Eagle Group Spec-Master 502971 User manual

ASSEMBLY INSTRUCTIONS
Spec-Master®Drawers for
Tables with Channel Frame
(Drawers #502971 and 502972)
(For Tables with Angle Frame, see Page 3)
PART #333309
EG9825 Revised 10/05
Eagle Foodservice Equipment, Eagle MHC, SpecFAB, and Retail Display are divisions of Eagle Group. ©2005 by the Eagle Group
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • www.eaglegrp.com
• Phone: [phone] • (Foodservice) 800/441-8440 • (MHC/Retail) 800/637-5100
• Fax: [phone] or 302/653-3036
CAUTION
INSPECT CONTENTS IMMEDIATELY AND FILE CLAIM WITH DELIVERING CARRIER FOR ANY DAMAGE.
SAVE YOUR BOX AND ALL PACKING MATERIALS.
YOU ARE RESPONSIBLE FOR DAMAGE TO YOUR UNIT IF RETURNED IMPROPERLY PACKED.
Parts List
item qty part # description
#1 2 316985 Drawer Mounting Bracket for
24˝-wide tables
or
#1 2 316986 Drawer Mounting Bracket for
30˝- and 36˝-wide tables
or
#1 2 316987 Drawer Mounting Bracket for
30˝-wide tables
#2 4 308624 #10-24 x 1⁄2˝ Screw
#3 4301492 #10 Lock Washer
#4 4300755 #10-24 Hex Nut
#5 1 Drawer Enclosure (pan not shown)
#6 4 313630* #12 x 3⁄4˝ Sheet Metal Screw
* These screws are premounted to the table channel framing
(underneath tabletop), and will be used to mount drawer brackets.
Before assembly:
• Determine applicable sets of holes in brackets
and in drawer enclosure.
• Please note that 20˝ x 15˝ drawers require
holes to be drilled into table channel framing.
(actual size of hardware)
#1
#2
#3
#4
#1
#5
#6
This hole sets the
drawer in further
under the table.
(continued on Page 2)
#6#4
#3
#2

ASSEMBLY INSTRUCTIONS
Spec-Master®Drawers for
Tables with Channel Frame
(Drawers #502971 and 502972)
2
(continued from front page)
bracket
(right side)
front of table
drawer
enclosure
drawer
pan
drawer
enclosure
Step 2 - Remove drawer pan from
drawer enclosure.
drawer
pan
drawer
enclosure
Step 4 - Place drawer pan back into
drawer enclosure.
Item #3
#301492
lock washer
Item #4
#300755
hex nut
Item #2
#308624
screw
Step 3 - Attach drawer
enclosure to brackets.
Tighten down all hardware.
table channels
underneath tabletop
Item #1
drawer mounting brackets
Item #6
screw
Item #6
screw
Step 1 - Attach brackets to table channels.
Do NOT tighten down screws.
(End)

PLEASE NOTE:
To mount drawers onto
custom equipment with
angle frame construction,
kit #605499 is required.
ASSEMBLY INSTRUCTIONS
Spec-Master®Drawers for
Tables with Angle Frame
(Drawers #502971 and 502972)
3
Parts List
#qty part # description
#1 2 336255 Drawer Mounting Bracket
#2 8 308624 #10-24 x 1⁄2˝ Pan Head Screw
#3 8 301492 #10 Lock Washer
#4 8 300755 #10-24 Hex Nut
#5 1 Drawer Enclosure (pan not shown)
#1
drawer
mounting bracket
hole used to attach
bracket to angle
framing of table
top set of holes
for tables with
rolled edges
middle set of holes
for tables with
square edges
bottom set of holes
for tables with
box marine edges
#1
#2
#5 #3
#4
Before assembly:
• Determine applicable sets of holes
in brackets and in drawer enclosure.
front of table
Item #1
right-hand
bracket
Item #1
left-hand
bracket
angle framing
of table
underneath tabletop
Item #3
#301492
lock washer
Item #4
#300755
hex nut
Item #2
#308624
pan head
screw
CAUTION
INSPECT CONTENTS IMMEDIATELY AND FILE CLAIM WITH DELIVERING CARRIER FOR ANY DAMAGE.
SAVE YOUR BOX AND ALL PACKING MATERIALS.
YOU ARE RESPONSIBLE FOR DAMAGE TO YOUR UNIT IF RETURNED IMPROPERLY PACKED.
Step 1 - Attach brackets to angle framing of table.
(continued on back page)
#4
#3
#2
(actual size of hardware)

Eagle Foodservice Equipment, Eagle MHC, SpecFAB, and Retail Display are divisions of Eagle Group. ©2005 by the Eagle Group
• 100 Industrial Boulevard, Clayton, Delaware 19938-8903 U.S.A. • www.eaglegrp.com
• Phone: [phone] • (Foodservice) 800/441-8440 • (MHC/Retail) 800/637-5100
• Fax: [phone] or 302/653-3036
ASSEMBLY INSTRUCTIONS
Spec-Master®Drawers for
Tables with Angle Frame
(Drawers #502971 and 502972)
(continued from page 3)
drawer
pan
drawer
enclosure
Step 2 - Remove drawer pan from
drawer enclosure.
front of table
drawer
pan
drawer
enclosure
Step 4 - Place drawer pan back into drawer
enclosure.
Step 3 - Attach drawer enclosure to brackets.
drawer
enclosure
(End)
Item #3
#301492
lock washer
Item #4
#300755
hex nut
Item #2
#308624
screw
bracket
(right side)