EAST COAST Montreal Wardrobe User guide

Montreal
Wardrobe
Assembly and care
instructions

Small Bolt (24mm) x 4
IMPORTANT
RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
Handle x 4
Cam Pin x 4
Large Bolt (70mm) x 6Medium Bolt (27mm) x 28
Hexagon key
Dowel x 12Short Woodscrew x 60Long Woodscrew x 8 Medium Woodscrew x 12
Hinge x 6Cam Nut x 4
Hardware:
A
B
Before assembling the Wardrobe,
note that some of the joints use
Cam pins A, screwed into one part,
secured by Cam nuts B inserted
into the large hole in the mating
part.
The Cam nut is secured by aligning
the arrow on its surface with the
Cam pin, inserting into the hole,
and rotating approximately half
a turn with a large flat bladed
screwdriver.
Thank you for purchasing an East Coast product. It’s been carefully designed and constructed to oer
quality, safety and reliability for you and your baby.
If you have a query about this product or require replacement parts, please contact 01692 408802.
Your child’s safety is your responsibility. Keep children clear during assembly as the fittings pack contains
small parts which may present a choking hazard. Please read the instructions and warnings carefully
before use.
Lay out the parts on a soft level surface and compare to the parts checklist (Pages 2 & 3). Don’t throw
away any packaging until you’re sure that you have all the parts.
You will need the following tools to complete assembly:
Flat-headed screwdriver and cross-point screwdriver
2

Side panel x 2
Door x 2
Lower shelf
Upper shelf
Drawer Back
Drawer Front
Rear frame x 2
Left Drawer Side
Large back panel x 2
Small back panel x 2
Clothes rail
Lower frame
Top panel
Drawer Base
Rear crossbar
Front Crossbar x 2
Right Drawer Side
3
Wooden Parts:

Assembly 1:
NOTE: Take care to insert the dowels into the correct holes as indicated. Repeat for the opposite end
of each crossbar. (Total 12 dowels)
NOTE: Do not fully tighten the bolts at this stage.
You may find it easier to complete the following 4 stages of the assembly with the Side lying flat on
the floor or other soft level surface.
Top panel
Top panel
Rear crossbar
Front Crossbar x 2
Medium Bolt (27mm) x 2
Medium Bolt (27mm) x 2
Rear frame
Rear frame
Lower frame
4
Assembly 2:

NOTE: Repeat for second Side panel
Side panel
Side panel
Assembly 3:
Assembly 4:
Medium Bolt (27mm) x 4
Rear frame
Cam Pin x 4
Large Bolt (70mm) x 3
5

Assembly 6:
Assembly 5:
NOTES:
Ensure that the Front crossbars have the large holes in its ends facing downward.
Attach the Crossbars by inserting Cam Nuts, making sure that the arrow on one of the screwdriver
slots points to the nearest edge of the part. To secure the parts, turn the Cam Nut approximately 1/2
turn clockwise until resistance is felt.
Medium Bolt (27mm) x 6
Medium Bolt (27mm) x 2
Medium Bolt (27mm) x 2
Rear crossbar
Front Crossbar
Upper shelf
Lower shelf
Front Crossbar
Cam Nut x 2
6

NOTE: Fit the bolts as shown then stand the wardrobe up on a level surface for the remaining
assembly steps
Assembly 7:
Assembly 8:
NOTE:
Ensure all dowels are located in the correct holes in the second Side panel
Side panel
Cam Nut x 2
Medium Bolt (27mm) x 3
Medium Bolt (27mm) x 5
Large Bolt (70mm) x 3
7

NOTES:
Fit the two Medium bolts before attaching the Back panels.
Fit the top Small back panel first, making sure that the slot is at the top edge.
Stand the wardrobe in its final position and ensure that all bolts are fully tightened.
Fit the clothes rail to the inside of the wardrobe.
Slot at top edge
Assembly 9:
Large back panel
Large back panel
Small back panel
Small back panel
Medium Bolt (27mm) x 2
Short Woodscrew x 14
Short Woodscrew x 16
Short Woodscrew x 14
Short Woodscrew x 16
8

NOTE:
Repeat for second door
Long Woodscrew x 4
Long Woodscrew x 4
Right Drawer Side
Left Drawer Side
Drawer Base
Drawer Front
Drawer Back
Assembly 10:
Assembly 11:
Small Bolt (24mm) x 3
Door
Handle
Handle x 2
Medium Woodscrew x 6
Hinge x 3
9

Screw A
Door
Side panel
Screw B
With the wardrobe in its final position, the doors can be fitted.
Locate screw A on the hinge in the slot on the hinge plate attached to the Side panel.
The doors can be adjusted to fit by adjusting screws A and B in the rear part of each hinge to alter
the angle and fit of each door in its frame.
Fit the drawer to the wardrobe by lifting its front edge slightly and placing the plastic wheels at
the rear of the drawer into the metal channels on the wardrobe Side panels. Lower the front of the
drawer and push the drawer into the recess.
Assembly 12:
10

Assembly 13:
The Wardrobe is supplied with a fixing kit which will secure it and help to guard against accidental
tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
1. Place Wardrobe against the wall where it is to be fitted. Mark the wall 25mm (1”) down from the
top of the wardrobe.
2. Using the 25mm screw, washer and the appropriate wall fixing attach the fabric strap to the
marked position.
3. Open the door and thread the free end of the strap through the slot in the back panel.
4. From the inside of the Wardrobe, attach the fabric strap to the underside of the Top panel using
the 15mm screw and the washer.
Before use, ensure that the strap is securely fixed to both the wall and the Wardrobe.
1 2 3 4
The type of wall fixing you will require depends on the construction of the wall. See below for
details. If in doubt, seek professional advice.
Wood: If fixing to wood
make sure that it isn’t
chipboard as screws can
easily pull away the core
structure.
Brick or masonry: Use
the wall plug, provided
you are sure that your
wall is sound.
Cavity wall: Special
toggle wall plugs needed.
Seek expert advice.
Washer x 2
Fabric strap
Plastic wall plug
(For brick or masonry wall use only)
Screw (25mm)Screw (15mm)
11

For customer care or enquiries:
Call: 01692 408802
Email: [e-mail]
East Coast Nursery Ltd. Robertson House, North Walsham,
Norfolk, NR28 0BX
eastcoastnursery.co.uk 5002_V2
Care and maintenance
In use
All assembly fittings should be tightened properly and should be checked regularly and re-tightened
as necessary. Take care when moving the furniture, as careless handling may cause damage.
Cleaning is simple; just wipe over with a damp cloth, and avoid using strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the finish.
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires,
gas fires, etc. in the near vicinity of the wardrobe.
Do not use if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the distributor.
Only use the wardrobe on a stable and level surface.
Ensure that the wall strap is used to securely attach the wardrobe to the wall to prevent tipping.