Dynojet POWER VISION 3 User manual

X
POWERVISION3
Installation Guide for: PV3-15-02
Model Coverage:
2011-2017Harley Davidson Softail Models
96" Twin Cam / 103" Twin Cam
2012-2017 Harley Davidson Dyna Models
96" Twin Cam / 103" Twin Cam
2014-2016 Harley Davidson Touring Models
96" Twin Cam / 103" Twin Cam/ 110" Twin Cam
2018-2021 Harley Davidson Softail Models
107" Milwaukee MS / 114" Milwaukee MS
2017-2020 Harley Davidson Touring Models
107" MS / 114" MS/ 117"MS
2014-2021 Harley Davidson Sportster 883 Models
2014-2021 Harley Davidson Sportster 1200 Models
2015-2019 Harley Davidson Street 500
2015-2021 Harley Davidson Street 750
PARTSLIST
1 POWERVISION
1 REFLASHHARNESS
1 USB CABLE
2 VELCRO
2 DYNOJETDECAL
I
PLEASEREADALLDIRECTIONSBEFORESTARTINGINSTALLATIONj
X 98200108.02

INTRODUCTION
RETURN
SCROLL
ENTER
HOME/LOG
SCROLL
ff
I
(>
rr
I
II
\\
I
A !~
-□
IF
V 110J
::; DYNO.'JET 1
EngineSpeed S11eed
3450 52
Gear TP
3 42.1
POWERVISIONOVERVIEW-FRONTVIEW
USB CABLE PORT
CONNECT TO COMPUTER DIAGNOSTIC CABLE PORT
CONNECT TO VEHICLE
POWERVISIONOVERVIEW-SIDEVIEW
I Thank you for purchasing the Power Vision from Dynojet
Research. At Dynojet, our mission is to make every ride
the ultimate ride. The Power Vision allows you to tune
your stock ECUto achieve optimal performance from
your vehicle.
The Power Vision is the device to interface between
your computer and the vehicle ECU. Use the buttons
to navigate the device menus, make selections, cycle
through the four full-color available gauge screens, and
log data. Connect to the diagnostic port to flash a tune;
use the USB connection to interface between the Power
Vision and your computer.
Make your Power Vision device yours; display the
channels you want to see with four user-customizable
full-color gauge screens. Make the Power Vision your
window into your vehicle; secure the Power Vision to
your dashboard or handlebars to monitor any desired
set of gauges such as Throttle Position, Engine Speed,
and more. Wideband Air:Fuel Ratio and integrated belt
temperature can be added as channels to the PV3's
monitors by adding the accessories available at
www.dynojet.com.
For state of the art technical support, please visit
www.dynojet.zendesk.com.
INSTALLINGTHEPOWERVISION
DIAGNOSTICPORT
2 HARLEY-DAVIDSONINSTALLATIONGUIDE
This installation was done on a Harley-Davidson Night
Rod. Your bike and set-up may vary.
1 Attach the diagnostic cable to the diagnostic port on the
Power Vision and to the diagnostic port on the vehicle.
Refer to the Diagnostic Port Location on page 3.
Note: The Power Vision may be damaged if installed
improperly. The location of the diagnostic port varies
depending on the model, please refer to a service
manual or contact Dynojet for the exact location.
Use caution as many models use the same style
connector for accessories; your Power Vision MUSTbe
connected to the diagnostic port.
98200108

INSTALLINGTHEPOWERVISIONCONTINUED
ROUTINGTHECABLE
2 Route the Power Vision cable away from any moving or
hot parts. Dynojet recommends using zip ties to secure
the cable to existing non-moving components.
3 Secure the Power Vision to the vehicle using the supplied
Velcro or mounting hardware. Make sure the Power Vision
will not interfere with the operation of the vehicle.
Visit www.dynojet.com for an array of mounting solutions
for your Power Vision.
Note: The Power Vision does not need to be mounted
to the vehicle, however, the Power Vision provides
a window into your vehicle. Mount the Power Vision
to your handlebars and gain access to customizable
full-color gauge screens, along with data logging and
troubleshooting screens.
DIAGNOSTICPORTLOCATION
2012-2017 Dyna Models 2014-2020 Touring Models 2015-2021 Street Models
Diagnostic connector is located behind the Left hand
side cover. Connector is Light Grey in color with black
rubber plug installed.
Diagnostic connector is located behind the left hand
side cover. Connector is Light Grey in color with a black
rubber plug installed.
Diagnostic connector is located behind right hand
side cover. Connector is Light Greyin color with black
rubber plug installed.
2014-2021 Sportster Models
(including XR Models)
Diagnostic connector is located behind the Left hand
side cover. Connector is Light Grey in color with black
rubber plug installed.
2011-2011softail Models
Diagnostic connector is located under the seat,
attached to the frame bythe rear fender. Connector is
Light Grey in color, with black rubber plug installed.
3

GETTINGSTARTED
Use the Tune File Wizard to prepare your Power Vision
device with the stock (stk) and tune (djt) files needed to
flash your vehicle.
1 Connect the Power Vision to the vehicle.
2 Turn the key on. The Power Vision will scan for files.
There are three possible file states:
File State 1: No compatible tune or stock files.
File State 2: No compatible tune files.
File State 3: All required files found.
File State 1:
Press the Enter
button for ECU read
to begin the tuning
process. This process
takes about fifteen
minutes.
File State 2:
GETTINGSTARTED
NOCOMPATIBLESTOCKFILES
AnECUreadiirequire:ttobegmthe
tuningµroces.s..
PRESSC TOREADECU
PRESSt>TOEXITwtlA!lll
3 Gauges are displayed. Go to tunes.dynojet.com/ to
download tune files.
CONNECTECU File State 3:
Connect the Power Vision to the
vehicle diagnostic port to collect
ECUinformation. Turn the key on. Pleaseconnecttothevehicle
diagnosticporttocontinue.
PRESSt>TORETURN
All required files found. The Power
Vision is ready to flash a tune to the
connected vehicle.
FLASHINGYOURVEHICLE
The Power Vision must be paired to the connected vehicle ECU
to function properly.
Note: Once paired to the vehicle ECU,the Power Vision will
not work on another vehicle without purchasing a tune
license.
1 From the Main Menu, select Flash Tune.
2 Select the tune file (.djt) and press Enter to view the Tune Info.
Note: The Dynojet tune file (.djt) is a tune file which is
different (better than stock performance or the necessary
file when bolting on an exhaust, for example); the stock file
(.stk) is the direct duplicate of what the OEM shipped.
3 Press Enter to accept the tune and pair the Power Vision to the
vehicle.
Note: Pair to vehicle will only happen on the first flash.
4 Press Enter to pair and lock the Power Vision to the ECUand to
begin the flash. Do not turn off the key switch or disconnect the
Power Vision during the flash.
5 After the flash is complete, turn the key off and wait 45 seconds
before turning the key back on to start.
4 HARLEY-DAVIDSONINSTALLATIONGUIDE
VEHICLETOOLS
DEVICETOOLS
NOTPAIRED
PAIRTHISDEVICETOTHE
CONNECTEDVEHICLE?
PRESSOTOCOlfflNUE
PflESS'!>IORETURN
CI502TA301.djt
FLASHTUNE
I FLASHECUWITHSELECTED
TUNEFILE?
PRESSOTOCONTINU[
PR!SSt, TORETURN
READECU
ANECUREADCANTAKEUPTO
15MINUTESTOCOMPLETE
GETTINGSTARTED
NOCOMPATIBLETUNEFILES
Talkl11dJ~ILJ!e>,IM:
TUNES.OYNOJET.COM/
PRESSOTO SEARCHAGAIN
READYTOFLASH
All REQUIREDFILESFOUND
PRESSCTOREAOECU
PRESSt>TOEXJTWIZARO
TUNEINFO
FILE:C1~01TA101.dJt
TUNER
COMPATS
DESCRIPTION,20!7fouting
t!ll1Bf824
Stackhh;tUSI
S1c:klntake
PRESSC TOSTARTECUf!ASH
98200108

VIEWINGTHEVEHICLEINFORMATION
This menu allows you to view the device status (paired/not
paired), VIN#, Model ID, ECUserial number, tune compat, and
checksum compat.
Select Vehicle Tools>Vehicle Information.
MAINMENU
FLASHTUNE
II
DEVICETOOLS READECU
VIEWINGTHEDIAGNOSTICCODES
This menu allows you to read and clear diagnostic trouble
codes.
1To read codes, select Vehicle Tools>Diagnostics>Active
Codes.
2 Toclear codes, select Vehicle Tools>Diagnostics>Clear
Codes.
READINGTHEECU
This menu allows you to read the ECU.This process takes
about fifteen minutes.
Select Vehicle Tools>Read ECU.
~RESTORINGTHEECU
This menu allows you to restore the ECU. Use Restore ECUif
the device does not complete the flash or if your vehicle will
not start.
Select Vehicle Tools>Restore ECU.
CONFIGURINGGAUGES
Make your Power Vision device yours; display the channels
you want to see with four user-customizable full-color gauge
screens. Each gauge screen has four configurable channels.
Monitor channels such as Wideband, AFR, Boost, and integrated
belt temperature sensor. Sample gauges shown here; for
a complete list of monitors available, open the tune file in
Power Core or scroll through the gauges on the device when
configuring or selecting channels for the list of options.
1 From the Main Menu, select Device Tools>Configure Gauges.
2 Select a gauge screen and press Enter.
3 Select a channel and press Enter.
4 Select a channel from the list and press Enter.
5 Select the precision or units for that channel and press Enter.
6 Continue setting up the remaining channels as desired.
7 Continue configuring the remaining gauge screens as desired.
MAINMENU
MAINMENU
FLASHTUNE
II
DEVICETOOLS
MAINMENU
FLASHTUNE
II
DEVICETOOLS
MAINMENU
FLASHTUNE
VEHICLETOOLS
II
CHANNEL3
CHANNEL4
::; DYNO.,""E,
EngineSpeed Speed
3450 52
Gear TP
3 42.1
:€
VEHICLETOOLS
VEHICLETOOLS
VEHICLEINFORMATION
I VEHICLETOOLS
l READECU
DELETEDATALOG
I-•1"1!:l
DEVICETOOLS
. •' .
DEVICEINFORMATION
REFORMATDISK
RPMxlOO
RPMxlOOO
::; DYND3Ei'
!AT AAT
84 71
B+ Baro
13.8 13.9
C
i
VEHICLEINFO
PAIREDl'EHICL[DEVICENOTPAIR£D
VIN:56KMSA005f3101859
MOOH
ID:NFSBBAZOOO
TUNECOMPAT:
VMB860l5.J[I
CSUM
CQMPAl50SA7B03
CLEARCODES
READECU
ANECUREADCANTAKEUPTO
15MINUTESTOCOMPLETE
PRESS □ TOCONTINUE
PRESS'!>HlRrnJRN
RESTOREECU
RESTOREECUTOORIGINALSTK
FILE?
~~~r~/i~:~E
0.00
0.000
::; DYNllaiEi'
FrontCl! RearCl!
198.2 191.7
TotalFTF RearFTF
100 115
f
5

LOGGINGDATA
ThePowerVision isapowerful loggingtool to diagnoserunning issues.
Usethe PowerVisionto logall vehicle operatingdata and reviewthe
data inthe PowerCoresoftware. Troubleshootanissuesuch as knock,
speed/RPMlimitation, throttle bladeclosureand more by keepingthe
. .
PowerV1s1onmountedto viewand record channels.
1 Press the Log©button to begin logging. The Power Vision
screen will illuminate a bright red banner across the top when
logging.
2 Press the Log©button again to stop logging.
3 Use the Power Core software to view log files.
Snapshot Log: Press and hold the Log©button for two
seconds to record the previous two minutes of operating time.
DELETINGDATALOGS
This menu allows you to delete data logs.
1 Select Vehicle Tools>Delete Data Log.
2 Select a specific log to delete or select *Delete All Logs*.
DATALDG
DATALOGGINGHASSTARTED.II
PRESSAGAINTOSTOP
DATALOG
Cl502TAIOl_LOG_1.wp8
SAVEDSUCCESSFULLY
MAINMENU
FLASHTUNE
II
DEVICETOOLS
I
.L
I
~=T'f~.~·:1:1>'.~
EngineSpeed Speed
3450 52 I
Gear TP
3 42.1
VEHICLETOOLS
DIAGNOSTICS
READECU I
-1,:11 ■ .111:.1'<11,111111,:-
VIEWINGTHEDEVICEINFORMATION
This menu allows you to view the device firmware version,
serial number, and stock code.
Select Device Tools>Device Information.
MAINMENU
FLASHTUNE
VEHICLETOOLS
-1,.11.•1••--•III
REFORMATTINGTHEDISK
This menu allows you to reformat the disk and erase all data.
Select Device Tools>Reformat Disk. MAINMENU
FLASHTUNE
VEHICLETOOLS
DEVICETOOLS
CHANGINGTHESETTINGS
This menu allows you to rotate the screen allowing you to
change the orientation of the Power Vision device along with
adjusting the screen brightness. Turn the brightness up and
make your screen pop!
Select Device Tools>Settings>Rotate Screen to flip the
screen.
Select Device Tools>Settings>Brightness to change the
screen brightness.
6 HARLEY-DAVIDSONINSTALLATIONGUIDE
DEVICETOOLS
DEVICEINFORMATION
REFORMATDISK
DEVICETOOLS
DEVICEINFORMATION
REFORMATDISK
-uu
I
1
I
DEVICETOOLS
CONFIGUREGAUGES
I 1,'121 •1,,. ,11 I
REFORMATDISK
DEVICETOOLS
CONFIGUREGAUGES
DEVICEINFORMATION
REFORMATDISK
DEVICESETTINGS
'I. ....
BRIGHTNESS
DEVICESETTINGS
ROTATESCREEN
:1:1,
I
.L
I
....
I
.L
I
SAVINGLOG
SAVINGLOG...
LOGFILES
*DeleteAlllogs*
C1502TAI01_LOG_1.wp8
I • I ,. ,:
I C1502TAIOI_LOG_3.wp8
DEVICEINFORMATION
DYNOJETPOWERVISION
FWVERSION:3.1.7-443.27973
SERIALNUMBER:PV00032968
STOCKCODE:16125083
REFORMATDISK
All DATAWIUBEERASED
PRUSCTOCONTINUE
PRESS'!)TORETURti
ROTATESCREEN
THISWill FLIPTHESCREEN
PR£SSOTDCONTINUE
PRESS'!)TO RETURN
BRIGHTNESS
20%
PRESSOIOCONTINUE
PRES5'!)TORffilRN
98200108

UPDATINGTHEDEVICE
This menu allows you to update the device with the latest firmware. MAINMENU
1 Goto www.dynojet.com. FLASHTUNE
2 From the top navigation menu, select Support>Downloads. VEHICLETOOLS
3 Click PowerVision3.
4 Click the Firmware drop-down and download the Power Vision 3
Firmware for Polaris.
5 Save the file to your device.
6 Select Device Tools>Update Device.
EXPORTDIAGNOSTICS
This menu allows you to create a BIN file containing device
information used by Dynojet Tech Support.
1 Select Device Tools>Export Diagnostics.
2 If requested by Dynojet Tech Support, connect your Power
Vision to a computer and email the BIN file to
[email protected].
.DEVICETOOLS
MAINMENU
FLASHTUNE
VEHICLETOOLS
DEVICETOOLS,
DEVICETOOLS
REFORMATDISK
SETTINGS
'I• I
DEVICETOOLS
UPDATEDEVICE
GENERATEUNLOCKFILE
EXPORTDIAGNOSTICS
FILEGENERATED
DIAGNOSTICSFILEGENERATED
PRESS □ TOCOIITINUE
PRESS TOREIURN
USINGTHEPOWERVISIONUPDATECLIENT
This stand alone application will launch the Update Client
allowing you to update your Power Vision with the latest
firmware, retrieve additional tunes, or restore the Power Vision to
the original Dynojet factory settings.
1 Connect the Power Vision to your computer using the included
USBcable.
2 Navigate to the POWERVISIONdrive attached to your computer
and run the Update.exe file.
3 Click Update to load the current firmware. If the Update button is
grayed out, your Power Vision already has the latest firmware.
4 Click Restore to reload all original Dynojet tune and stock files.
5 Click Get Tunes to open the Dynojet Tune Finder. Follow the
instructions to Upload your PV_Info.txt file and retrieve new tunes.
6 Click Manual Firmware Update to navigate to and load a version
of firmware already saved on your computer.
Help
l1Yi\fll:iE7:
I UpdateI
I Restore11 GetTunesI
I ManualFirmwareUpdateI
finnwareVersion:2.11.7703.23803SIN:PW002975i
- X
1.QJ.O
INSTALLINGTHEPOWERCORESOFTWARE
Download the Power Core software and take tuning to a whole
new level.
Note: Downloading the Power Core software is optional
and not necessary to use the Power Vision.
1 Goto www.dynojet.com.
2 Fromthe top navigation menu, select Support>Downloads.
3 click Power Vision 3.
4 click the Software drop-down and download the Dynojet Power
Core software.
5 Double-click the saved file to begin installation. Follow the on-screen
prompts. Refer to the Power Core Help for more information.
IJYi\fll:iET 7

2191MENDENHALLDRIVE,NORTHLASVEGAS,NV89081- 800-992-4993- DYNOJET.COM
© 2019-2022DYNOJETRESEARCHALLRIGHTSRESERVED