DT Research DT313SC-MD Assembly instructions

Mobile Tablet
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright © 2019, DT Research, Inc. All Rights Reserved. BOG1015 DT313SC-MD/ DT313T-MD ENG
INTRODUCTION
Thank you for acquiring the DT313SC-MD/ DT313T-MD, part of DT Research’s line
of rugged tablets. Featuring a slim, robust enclosure, the DT313SC-MD/ DT313T-
MD with a 13.3” TFT display is powered by the Intel® processor, offering opmal
combinaons of performance and power savings.
The DT313SC-MD/ DT313T-MD is available with Microso® Windows® operang
system. Each soware operang system features web browser, client/ server
compung soware, media player, accessories, and applicaons support.
PACKAGE CONTENTS
• One DT313SC-MD/ DT313T-MD with Baery Pack and Handstrap
• AC-DC Power Adapter with Power Cord
• Basic Operaon Guide
DT313SC-MD/ DT313T-MD
* If your DT313SC-MD/ DT313T-MD contains Barcode Scanner or Front/Back Camera
modules, please refer to the Tablet Modules Basic Operaon Guide for detailed
operaon.

2 3
PRECAUTIONS
• Always exercise care when operang and handling the DT313SC-MD/ DT313T-MD
• Do NOT apply excessive pressure to the display screen.
• We recommend using the Digital Pen (oponal) to keep the screen clean.
• Avoid prolonged exposure of the display panel to any strong heat source.
Wherever possible, the DT313SC-MD/ DT313T-MD should face away from direct
light to reduce glare.
• If the AC-DC power adapter is used to recharge or power the tablet, do NOT use
any AC-DC adapter other than the one provided or acquired from the manufac-
turer or its partners.
• In the unlikely event that smoke, abnormal noise, or strange odor is present,
immediately power off the DT313SC-MD/ DT313T-MD and disconnect all power
sources. Report the problem to your device provider immediately.
• Never aempt to disassemble the DT313SC-MD/ DT313T-MD, as this will void the
warranty.
BASIC FEATURES
The DT313SC-MD/ DT313T-MD wireless tablet integrates a bright and mul-touch
display, one USB port, and embedded networking elements such as wireless LAN
and Bluetooth. The DT313SC-MD/ DT313T-MD is complemented by a suite of
accessories, including baery expansion, charging cradles, and baery charger kit,
for a comprehensive user experience.
A DT313SC-MD/ DT313T-MD typically integrates an 802.11ac wireless LAN (WLAN)
adapter that may connect to other wireless devices or access points. If your
DT313SC-MD/ DT313T-MD does not come with such a network adapter, please
consult your device provider to establish the desired network connecvity.
Power/Battery LED Status:
• Blue indicates the baery is 25% to 100% charged
• Blinking blue indicates the baery is charging
• Orange indicates that the baery is between 11% to 25%
• Blinking Orange indicates that the baery is below 10%
Button Functions
BUTTON ACTION
Programmable Buon
Power Buon
Trigger buon
Baery Latch
Input/ Output Ports
Ethernet Port
HDMI-out
USB 2.0 Ports
Headphone-out
USB 3.0 Port
DC-in
1
2
3
4
A
B
C
D
F
E
Baery/Power LED
1
2
4
3
B
A
C
D
E
F

Start Up
If the power up (from Standby mode or otherwise) is successful, the appropriate
interface will be displayed aer a launch sequence of several seconds. The wireless
LAN connecon may take 10-15 seconds to be established.
Configuring the Mobile Tablet
The DT313SC-MD/ DT313T-MD may be congured using the ulies and methods
dictated by the soware operang system. The DT313SC-MD/ DT313T-MD should
be congurable for various properes such as user proles, network features, and
several system elements.
Wireless Networking
Wireless LAN
The DT313SC-MD/ DT313T-MD is oen delivered with an embedded (user-
inaccessible) 802.11ac WLAN adapter equipped with a hidden custom antenna.
• Through the support of typical WLAN adapters, the DT313SC-MD/ DT313T-MD
should be able to detect all 802.11 access points in the vicinity for you to select
the access point of your choice for connecon.
• The SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT313SC-MD/
DT313T-MD and the access points have to match. The SSID is case-sensive and
it is recommended that you enable WEP/WPA/WPA2 encrypon (or advanced
alternaves) for secure access.
• When WEP/WPA/WPA2 is enabled, you may need to consult your network
administrator or your networking equipment literature to properly congure
associated sengs such as Authencaon mode, etc.
• Refer to the access point operang manuals for seng up the 802.11 access
points.
Bluetooth
The DT313SC-MD/ DT313T-MD offers the Bluetooth module which supports
Bluetooth 4.0 standard including Bluetooth 3.0 High Speed and Bluetooth 4.0 Low
Energy, which delivers faster speeds (up to 300 Mbps) with low power consumpon.
OPERATION
Powering ON and OFF
To acvate the DT313SC-MD/ DT313T-MD, push and quickly release the Power Buon.
The display will come on in a few seconds. To put the DT313SC-MD/ DT313T-MD in
Standby mode, push and quickly release the Power Buon. To turn the DT313SC-MD/
DT313T-MD off for extended storage, power off safely using any soware funcon that
“shuts down computer” provided in the soware operang system.
NOTE:
The baery packs shipped with your tablet may be low in power—please use
the AC-DC adapter with the DT313SC-MD/ DT313T-MD when seng up for the
rst me to fully charge the internal baery pack. You may charge the external
baery pack with it aached to the DT313SC-MD/ DT313T-MD, or with the
oponal external baery charger kit.
NOTE:
When the baerypack(s) is (are) charging, the blue-colored Baery LED should
blink slowly. If plugging in the AC-DC adapter does not trigger this blinking
acvity and the LED stays dark, the baery pack(s) may have been drained
substanally. Try unplugging/ replugging the AC-DC adapter to the DT313SC-
MD/ DT313T-MD a few mes to acvate the charging process.
NOTE:
To conserve power, use (push and quick release) the Power Buon to put the
tablet in “Standby” mode while not in use. Pushing briey on the same buon
will wake up the system within seconds.
NOTE:
Avoid using the Power Buon (“hold 4+ seconds” feature) to turn off the
tablet—this form of hardware shutdown is intended to be a means of recovery
from lockups, and not as normal operaon.
45

USING THE MOBILE TABLET
Peripherals Support
Through its USB port, the DT313SC-MD/ DT313T-MD supports a wide range of
USB-based peripherals. These peripherals are applicable for soware installaon,
applicaons storage, data storage, and system soware recovery and updates.
For More Support
Users can download the Tablet Modules Basic Operaon Guides from the DT
Research website.
67
To Hold the Tablet
Le hand: grip the le back side of the tablet
with your le hand four index ngers, with
thumb resng on the top of the back side of the
tablet and palm securely against the back.
Right hand: grip the right back side of the tablet
with your right hand four index ngers, with
thumb resng on the top of the back side of the
tablet and palm securely against the back.
Federal Communication Commission Interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protecon against harmful interference in
a residenal installaon. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Cauon: Any changes or modicaons not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules.
Operaon is subject to the following two condions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operaon.
This device and its antenna(s) must not be co-located or operang in
conjuncon with any other antenna or transmier.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.