs*
23
24
25
26
27
1
1
Inside
accessory
box
e
1
e
1
2

QtyCode Description
Ax16
Fittings Checklist
D
x16
Spring Washers (for M8 bolts)
E
Flat Washers (for M8 bolts)
Qty
Code Description
C
B
Allen Key (for M8 bolt) x1
x4
Bolts (M8x30mm) for
fitting side panels (3&4)
to headboard & footboard (1&2)
Screws (3x20mm) for fitting
wheels (S) to drawer bottom
support rails
Screws (4x30mm) for fitting
drawer face panel (16)
SDrawer Wheels x5
Bolts (M8x45mm) for
fitting adjustable support
legs (5) to side panel (3)
x4
M x6
Spring Washers (for M6 bolts)
EXTRA HARDWARE NEEDED WHEN FITTING UPGRADED SPRUNG SLAT FRAME
Note: The following fittings will be found in the box which contains the upgraded metal frame itself.
Qty
HARDWARE FOR FITTING WOOD SLATS OR UPGRADED SPRUNG SLAT FRAME (PACK B)
Jx1
Allen Key (for M6 bolt)
G x6
Sleeve Nuts - M6
Bolts (M6x40mm) for
fitting the wooden slat set (6)
or the sprung slat frame (8) to
side panels (3&4)
x6
x7
Flat Washers (for M6 bolts & 5mm screw)
H
F
Screw (5x50mm) for
fitting slat suport leg (7)
K x1
HARDWARE NEEDED FOR BED ASSEMBLY (PACK A)
Qty
Code
WHEELS FOR DRAWER (PACK D)
Screws (5x50mm) for
assembling drawer panels
Description
a
x20
QtyCode Description
Ax6
Q
x20 R
Qty
Code Description
N
P
Plastic Barrel Nuts
x27
Bolts (M8x30mm) for
dna)51(sgelyartadiemgnittif
fitting media tray to side panel (3)
x27
HARDWARE NEEDED FOR DRAWER & MEDIA TRAY ASSEMBLY (PACK C)
x8
Code Description Qty Code Description
DFlat Washers (for M8 bolts) x4
Page 2 of 13
TV INSTALLATION KIT - Inside Pack (A)
Bolt Sets (M6x25mm)
L
Bolts (M6x15mm) for fitting
support legs (9&10) to the
sprung slat frame (8)
x8 9
Sprung slat frame
centre support leg
Sprung slat frame support legs
x1
10 x2
b
x1c Allen Key for Lid-Lifter - 2.5mm
x1
d Spanner (for 9mm Domed Nut)
x6
Self-Adhesive Pads - 3mm
(are inside accessory box) x1
e HDMI 90º Adaptor

In the unlikely event of missing or damaged parts, please
contact the customer service team on 0344 292 00 00.
When calling this number, please quote the part code
reference numbers shown in this leaflet when
requesting spare or replacement parts.
Please retain your assembly instruction and
tools provided for future use.
Periodically check that all bolts are still tight.
Additional Tools Required
General Hints & Tips When they are supplied and are
part of the assembly of this bed,
ensure that the barrel nuts are
fitted the correct way so the
hole in the nut is facing towards
the intersecting hole in the panel.
Intersecting
Hole
Care & Maintenance
Cross-head Screwdriver
We recommend the bed is
assembled in
the room it shall be
located in.
Page 3 of 13
Stage
1
B D
ARROWS ON LABELS POINT
TOWARDS EACH OTHER
D
B
3
Bed Assembly - Use Pack 'A'
x4 x4
5b
E
x1
Fix support legs (5) from inside the bed
into the pre-threaded holes in the side
panel (3) using bolts (B) & flat washers (D).
Make certain the labels are as shown in
the diagrams - they must point towards
each other. The legs are then in correct
place to stop the drawer going under the
bed. Tighten with Allen key (E).
Carefully adjust feet clockwise so they just touch the floor
keeping side panels level when bed is in use.
B
D
5a
Adjustable Feet
A ssembly requires two persons.
Approximate time to
assemble this product
1.5 HRS

Stage
2
42
x16 x16 x16
x1
A
C D E
Note: Do not tighten fully but leave 10mm protruding as in the diagram.
A
C
D
i) Fit bolts to headboard &
footboard (1&2) like this.
1
2
b.
3
4
&
&
3
4
&
Bed Assembly - Use Pack 'A'
iii) Once all four corners are located, make sure the bed is square
as in the sketch,
then tighten all the bolts 100% using Allen key (E).
1
Page 4 of 13
3
ii) Fit the side panels
locating the brackets
behind the flat washers.
Loosely insert four sets of bolts (A) with spring washers (C) & flat washers (D) into each side of headboard &
footboard (1&2).
a.
10mm

Stage
3
14
14
12
13
11
Px13 Rx13
Fit the barrel nuts (R) to the media tray back panel
(14), making sure the screw hole in the nut aligns
with the intersecting hole in the panel (see hints &
tips section).
Fit the side panels (12&13 ) to the back panel (14)
using the screws (P) into the barrel nuts.
Fit barrel nuts (R) to the inside faces of the tray
side panels as shown.
Fit the tray base panel (11) using the screws (P) to
secure through into the barrel nuts previously fitted.
Stage
4
15
A
x2
Fit the support legs (15) to the underside of
the media tray base panel using the bolts (A).
Tighten bolts using the Allen key (E).
Media Tray Assembly- Use Pack 'C'
Media Tray Assembly - Use Pack 'C'
x1E
A
R
R
R
A
Page 5 of 13
P
P
P
P
P
P
P
P
P
P
P
P
P

Stage
5
A x4 D x4
Push bolts (A) through flat washers (D).
Hold tray firmly against side panel (4) as shown and screw in x4 bolts.
When all screwed in place, tighten bolts 100%.
Adjust the adjustable feet in support legs (15) so bottom of tray is level.
4
Media Tray Fitting - Use Pack 'C'
Electrical & Cable Connections
Stage
6
FOOTBOARD
2
2
3MT Mains Power Lead
23
1
3
4
Page 6 of 13
x1E
TV Mounting Column (W)
Manual Raise & Lower
Buttons.
Connect the Mains Power Lead (23) into
the 3 Pin socket located on the right-hand
side at bottom of the footboard (2).
Connect UK plug to your wall socket.
Note that the power supply to this plug
must be earthed.
The plug must be easy to reach if you
need to disconnect the power at any time.
To operate the TV Mounting Column (W) there is a switch (V) in
each side panel of the bed near the headboard (1).
The switches are connected to the TV Lift control system by DIN
plugs on each side of the footboard (2) - make sure they are
plugged in properly - align the arrows on the labels and push right in.
Clip the wires to the plastic blocks to keep them tidy.
One can now operate the TV Lift.
V
DIN plugs
switch (V)
Note: If you press the Up or Down button in quick succession (1 Min) ,
the TV Lift does not move - this is normal, just press the button twice.
Keep wires tidy - peel off
pads from clips & adhere
to plastic blocks.
3
&
4
2

Stage
7
Stage
8
SUPPLIED & PACKED IN THE ACCESSORY BOX
MEDIA CONNECTION LEADS
TV Mounting Column (W).
Max load is 12 kg.
Max dimensions of TV that can be
fitted: 82 x 6.5 x 43.5cm (WDH)
4Mt
Aerial Lead
Cable Clips
Cable Ties
2.8 Mt HDMI
i) Place TV on Platform (Y) as in sketch.
Occasionally the remote control eye or on/off switch
is mounted underneath the TV so please make sure
they can be operated correctly. It may be necessary
raise height of TV by using extra pads (b).
Page 7 of 13
Power Lead
Supplied with TV
Self-Adhesive
Pads (b)
TV Installation Kit - Separate bag in Pack (A)
iii) If necessary, adjust mounting plates (X) by loosening the four domed
nuts (Z) and move plates up or down so bolts (a) are in line with the
VESA fixing holes on back of TV then tighten with spanner (d).
After final fitting of the TV, adjust lid-lifter back down so curve is 3mm
higher than top of TV.
ii) If TV height adjustment is necessary,
Adjust lid-lifter to maximum height of the
slot using Allen key (c) - loosen the
clamping screws (don't remove) & slide
curved lifter to top of it's slots. Gently lock.
c
a
J
(X)
(Z)
(Y)
CONNECT CABLES CAREFULLY.
USE CABLE TIES & CABLE CLIPS TO KEEP ALL LEADS TIGHT
AS CLOSE TO BACK OF TV AS POSSIBLE - MAKE SURE THERE
ARE NO LOOSE WIRES THAT COULD BECOME TRAPPED.
24
Note: To fix TV, use the M6x25mm bolts &
washers (a) from the TV Installation kit that is
packed with the main hardware kit - this kit is
packed inside the accessory box. Use Allen
key (J) but do not overtighten.
Please make certain that the 3.5mm black 90 deg
AUX plug is put into the HEADPHONE socket on
the rear of TV and NOT in another socket by mistake.
This shall route sound from TV to the bed speakers via
AUX Mode on the Remo 2.10 console (Green light).
24 25
Use cable clip (27) on back of TV
to keep leads tight - make sure all
leads at rear of TV go into the
ducts and cannot get trapped
IDENTIFY HEADPHONE SOCKET
LIFT 3.5mm PLUG & PUT INTO
HEADPHONE SOCKET. IF
NECESSARY, CLIP LEAD TO BACK
OF TV SO IT CANNOT SNAG.
x4
aBolt Sets (M6x25mm)
b
x1
cAllen Key for Lid-Lifter - 2.5mm
x1
d
Spanner (for 9mm Domed Nut)
x6
Self-Adhesive Pads - 3mm
(are inside accessory box)
ex1
HDMI 90º Adaptor
Leads - x2 + 90º
Adaptor
27
26
(W)
REMO 2.10
Audio System

Stage
9
HDMI Leads
& 90ºAdaptor
25
24
23
24
Page 8 of 13
Cable Connections
RIGHT DUCT
LEFT DUCT
Pass the TV Power Lead & Media Leads through the LEFT or
RIGHT duct. Choose the duct to suit connections on your TV.
Never pass cables in front of or behind the TV otherwise they
shall get trapped.
One Aerial Lead (24) & two HDMI Leads (25) with one 90º
adaptor (e) are supplied in the accessory box, use the
adaptor if required.
You can fit your own media cables as well but the ducts,
cable clips (26) & cable ties (27) must be used to prevent
any wires becoming trapped.
Note: Power socket for the TV is not to be used for any other
equipment because it is not permanent.
It cuts off power to TV when TV is down in the starting
position. When TV raises up, power is restored automatically.
Plug in TV
Aerial Lead
25&e
Power lead supplied
with your TV.

H x7
G
M
x6
x6
K
x6
x1x1
Page 9 of 13
i)
ii)
iv)
iii)
H
K
Adjustable foot
6
F
M
G
H
iii)
Fit slat support leg (7) to underside
of centre slat using screw (K) & flat
washer (H). Fully tighten with cross-
head screwdriver. Carefully turn
adjustable foot clockwise until it just
touches the floor and slat is
horizontal.
6
6
F
M
G
H
6
7
F
M
G
H
iv) Roll out rest of wooden slats
and fix with the last two bolt
sets. Fully tighten using
Allen key (J).
i)
Using two bolts (F) with spring
washers (M), flat washers (H) and
sleeve nuts (G) loosely fix first slat
next to the headboard.
ii) Roll out the slats to just over
halfway down the bed so centre
slat can be fixed in position. Use
two more bolt sets and loosely fix
the slat.
Align slats then fix all bolt sets
100% using Allen key (J).
J
Fitting Wooden Slat Set - Use Pack 'B'
Stage
10a
F
Carefully lay the wooden slat
set on the metal supports, on
each side panel.

Fitting Sprung Slat Frame - Use Pack 'B'
Stage
10b
H x4G x4
Fx4
M x4
J
x1
L
L
LL
L
L
Lx8
10
9
10
8
F
G
H
M
8
Page 10 of 13
8
Open the metal slat frame (8) and lay face down on a flat working
surface. Fit the support legs (9 &10 ) into the positions shown.
Secure with the bolts (L) then tighten 100% using Allen key (J).
Carefully turn the slat frame over and position onto
the metal slat supports, on each side panel of the bed.
Align the frame with the fixing holes at each end and
secure using four bolt sets comprising bolts (F), spring
washers (M), flat washers (H) and sleeve-nuts (G).
When all in place tighten using Allen key (J).
Finally, please check carefully that
all slat fixing bolts are tightened
100%, before using the bed.
9
8
10
10