DXV Rem D3510045C User manual

- 1 -
INSTALLATION INSTRUCTIONS
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
SAVE FOR FUTURE USE
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
M965701 Rev. 1.1 (5/17)
Lever Handles
Model D3510045C
To be used with D35000450.191
Dual Control Wall Mount Lavatory Rough
Rem®
Trim Kit for Wall-Mounted
Vessel Lavatory Faucet
Plumbers' Putty or CaulkingAdjustable Wrench
Phillips Screwdriver
Flat Blade ScrewdriverChannel Locks Teon Tape
ROUGHING-IN DIMENSIONS:
• For reference
2" D.
(51 mm)
1-5/8" (41 mm)
1/2"
(13 mm)
1-1/2"
(37 mm)
2-3/4"
(70 mm)
8"
(203 mm)
11"
(279 mm)
1-7/8"
(48 mm)
1/2" NPT
UNION INLETS
1-5/8"-2-1/2"
(41 to 62 mm) FINISHED
WALL
FINISHED WALL
8"
(203 mm)
4"
(102 mm)
8-1/2"
(215 mm)
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.

- 2 - M965701 Rev. 1.1 (5/17)
1
2INSTALL VALVE BODY
• Mount VALVE BODY (1) to WALL BRACKET (2) as shown. Level and tighten SET SCREWS (3) to secure
VALVE BODY (1) to WALL BRACKET (2).
• Connect HOT water supply to LEFT INLET UNION (4) and COLD water supply to RIGHT INLET UNION (5).
Pipe connections are 1/2" NPT. Use sealant or Teon tape on pipe connections. Do not solder directly to valve body.
• With valves closed open supply lines and check for leaks. Remove PLASTER GUARDS (6) and open both
valves and check for leaks.
• Close both valves and turn off water supplies. Replace PLASTER GUARDS (6) and nish wall construction.
• Determine where the nished wall location will be. This measurement is very important! Note: The rough-in measurement
from the nished wall is; 1-9/16" (40 mm) minimum and 2-7/16" (62 mm) maximum. This is a 7/8" (22 mm) tolerance.
See rough-in illustration above.
• Secure WALL BRACKET (1) to cross brace of wall structure at required height using six wood screws.
INSTALL WALL BRACKET
WOOD SCREWS
CROSS BRACE
WALL STUDS
1
16" (406 mm)
HOT
COLD
6
6
5
4
2
1
3

- 3 - M965701 Rev. 1.1 (5/17)
3
4INSTALL HANDLES
• Turn VALVE STEMS (15) to off position.
• Align LEVER HANDLES (16) as shown and install onto ADAPTERS (10).Tighten SET SCREW (17) with
HEX WRENCH (14) supplied. Install PLUG BUTTONS (18).
INSTALL WALL SPOUT
• Twist and pull off PLASTER GUARDS (1). Thread counter clock-wise ROUGH-IN NIPPLE (2) with a at blade screwdriver
and remove.
• Inspect that SPOUT NIPPLE O-RINGS (3 & 4) are seated in the grooves of SPOUT NIPPLE (5). See View “A”.
• Thread SPOUT NIPPLE (5) into VALVE BODY (6) and tighten until O-RING (3) is fully seated against VALVE BODY (6).
• Mount WALL ESCUTCHEON (9). Thread ADAPTERS (10) onto VALVE (11) until WALL ESCUTCHEON (9) is ush
against nished wall.
• Inspect that ADAPTER O-RINGS (3, 4) are seated in the grooves of ADAPTER (5). See View “A”. Install ADAPTER (5)
into spout outlet and tighten with wrench. Thread SPOUT ADAPTER (7) onto ADAPTER (5) so that the groove
extends 9/16" beyond face of ESCUTCHEON. See View “B”.
• Push SPOUT (12) onto SPOUT ADAPTER (7) until ush against WALL ESCUTCHEON (9). If SPOUT is not against
WALL ESCUTCHEON (9) pull spout off and adjust SPOUT ADAPTER (10).
• Tighten SET SCREW (13) with HEX WRENCH (14) supplied.
13
17 14
4
4
5
3
2
1
1
View A View B
VIEW "A"
VIEW "B"
VALVE STEM
OFF
OFF
VALVE
STEM
5
6
7
11 9
11 10
12
10
16
16
8 SPOUT
O-RING
18
15
15
14
9/16"
(14mm)
GROOVE
FINISHED
WALL
GROOVE
ESCUTCHEON

- 4 - M965701 Rev. 1.1 (5/17)
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
BRUSHED NICKEL 144
MODEL NUMBERS
D3510045C
Rem®
Wall-Mounted Vessel
Lavatory Faucet Trim
5
• With HANDLE (1) in OFF position, turn on WATER SUPPLIES and check all connections for leaks.
• Remove AERATOR (2). First loosen aerator set screw with HEX WRENCH (3) supplied. Pull out AERATOR (2) with
AERATOR KEY (4).
• Operate HANDLES (1) to ush water lines thoroughly.
• Replace AERATOR (2) and tighten set screw.
TEST INSTALLED FAUCET
OFF
ON
OFF
ON
HEX WRENCH
(Supplied)
3
2
4
1
H960740.191
EXTENSION KIT
H960838.XXX
CONTROL HANDLE
H960854.191
ADAPTER RECEIVER (1.2 GPM)
H960853.191
ADAPTER
H960836.191
EXTENSION
M964513-0070A
SPOUT SET SCREW
A962294.191
AERATOR ASSEMBLY
H960856.XXX
ROSETTE