Eaton Powerware PowerPass 9125 User manual

Powerware 9125 Two-in-One
PowerPass Distribution Module
User’s Guide
®
®
For use with Powerware 9125 Two-in-One
5000/6000 VA UPS Models
All manuals and user guides at all-guides.com
all-guides.com

Class A EMC Statements
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
ICES-003
This Class A Interference Causing Equipment meets all requirements of the Canadian Interference Causing
Equipment Regulations ICES-003.
Cet appareil numérique de la classe A respecte toutes les exigences du Reglement sur le matériel brouilleur du
Canada.
EN 50091-2
Some configurations are classified under EN 50091-2 as “Class-A UPS for Unrestricted Sales Distribution.” For
these configurations, the following applies:
WARNING This is a Class A-UPS Product. In a domestic environment, this product may cause radio interference, in
which case, the user may be required to take additional measures.
Powerware and PowerPass are registered trademarks of Eaton Electrical Inc.
Greenlee is a registered trademark of Greenlee Textron.
ECopyright 2003–2006 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
All manuals and user guides at all-guides.com

Requesting a Declaration of Conformity
Units that are labeled with a CE mark comply with the following harmonized standards and EU directives:
SHarmonized Standards: EN 50091-1-1 and EN 50091-2; IEC 60950 Third Edition
SEU Directives: 73/23/EEC, Council Directive on equipment designed for use within certain voltage limits
93/68/EEC, Amending Directive 73/23/EEC
89/336/EEC, Council Directive relating to electromagnetic compatibility
92/31/EEC, Amending Directive 89/336/EEC relating to EMC
The EC Declaration of Conformity is available upon request for products with a CE mark. For copies of the EC
Declaration of Conformity, contact:
Eaton Power Quality Oy
Koskelontie 13
FIN-02920 Espoo
Finland
Phone: [phone]
Fax: [phone]
All manuals and user guides at all-guides.com

Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the
associated warning should be observed.
CAUTION: REFER TO OPERATOR’S MANUAL - Refer to your operator’s manual for
additional information, such as important operating and maintenance
instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries
in the trash. This product contains sealed, lead-acid batteries and must be
disposed of properly. For more information, contact your local recycling/reuse or
hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic
equipment (WEEE) in the trash. For proper disposal, contact your local
recycling/reuse or hazardous waste center.
All manuals and user guides at all-guides.com

EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
i
Table of Contents
1 Introduction 1.........................................................
Safety Warnings 1......................................................................
2 Installation 13..........................................................
Inspecting the Equipment 13................................................................
UPS Setup 13..........................................................................
UPS Shutdown 14.....................................................................
Installing the UPS Internal Batteries 14.....................................................
Tower Setup 16......................................................................
EBM Installation 18......................................................................
Hardwired PDM Installation 19..............................................................
Remote Emergency Power-off Installation 26....................................................
Plug-Receptacle PDM Installation 28..........................................................
Plug-Receptacle PDM Rear Panels 32.........................................................
3 Configuration 35........................................................
4 Operation 37...........................................................
Using Maintenance Bypass 37..............................................................
5 Specifications 39.......................................................
6 PDM Schematics 41.....................................................
7 Service and Support 49..................................................
All manuals and user guides at all-guides.com

TABLE OF CONTENTS
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
ii
All manuals and user guides at all-guides.com
all-guides.com

EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
1
Chapter 1 Introduction
The PowerPass®Distribution Module (PDM) is designed to operate with
a 5000/6000 VA Powerware®9125 uninterruptible power system (UPS).
The PDM allows you to:
SReplace or upgrade the UPS without losing power to the protected
equipment (see “Using Maintenance Bypass” on page 37).
SProvide surge protection if the UPS is not present.
SProvide extra surge protection when the UPS is present.
Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
maintenance of the UPS and PDM. Please read all instructions before operating the
equipment and save this manual for future reference.
DANGER
This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by
AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS
inside the UPS.
CAUTION
STo reduce the risk of fire or electric shock, install this UPS in a temperature and humidity
controlled, indoor environment, free of conductive contaminants. Ambient temperature
must not exceed 40°C (104°F). Do not operate near water or excessive humidity
(95% maximum).
SFor PDM models with hardwired outputs, overcurrent protection for the output AC
circuit(s) is to be provided by others.
SFor PDM models with hardwired outputs, suitably rated disconnect switches for the
output AC circuit(s) are to be provided by others.
All manuals and user guides at all-guides.com

INTRODUCTION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
2
Sikkerhedsanvisninger
VIGTIGE SIKKERHEDSANVISNINGER
GEM DISSE ANVISNINGER
Denne manual indeholder vigtige instruktioner, som skal følges under installation og
vedligeholdelse af UPS’en og PDU. Læs venligst alle instruktioner inden betjening af
udstyret og gem denne manual mhp. fremtidige opslag.
FARE
Denne UPS indeholder LIVSFARLIG HØJSPÆNDING. Alle reparationer og vedligeholdelse bør
kun udføres af en AUTORISERET SERVICETEKNIKER. Ingen af UPS’ens indvendige dele kan
repareres af brugeren.
ADVARSEL
SInstallér denne UPS i et temperatur- og fugtighedskontrolleret indendørsmiljø, frit for
ledende forureningsstoffer for at formindske risikoen for brand og elektrisk stød.
Rumtemperaturen må ikke overstige 40°C. UPS’en bør ikke betjenes nær vand eller høj
fugtighed (maksimalt 95%).
SFor PDM systemer med hårdledningsudgange, skal overstrømsbeskyttelse for
vekslestrømmens udgangskredsløb forsynes af andre.
SFor PDM systemer med hårdledningsudgange, skal egnede, nominelle afbryderkontakter
for vekslestrømmens udgangskredsløb forsynes af andre.
All manuals and user guides at all-guides.com

INTRODUCTION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
3
Belangrijke Veiligheidsinstructies
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
BEWAAR DEZE INSTRUCTIES
Deze handleiding bevat belangrijke instructies die u dient te volgen tijdens de installatie en
het onderhoud van de UPS en de PDU. Lees alle instructies voordat u de apparatuur in bedrijf
neemt en bewaar deze handleiding als naslagwerk.
GEVAAR
Deze UPS bevat LEVENSGEVAARLIJKE ELEKTRISCHE SPANNING. Alle reparaties en
onderhoud dienen UITSLUITEND DOOR ERKEND SERVICEPERSONEEL te worden uitgevoerd.
Er bevinden zich GEEN ONDERDELEN in de UPS die DOOR DE GEBRUIKER kunnen worden
GEREPAREERD.
OPGELET
STeneinde de kans op brand of elektrische schok te verminderen dient deze UPS in een
gebouw met temperatuur- en vochtigheidregeling te worden geïnstalleerd, waar geen
geleidende verontreinigingen aanwezig zijn. De omgevingstemperatuur mag 40°C niet
overschrijden. Niet gebruiken in de buurt van water of bij zeer hoge vochtigheid
(max. 95%).
SVoor PDM systemen met vast-bedrade uitgangen, moet de overstroombeveiliging voor
wisselstroom uitvoercircuit(s) door anderen worden geleverd.
SVoor PDM systemen met vast-bedrade uitgangen, moeten de juiste hoofdschakelaars
voor wisselstroom uitvoercircuit(s) door anderen worden geleverd.
All manuals and user guides at all-guides.com

INTRODUCTION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
4
Tarkeita Turvaohjeita
TÄRKEITÄ TURVAOHJEITA - SUOMI
SÄILYTÄ NÄMÄ OHJEET
Tämä käyttöohje sisältää tärkeitä ohjeita, joita on noudatettava UPS-virtalähteen ja PDM
asennuksen ja huollon yhteydessä. Lue kaikki ohjeet ennen laitteiston käyttöä ja säilytä ohje
myöhempää tarvetta varten.
VAARA
Tämä UPS sisältää HENGENVAARALLISIA JÄNNITTEITÄ. Kaikki korjaukset ja huollot on
jätettävä VAIN VALTUUTETUN HUOLTOHENKILÖN TOIMEKSI. UPS ei sisällä MITÄÄN
KÄYTTÄJÄN HUOLLETTAVIA OSIA.
VARO
SVähentääksesi tulipalon ja sähköiskun vaaraa asenna tämä UPS sisätiloihin,
joissa lämpötila ja kosteus on säädettävissä ja joissa ei ole virtaa johtavia
epäpuhtauksia. Ympäristön lämpötila ei saa ylittää 40 °C. Älä käytä lähellä vettä ja vältä
kosteita tiloja (95 % maksimi).
SPDM-järjestelmissä kiintealla asennuksella: kuormana olevien laitteiden ylivirtasuojaus
ja erotuskytkimet tulee toteuttaa kuormapiireissa.
All manuals and user guides at all-guides.com

INTRODUCTION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
5
Consignes de sécurité
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute
procédure d’installation et de maintenance de PDM et de l’onduleur. Veuillez consulter
entièrement ces instructions avant de faire fonctionner l’équipement et conserver ce manuel
afin de pouvoir vous y reporter ultérieurement.
DANGER!
Cet onduleur contient des TENSIONS MORTELLES. Toute opération d’entretien et de
réparation doit être EXCLUSIVEMENT CONFIÉE A UN PERSONNEL QUALIFIÉ AGRÉÉ.
AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR ne se trouve dans l’onduleur.
ATTENTION!
SPour réduire les risques d’incendie et de décharge électrique, installer l’onduleur
uniquement à l’intérieur, dans un lieu dépourvu de matériaux conducteurs, où la
température et l’humidité ambiantes sont contrôlées. La température ambiante ne doit
pas dépasser 40 °C. Ne pas utiliser à proximité d’eau ou dans une atmosphère
excessivement humide (95 % maximum).
SPour les models PDM ayant des sorties câblées, la protection contre une surintensité
pour le(s) circuit(s) de sortie de courant alternatif doit être fournie par un autre
fournisseur.
SPour les models PDM ayant des sorties câblées, les interrupteurs de déconnexion
convenables pour le(s) circuit(s) de sortie de courant alternatif doivent être fournie par un
autre fournisseur.
All manuals and user guides at all-guides.com
all-guides.com

INTRODUCTION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
6
Sicherheitswarnungen
WICHTIGE SICHERHEITSANWEISUNGEN
AUFBEWAREN
Dieses Handbuch enthält wichtige Anweisungen, die Sie während der Installation und
Wartung des USV (Unterbrechungsfreies Stromversorgungssystem) und der PDM befolgen
müssen. Bitte lesen Sie alle Anweisungen des Handbuches bevor sie mit dem Gerät
arbeiten. Bewaren Sie das Handbuch zum Nachlesen auf.
WARNUNG
Die USV führt lebensgefährliche Spannungen. Alle Reparatur- und Wartungsarbeiten sollten
nur von Kundendienstfachleuten durchgeführt werden. Die USV enthält keine vom Benutzer
zu wartenden Komponenten.
VORSICHT!
SUm die Brand- oder Elektroschockgefahr zu verringern, diese USV nur in Gebäuden mit
kontrollierter Temperatur und Luftfeuchtigkeit installieren, in denen keine leitenden
Schmutzstoffen vorhanden sind. Die Umgebungstemperatur darf 40°C nicht übersteigen.
Die USV nicht in der Nähe von Wasser oder in extrem hoher Luftfeuchtigkeit (max. 95 %)
betreiben.
SFür PDM-Systeme mit festverdrahteten Eingängen muß der Überstromschutz für die
Ausgangswechselstromkreise anderweitig bereitgestellt werden.
SFür PDM-Systeme mit festverdrahteten Ausgängen müssen Trennschalter für die
Ausgangswechselstromkreise mit passendem Nennwert anderweitig bereitgestellt
werden.
All manuals and user guides at all-guides.com

INTRODUCTION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
7
Avvisi di sicurezza
IMPORTANTI ISTRUZIONI DI SICUREZZA
CONSERVARE QUESTE ISTRUZIONI
Il presente manuale contiene importanti istruzioni da seguire durante l’installazione e la
manutenzione dell’UPS e dell’PDM. Leggere integralmente le istruzioni prima di utilizzare
l’apparecchiatura e conservare il presente manuale per futuro riferimento.
PERICOLO
La TENSIONE contenuta in questo gruppo statico di continuità è LETALE. Tutte le operazioni
di riparazione e di manutenzione devono essere effettuate ESCLUSIVAMENTE DA
PERSONALE TECNICO AUTORIZZATO. All’interno del gruppo statico di continuità NON vi
sono PARTI RIPARABILI DALL’UTENTE.
ATTENZIONE
SPer ridurre il rischio di incendio o di scossa elettrica, installare il gruppo statico di
continuità in un ambiente interno a temperatura ed umidità controllata, privo di agenti
contaminanti conduttivi. La temperatura ambiente non deve superare i 40°C. Non
utilizzare l’unità in prossimità di acqua o in presenza di umidità eccessiva (95% max).
SNei sistemi PDM provvisti di uscite cablate, i dispositivi di protezione da sovracorrente
per il/i circuito/i a corrente alternata in uscita devono essere forniti da terzi.
SNei sistemi PDM provvisti di uscite cablate, i sezionatori di corrente nominale adeguata
per il/i circuito/i a corrente alternata in uscita devono essere forniti da terzi.
All manuals and user guides at all-guides.com

INTRODUCTION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
8
Viktig Sikkerhetsinformasion
VIKTIGE SIKKERHETSINSTRUKSJONER
GJEM DISSE INSTRUKSJONENE
Denne håndboken inneholder viktige instruksjoner som du bør overholde ved montering og
vedlikehold av UPS-enheten og PDM. Les alle instruksjoner før utstyret tas i bruk, og gjem
håndboken til fremtidig referanse.
FARLIG
Denne UPS’en inneholder LIVSFARLIGE SPENNINGER. All reparasjon og service må kun
utføres av AUTORISERT SERVICEPERSONALE. BRUKERE KAN IKKE UTFØRE SERVICE PÅ
NOEN AV DELENE i UPS’en.
FORSIKTIG
SFor å redusere fare for brann eller elektriske støt, bør denne UPS’en installeres i et
innendørs miljø med kontrollert temperatur og luftfuktighet som er fritt for ledende,
forurensende stoffer. Romtemperaturen må ikke overskride 40°C. Den må ikke brukes i
nærheten av vann eller ved meget høy luftfuktighet (95% maks.).
SFor PDM systemer med fastkoplete uttak, må overstrømvern for vekselstrømuttak(ene)
stilles til rådighet av andre.
SFor PDM systemer med fastkoplete uttak, må passende utkoplingsbrytere for
vekselstrømuttak(ene) stilles til rådighet av andre.
All manuals and user guides at all-guides.com

INTRODUCTION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
9
Regulamentos de Segurança
INSTRUÇÕES DE SEGURANÇA IMPORTANTES
GUARDE ESTAS INSTRUÇÕES
Este manual contém instruções importantes que devem ser seguidas durante a instalação e
manutenção do no-break e da PDM. Leia todas as instruções antes de operar o equipamento
e guarde este manual para consultá-lo futuramente.
CUIDADO
A UPS contém VOLTAGEM MORTAL. Todos os reparos e assistência técnica devem ser
executados SOMENTE POR PESSOAL DA ASSISTÊNCIA TÉCNICA AUTORIZADO. Não há
nenhuma PEÇA QUE POSSA SER REPARADA PELO USUÁRIO dentro da UPS.
PERIGO
SPara reduzir o risco de incêndios ou choques elétricos, instale a UPS em ambiente
interno com temperatura e umidade controladas e livres de contaminadores condutíveis.
A temperatura ambiente não deve exceder 40°C. Não opere próximo a água ou em
umidade excessiva (máx: 95%).
SPara sistemas PDM com saídas conectadas, a proteção de sobrecarga para circuitos de
saída de corrente alternada deve ser fornecida por outros.
SPara sistemas PDM com saídas conectadas, interruptores de desconexão devidamente
qualificados para circuitos de saída de corrente alternada devem ser fornecidos por
outros.
All manuals and user guides at all-guides.com

INTRODUCTION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
10
Предупреждения по мерам безопасности
ВАЖНЫЕ УКАЗАНИЯ ПО МЕ АМ БЕЗОПАСНОСТИ
СОХ АНИТЕ ЭТИ УКАЗАНИЯ
В данном руководстве содержатся важные инструкции по установке и
обслуживанию источника бесперебойного питания (ИБП) и батарей. Перед
работой с оборудованием прочтите все инструкции. Сохраните данное
руководство для дал нейшего испол зования.
ОПАСНО
В данном ИБП имеются СМЕРТЕЛЬНО ОПАСНЫЕ НАПРЯЖЕНИЯ. Все
работы по ремонту и обслуживанию должны выполнят ся ТОЛЬКО
УПОЛНОМОЧЕННЫМ ОБСЛУЖИВАЮЩИМ ПЕРСОНАЛОМ. Внутри
ИБП нет узлов, ОБСЛУЖИВАЕМЫХ ПОЛЬЗОВАТЕЛЕМ.
ОСТО ОЖНО
SДля снижения опасности пожара или поражения электрическим током
устанавливайте ИБП в закрытом помещении с контролируемыми
температурой и влажност ю, в котором отсутствуют проводящие
загрязняющие вещества. Температура окружающего воздуха не должна
превышат 40°С. Не эксплуатируйте устройство около воды или в местах с
повышенной влажност ю (макс. 95%).
SДля моделей ИБП с постоянно запаянными выходными контактами
устройство защиты от перегрузки выходного контура (контуров)
переменного тока приобретается отдел но.
SДля моделей ИБП с постоянно запаянными выходными контактами
соответствующие размыкающие переключатели выходного контура
(контуров) переменного тока приобретаются отдел но.
All manuals and user guides at all-guides.com
all-guides.com

INTRODUCTION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
11
Advertencias de Seguridad
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
GUARDE ESTAS INSTRUCCIONES
Este manual contiene instrucciones importantes que debe seguir durante la instalación y el
mantenimiento del SIE y del PDM. Por favor, lea todas las instrucciones antes de poner en
funcionamiento el equipo y guarde este manual para referencia en el futuro.
PELIGRO
Este SIE contiene VOLTAJES MORTALES. Todas las reparaciones y el servicio técnico deben
ser efectuados SOLAMENTE POR PERSONAL DE SERVICIO TÉCNICO AUTORIZADO. No hay
NINGUNA PARTE QUE EL USUARIO PUEDA REPARAR dentro del SIE.
PRECAUCIÓN
SPara reducir el riesgo de incendio o de choque eléctrico, instale este SIE en un lugar
cubierto, con temperatura y humedad controladas, libre de contaminantes conductores.
La temperatura ambiente no debe exceder los 40°C. No trabaje cerca del agua o con
humedad excesiva (95% máximo).
SPara los sistemas PDM con salidas cableadas permanentamente, la protección contra
exceso de corriente para el/los circuito(s) de CA de salida será suministrada por terceros.
SPara los sistemas PDM con salidas cableadas permanentemente, los interruptores de
desconexión debidamente clasificados para el/los circuito(s) de CA de salida serán
suministrados por terceros.
All manuals and user guides at all-guides.com

INTRODUCTION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
12
Säkerhetsföreskrifter
VIKTIGA SÄKERHETSFÖRESKRIFTER
SPARA DESSA FÖRESKRIFTER
Den här anvisningen innehåller viktiga instruktioner som du ska följa under installation och
underhåll av UPS-enheten och PDM. Läs alla instruktioner innan du använder utrustningen
och spara den här anvisningen för framtida referens.
FARA
Denna UPS-enhet innehåller LIVSFARLIG SPÄNNING. ENDAST AUKTORISERAD
SERVICEPERSONAL får utföra reparationer eller service. Det finns inga delar som
ANVÄNDAREN KAN UTFÖRA SERVICE PÅ inuti UPS-enheten.
VIKTIGT
SMinska risken för brand eller elektriska stötar genom att installera denna UPS-enhet
inomhus, där temperatur och luftfuktighet är kontrollerade och där inga ledande
föroreningar förekommer. Omgivande temperatur får ej överstiga 40°C. Använd inte
utrustningen nära vatten eller vid hög luftfuktighet (max 95 %).
SÖverströmsskydd för de utgående växelströmskretsarna ska tillhandahållas av andra för
PDM-system med fasta utgångar.
SBortkopplingsswitchar med passande dimensionering för de utgående
växelströmskretsarna ska tillhandahållas av andra för PDM-system med fasta utgångar.
All manuals and user guides at all-guides.com

EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
13
Chapter 2 Installation
This section explains:
SEquipment inspection
SUPS setup
SExtended Battery Module (EBM) installation
SPowerPass Distribution Module and UPS installation
SRemote emergency power-off (REPO) installation
SPDM rear panels
Inspecting the Equipment
If any equipment has been damaged during shipment, keep the shipping
cartons and packing materials for the carrier or place of purchase and file
a claim for shipping damage. If you discover damage after acceptance,
file a claim for concealed damage.
To file a claim for shipping damage or concealed damage: 1) File with
the carrier within 15 days of receipt of the equipment; 2) Send a copy of
the damage claim within 15 days to your service representative.
NOTE Check the battery recharge date on the shipping carton label. If the date has expired
and the batteries were never recharged, do not use the UPS. Contact your service
representative.
NOTE Inspect the battery trays for any loose connections. If any damage occurred during
shipment, file a shipping claim as stated above.
UPS Setup
The Powerware 9125 UPS is designed for flexible configurations and can
be installed in a rack or as a standalone cabinet.
If the UPS is already installed and operating, shut down the UPS before
installing the PDM. See the following section, “UPS Shutdown.”
For new UPS installations, continue to “Installing the UPS Internal
Batteries” on page 14 to begin the UPS setup.
All manuals and user guides at all-guides.com

INSTALLATION
EATON Powerware®9125 Two-in-One PDM (5000/6000 VA) User’s Guide S164201519 Rev E
www.powerware.com
14
UPS Shutdown
If the UPS is already installed and operating, use the following procedure
to shut down the UPS:
1. Prepare your equipment for shutdown.
2. Press and hold the Off button for approximately three seconds.
The μindicator begins to flash. The UPS switches to Standby
mode (if utility power is available) and removes power from your
equipment.
3. Unplug the UPS; the UPS shuts down in five seconds. The bar
graph and battery indicators flash briefly prior to shutdown.
4. Disconnect the power cord from the UPS input connector.
5. Disconnect the protected equipment power cord from the UPS.
6. Continue to “Hardwired PDM Installation” on page 19 or
“Plug-Receptacle PDM Installation”on page 28.
Installing the UPS Internal Batteries
CAUTION
The UPS battery trays are heavy (28.1 kg/62 lb). A minimum of two people are required to lift
the battery trays into the UPS chassis.
NOTE For new rack-mounted installations, follow the instructions with the rail kit before
installing the internal batteries.
To install the battery trays into the UPS chassis:
1. Verify that the battery circuit breaker on the UPS rear panel is in the
OFFposition(seeFigure6onpage18).
2. Slide the battery trays into the chassis (see Figure 1).
Figure 1. Installing the Battery Trays
All manuals and user guides at all-guides.com