Eagle Group A222014 User manual

(underside
view of seat)
Lay on
top of
split
sleeves.
ASSEMBLY INSTRUCTIONS
Gowning Benches with Undershelf
—36˝, 48˝, and 60˝ in length
If your gowning rack is 72˝-long, refer to reverse page.
PART #A222014
EG10073 Revised 10/07
Eagle Foodservice Equipment, Eagle MHC, SpecFAB, and Retail Display are divisions of Eagle Group. ©2007 by the Eagle Group
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • www.eaglegrp.com
• Phone: [phone] • (Foodservice) 800/441-8440 • (MHC/Retail) 800/637-5100
• Fax: [phone]
CAUTION
INSPECT CONTENTS IMMEDIATELY AND FILE CLAIM WITH DELIVERING CARRIER FOR ANY DAMAGE.
SAVE YOUR BOX AND ALL PACKING MATERIALS.
YOU ARE RESPONSIBLE FOR DAMAGE TO YOUR UNIT IF RETURNED IMPROPERLY PACKED.
(End)
Step 2 - Mount undershelf.
split
sleeves
undershelf
seat
split
sleeve
post
Step 1 - Attach split sleeves (for undershelf)
to lowest groove on posts.
• The wider part of the taper goes toward the bottom.
• Make sure rib on split sleeve is seated into a groove
on the post.
split
sleeve
corner
collar
post
Step 3: Secure undershelf.
Note: Do NOT hammer directly
on wire or corner.
Step 4: Attach seat to posts.
Please note: If additional undershelf was ordered, install now by repeating Steps 1 through 3,
attaching split sleeves onto middle of posts. Otherwise, proceed to Step 4 below.
Tap with
rubber
mallet.
Place board
across shelf
corners.
split
sleeves
Step 5: Secure
feet to the floor.
Hardware not
included.
Assembly is complete.

ASSEMBLY INSTRUCTIONS
Gowning Benches with Undershelf
—72˝ in length
Eagle Foodservice Equipment, Eagle MHC, SpecFAB, and Retail Display are divisions of Eagle Group. ©2007 by the Eagle Group
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • www.eaglegrp.com
• Phone: [phone] • (Foodservice) 800/441-8440 • (MHC/Retail) 800/637-5100
• Fax: [phone]
(End)
Please note:
72˝-long gowning racks come with SIX posts and TWO wire undershelves.
The enclosed S-hooks will therefore be required to complete assembly.
undershelf
post
split
sleeve
corner
collar
post
undershelf
post
Step 2 - Mount
first undershelf.
split
sleeves
Step 3 - By repeating Steps 1 and 2,
attach second undershelf to the two
remaining posts.
Step 4 - Connect second
assembly to first assembly.
NOTE: Place each “S” hook near a
post as closely as possible.
second
assembly
“S” hook
first
assembly
“S”
hook
Step 5: Secure undershelves.
Note: Do NOT hammer directly on
wire or corner.
Tap with
rubber
mallet.
Place board
across shelf
corners.
Step 1 - Attach split sleeves (for first
undershelf) to lowest groove on four posts.
• The wider part of the taper goes toward the bottom.
• Make sure rib on split sleeve is seated into a groove
on the post.
Step 6: Attach seat to posts.
Refer to Step 4 on reverse page.
Assembly is complete.
Please note:
If additional
undershelves were
ordered, install now
by repeating
Steps 1 through 5,
attaching split
sleeves onto middle
of posts. Otherwise,
proceed to Step 6.
Step 7: Secure
feet to the floor.
Hardware not
included.