Dynojet Power commander V User manual

19-005 www.powercommander.com 2009-2011 Polaris Sportsman 850 - PCV - 1
PARTS LIST
1 Power Commander
1 USB Cable
1 Installation Guide
2 Power Commander Decals
2 Dynojet Decals
2 Velcro strips
1 Alcohol swab
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2009-2011 Polaris Sportsman 850
Installation Instructions
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
2191 Mendenhall Drive North Las Vegas, NV 89081 [phone] www.powercommander.com

19-005 www.powercommander.com 2009-2011 Polaris Sportsman 850 - PCV - 2
EXPANSION PORTS 1 & 2
Optional Accessories such as
POD-300 unit or Auto-tune kit.
POWER COMMANDER V
INPUT ACCESSORY GUIDE
Map - (Input 1 or 2) The PCV has the ability to hold
2 different base maps. You can switch on the
fly between these two base maps when you
hook up a switch to the MAP inputs. You can
use any open/close type switch. The polarity
of the wires is not important. When using the
Autotune kit one position will hold a base map
and the other position will let you activate the
learning mode. When the switch is “CLOSED”
Autotune will be activated. (Set to Switch
Input #1 by default.)
Shifter- (Input 1 or 2) These inputs are for use with the
Dynojet quickshifter. Insert the wires from the
Dynojet quickshifter into the SHIFTER inputs.
The polarity of the wires is not important. (Set
to Switch Input #2 by default.)
Speed- If your application has a speed sensor then
you can tap into the signal side of the sensor
and run a wire into this input. This will allow
you to calculate gear position in the Control
Center Software. Once gear position is setup
you can alter your map based on gear position
and setup gear dependent kill times when
using a quickshifter.
Analog- This input is for a 0-5v signal such as
engine temp, boost, etc. Once this input
is established you can alter your fuel curve
based on this input in the control center
software.
Crank- Do NOT connect anything to this port unless
instructed to do so by Dynojet. It is used to
transfer crank trigger data from one module to
another.
ACCESSORY INPUTS
Wire connections:
To input wires into the PCV first remove the rubber
plug on the backside of the unit and loosen the
screw for the corresponding input. Using a 22-24
gauge wire strip about 10mm from its end. Push the
wire into the hole of the PCV until is stops and then
tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make
inserting them easier.
CRANK
ANALOG
SPEED
INPUT 1 (Grnd)
INPUT 1
INPUT 2 (Grnd)
INPUT 2
USB CONNECTION

19-005 www.powercommander.com 2009-2011 Polaris Sportsman 850 - PCV - 3
1 Remove the seat and left side panel.
2 Install the PCV on top of the stock ECU using the supplied velcro (Fig. A).
Make sure to clean both surfaces before attaching with the alcohol swab.
3 Unplug the stock wiring harness from the Throttle Position Sensor (Fig. B).
The TPS is located on the front side of the throttle bodies.
4 Plug the 3-pin connectors of the PCV in-line of the stock TPS and wiring
harness (Fig. C).
FIG.A
FIG.C
FIG.B
Unplug

19-005 www.powercommander.com 2009-2011 Polaris Sportsman 850 - PCV - 4
5 Unplug the stock wiring harness from each injector (Fig. D).
FIG.D
6 Plug the PCV in-line of the stock wiring harness and injectors (Fig. E).
Connect the ORANGE colored wires of the PCV to the front cylinder.
FIG.E
FOLLOW THESE STEPS FOR THE 2009-2010 MODELS. FOR THE 2011
MODEL GO TO STEP 9
7 Route the ground wire of the PCV along the left hand frame rail and go to the
battery at the rear of the ATV (Fig. F).
FIG.F
Ground wire
Unplug
Unplug

19-005 www.powercommander.com 2009-2011 Polaris Sportsman 850 - PCV - 5
8 Attach the ground wire of the PCV to the ground bolt near the battery (Fig. G).
FIG.G
FOLLOW THESE STEPS FOR THE 2011 MODEL
9 Remove the battery access cover on the front of the ATV.
10 Attach the ground wire of the PCV to the ground bolt near the brake reservoir
(Fig. H).
11 Reinstall the seat and side cover.
FIG.H
Ground
Ground