Eaton P1/I2 Series Manual

Electric current! Danger to life!
Only skilledor instructedpersons may
carry out the following operations.
Lebensgefahr durch elektrischenStrom!
Nur Elektrofachkräfte undelektrotechnisch
unterwiesene Personen dürfen die im Folgenden
beschriebenen Arbeiten ausführen.
Tension électrique dangereuse !
Seules les personnes qualifiées et averties doivent
exécuter les travaux ci-après.
¡Corrienteeléctrica! ¡Peligro de muerte!
El trabajo a continuación descrito debe ser realizado
por personas cualificadas y advertidas.
Tensione elettrica: Pericolo di morte!
Solo persone abilitate e qualificate possono eseguire
le operazioni di seguito riportate.
触触电电危危险险！！
只允许专业人员和受过专业训练的人员进行
下列工作。
Электрический ток!Опасно для жизни!
Только специалисты или проинструктированные
лица могут выполнять следующие операции.
en
de
fr
es
it
zh
ru
Emergency On Call Service:Local representative (www.eaton.eu/aftersales)or [phone] (de,en) 1/2
Instruction Leaflet
Montageanweisung
Notice d’installation
Instrucciones de montaje
Istruzioni per il montaggio
安
安装装说说明明
Инструкция по монтажу
07/16 IL03802001Z
(AWA1150-1689)
P1…/I2…
P1…/I2(H)(-RT) P1…/I2(H)/SVB(-SW)
P1…/I2(H)(-RT)
P1…/I2(H)/SVB(-SW)
ON
OFF
d
b
≦3 x
d = 4 - 8 mm
b + d ≦47 mm
(d = 0.16 - 0.31“)
(b + d ≦1.85“)
P1… P1…/N P1…/HI11
UL-File: E 36 332
Suitable For UseAs Motor Branch Circuit
Disconnecting MeansWith Suffix SVB.
Break All Lines.
HI11-P1/P3 tightening
torque
0.5 - 1.5 mm21 Nm
(8.85 lb-in)
0.75 - 2.5 mm2
AWG 18 -AWG 14
P1… tightening
torque
1 x 1.0 -4.0 mm2
2 x 1.0 -4.0 mm21.6Nm (14.16 lb-in)
1 x 1.5 -6.0 mm2
2 x 1.5 -6.0 mm2
AWG14 - AWG 8
75 °C Cu wire only
1
L1 L2 L3
T1T2T3
2
3
4
5
6
0
I
N
N
1
L1 L2 L3
T1 T2 T3
2
3
4
5
6
0
I
14
13 21
22
1
L1 L2 L3
T1 T2 T3
2
3
4
5
6
0
I
ON
OFF
ON
OFF
2 x ST 3.9 x 19
1 Nm (8.85 lb-in)
1.2 Nm
(10.62 lb-in)
0.6 Nm
(5.31 lb-in)
0.6 Nm
(5.31 lb-in)
ZFS...T0
ON
OFF
171 mm (6.73”)
100 mm (3.94”)
M4
80 mm (3.15”)

2/2 Emergency On Call Service: Local representative (www.eaton.eu/aftersales)or [phone] (de, en)
07/16 IL03802001Z
Eaton Industries GmbH, Hein-Moeller-Straße 7-11, 53115 Bonn, Germany
©1999 by EatonIndustries GmbH,www.eaton.eu/documentation All Rights Reserved
07/16 IL03802001Zasim
Printed in Great Britain (08/16)
P1…/I2…
V-M25 KT-M25
P1.../I2 (H)(-NA): ⌀ ≦ 11 mm (⌀ ≦ 0.43”)
K-CI-K1/2
N-P1Z HI11-P1/P3Z
P1...
P1.../I2(H)(-NA)
⌀ ≦ 8 mm
(⌀ ≦ 0.31”)
P1.../I2...: V-M25
P1.../I2(H)(-NA): ⌀ ≦ 16 mm (⌀ ≦ 0.63”)
P1.../I2...: V-M25
P1.../I2(H)(-NA): ⌀ ≦ 16 mm (⌀ ≦ 0.63”)
1P1…/I2(H)(-NA)
2
3 4
￫If you are using N-P1Z or HI11-P1/P3,
you will have to remove terminalK-CI-K1/2. ￫Con l’utilizzo di N-P1Z o HI11-P1/P3 il
morsetto K-CI-K1/2 deve essererimosso.
￫Bei Verwendung von N-P1Z oder HI11-P1/P3
muss die Klemme K-CI-K1/2 entfernt werden. ￫使用 N-P1Z 或HI11-P1/P3 时，
必须移除端子 K-CI-K1/2。
￫L’utilisation de N-P1Z ou HI11-P1/P3
requiert le démontage de la borne K-CI-K1/2. ￫Прииспользовании N-P1Z или HI11-P1/P3
необходимо убратьклемму K-CI-K1/2.
￫Al utilizar N-P1Z oHI11-P1/P3 debe
eliminarseel borne K-CI-K1/2.
1 2
3