DURAVIT Architec 700353 User manual

Mounting instructions Alcove Installation
Leben im Bad
Living bathrooms
Architec

2 Architec_US_.14.11.18
Architec
# 700353
# 700354
# 700355
# 700356

Architec_US_.14.11.18 3
en
Important information 4
Installation
Waste and Overflow installation
Cleaning and Care
6
8
10

4 Architec_US_.14.11.18
Important information
Regarding the mounting instructions
These mounting instructions comes as part of the Duravit
bathtub and should be read carefully prior to installation.
Explanation of key words and symbols
NOTE! In the case of potential damage to property
Link to installation information in this section
Inspection (e.g. for scratches)
Indication of the length of time (e.g. 10 minutes)
Inspect to check for leaks and tightness
Target group and qualification
The bathtub must only be installed by licensed plumber.
Note!
Local installation regulations and any country-specific
standards must be observed at all times.
Prerequisites
Please check door width(s) and ensure that the
bathtub can be easily transported into bathroom.
We reserve the right to make technical improvements
and enhance the appearance of the products shown.
Products are in compliance with following codes:
Uniform Plumbing Code
National Plumbing Code of Canada
International Plumbing Code
Products are in Compliance with the following standards
CSA B45.5-11/IAPMO Z124-2011
en

Architec_US_.14.11.18 5
# 791224
# 700353
# 700354
# 700355
# 700355

6 Architec_US_.14.11.18
1
x6
Inspect tub for any potential damage that
may have occured during transport.
Place cardboard or blanket on the floor and
turn tub over.
Connect tub waste and overflow.
Fatal injury by electric shock. Make sure
that there are no electrical wires or heating
running under the floor, which could be
affected by the installation of tub.
Affix 6 flange clips to the wall frame for side
support of the tub.
Set tub into designated frame area and
connect tub drain to rough in. Fill the tub
with water and inspect for any potential
leaks.
13
1
4
2
5
3
6
DANGER!

Architec_US_.14.11.18 7
Once tub is set, finish wall and tile and apply
silicone as needed.
7

8 Architec_US_.14.11.18
A
A
1
2
2-1/2"
(62.75)
1
2
3
4
6
5
1
2
“Click”
« Clic »
“Clic”
“Click”
« Clic »
“Clic”
B
B
1
2
Measure vertical distance of overflow to
drain and cut pipe length.
Measure horizontal distance of drain center
to overflow and cut drain pipe to match
length.
Attach rubber gasket and install the
overflow against interior of wall.
Using provide tool, attach to chrome trim
piece and connect to overflow. Turn tool
Clockwise to tighten into place.
Insert push button into yellow sleeve, turn
90° to secure button into place.
Insert push button and sleeve to overflow
and ensure button lines up with insert in
overflow.
Waste & Overflow Installation
1
4
2
5
3
6

Architec_US_.14.11.18 9
90° “Click”
« Clic »
“Clic”
1
2
3
1
2
3
4
5
6
1
2
3
4
Hand snug tight
(5 ft-lbs max)
Serrer à fond à la
main (5 pi-lb max)
Apretar bien sólo
con la mano
(5 pies/lb
máximo)
Once set, turn sleeve 90 degrees to secure
push button to overflow and then remove
yellow sleeve.
Connect drain and overflow using gasket and
adaptor.
Using provided gaskets, attach the drain to
the tub and insert get screw to drain.
Tighten set screw in drain using provided
tool.
Connect cable and ensure it is tight. It cannot
have slack.
Insert drain cover to drain and press
overflow button to actuate a sync.
7
10
8
11
9
12

10 Architec_US_.14.11.18
Cleaning and Care
ACRYLIC
Surface cleaning
Clean the surface with a soft cloth and soapy water. Do not use abrasive
cleaning liquids. For removing stains we advise using the Duravit care kit
for acrylic surfaces (see picture I).
More resistant stains can also be removed with warm water and a mild,
liquid detergent or soap sud.
Lime stain
Lime stains can be taken off with brandy vinegar and water. After treatment
rinse with clear water.
Damage
Cleaning substances other than those recommended by Duravit can
cause damage the material. Scratches and other superficial damage
can be corrected using the Duravit care and maintenance kit for acrylic
surfaces (see picture II).
I
# 790301 00 0 00 0000
Care kit
II
# 790302 00 0 00 0000
I: Incudes: Acrylic care agent, grinding paste, polishing paste, polishing cloth, and wet abrasive paper in various
grits.
II: Includes: Acrylic care agent, acrlic resin, resin hardener, stirring stick, grinding paste, polishing paste,
polishing cloth, and wet abrasive paper in various grits. (Resin only necessary for repair of air injectors.)
Care Kits can be purchased online through one of the certified parts distributors listed on our website:
http://www.duravit.us/website/homepage/service/parts.us-en.html
or
http://www.duravit.us/website/homepage/service/find_a_retailer.com-en.html
(If you cannot access the above link, go to www.duravit.us and click on the Service tab at the top. Then click Find a
Retailer in the left column.)