Echogear EGMF1 User manual

5/16 x 2¾ in.
4 mm
Hex Key
Lag Bolts TV Screws
Extender Brackets
Extender
Screws
Wallplate and Arm
Lag Bolt Washers
TV Washers
Spacers
M4 x 12mm
M6 x 12mm
M6 x 35mm
22mm
M4 x 35mm
M8 x 16mm
M8 x 25mm M8 x 35mm
M8 x 50mm
2.5mm
M
4
/
M
5
M
6
/
M
8
Stud
Finder Awl or Thin Nail Pencil Level
Drill 1/2 in.
(13 mm)
7/32 in.
(5.5 mm)
Wood
7 ⅞ in.
(200 mm)
7 ⅞ in.
(200 mm)
5 ⅛ in.
(130 mm)
5 ⅛ in.
(130 mm)
4 in.
(100 mm)
4 in.
(100 mm)
15 ¾ in.
(400 mm)
15 ¾ in.
(400 mm)
13 ⅜ in.
(340 mm)
13 ⅜ in.
(340 mm)
11 ¾ in.
(300 mm)
11 ¾ in.
(300 mm)
Getting Started
Tools Needed
Hardware Included
Does your TV (including accessories)
weight more than 60 lbs. (27 kg) ?
No — Perfect!
Yes — This mount is NOT compatible.
Please read through these instructions completely to be sure you’re comfortable with
this easy install process. Also check your TV owner’s manual to see if there are any
special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the
installation, assembly or use of this product, contact Customer Service at 1-855-428-2490.
CAUTION: Avoid potential personal injuries and property damage!
●This product is designed for use in wood stud walls - DO NOT install into drywall alone
●The wall must be capable of supporting five times the weight of the TV and mount combined
●Do not use this product for any purpose not explicitly specified by manufacturer
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
FULL-MOTION
TV WALL MOUNT
Model EGMF
1
xHeight
Width
W
H
mm mm
08
x4
x4
05
x2
x2
04
x8
x8
06
x2
x2
07
x1
x1
09
x4
x4
10
x4
x4
11
x4
x4
12
x4
x4
13
x4
x4
14
x4
x4
15
x4
x4
16
x4
x4
18
x8
x8
17
x4
x4
19
x4
x4
01
x1
x1
02
x2
x2 03
x2
x2
03
02
03
02
100 mm = 10 cm ≈ 4 in.
130 mm = 13 cm ≈ 5 1/8 in.
200 mm = 20 cm ≈ 7 7/8 in.
300 mm = 30 cm ≈ 11 3/4 in.
340 mm = 34 cm ≈ 13 3/4 in.
400 mm = 40 cm ≈ 15 3/4 in.
Using the hex key 07 , remove
the screws [S] and separate
the faceplate from the arm.
Keep screws for use in Step 6.
Measure your TV hole pattern. Determine which
TV bracket
configuration
Aor Bto use
based on your
TV hole pattern
measurements
from STEP 2.
If your TV hole pattern is greater than 200 mm x 200 mm
(configuration B), attach TV bracket extenders 02 and
03 to faceplate using extender screws 04 .
[S]
60 lbs.
(27 kg)
WARNING: Exceeding the weight capacity
can result in serious personal injury or damage
to equipment! It is the installer's responsibility
to make sure the weight of the TV (with
accessories) does not exceed 60 lbs (27 kg).
What is your wall made of?
Drywall with
wood studs?
Not Sure?
Perfect!
Call Customer Service:
1-855-428-2490
?
STEP 1 STEP 2 STEP 3
WARNING: This product
contains small items that could be
a choking hazard if swallowed.
Before starting assembly,
verify all parts are included and
undamaged. If any parts are
missing or damaged, do not return
the damaged item to your dealer;
contact Customer Service.
Never use damaged parts!
NOTE: Not all parts and
hardware included will be used.
A
B
04
07
07

Milestone AV Technologies and its aliated
corporations and subsidiaries (collectively,
“Milestone”), intend to make this manual accurate
and complete. However, Milestone makes no
claim that the information contained herein
covers all details, conditions, or variations. Nor
does it provide for every possible contingency
in connection with the installation or use of
this product. The information contained in this
document is subject to change without notice
or obligation of any kind. Milestone makes no
representation of warranty, expressed or implied,
regarding the information contained herein.
Milestone assumes no responsibility for accuracy,
completeness or suciency of the information
contained in this document.
©2017 Milestone AV Technologies. All rights
reserved. ECHOGEAR is a Milestone brand.
ECHOGEAR and the ECHOGEAR logo are
trademarks of Milestone.
Made in China.
Milestone Global Headquarters • 6436 City West Parkway • Eden Prairie, MN 55344 USA 6901-002430 05
Adjustments
5-1
4-1
4-2
5-2 5-3 5-4
TO ADJUST TV LEVEL,
loosen screws [S] on
the rear of the arm
plate, adjust level, and
retighten to secure.
TO ADJUST THE TILT, first rotate (loosen or tighten) the tilt lever
as far as you can, then:
aPull and hold the lever outward,
bRotate the lever in the opposite direction,
cRelease the lever back into position,
dRotate the lever to tighten or loosen.
Repeat as needed.
LOOSEN: to adjust the TV tilt position.
TIGHTEN: to set the TV in place at your desired tilt angle.
ab d c
[S] 07
Loosen
Tighten
Drill two pilot holes using a 7/32 in. (5.5 mm)
diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth
of 3 in. (75 mm). Be sure to drill into the center of the stud.
01
01
01
Locate your stud. Verify and mark the center of
the stud by finding the stud edges using an awl,
a thin nail, or an edge-to-edge stud finder.
Position the wall plate 01 at your desired height
and line up the holes with your stud center line.
Level the wall plate and mark the holes.
IMPORTANT: Be sure to only use the top hole
and bottom slot for mounting.
Hang TV onto arm
and using hex key
07
, secure with
screws [S] saved
from
Step 1 .
IMPORTANT:
These
screws [S]
must be installed to
secure the TV onto
the arm 01 .
07
[S]
05 06
05
06
STEP 6
STEP 5 Wall Plate Install (Wood Stud)
(a) Flat Back
configuration Billustrated configuration Billustrated
(b) Round Back / Extra Space
CAUTION: Avoid potential personal injuries
and property damage!
●Drywall covering the wall must not exceed
5/8 in. (16 mm)
●Minimum wood stud size: common 2 x 4 in.
(51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
CAUTION: Avoid potential personal injury
or property damage! All lag bolts 05 MUST BE
firmly tightened to prevent unwanted movement
of the wall plate 01 .
CAUTION: Ensure the wall plate is
securely fastened to the wall before continuing
on to the next step.
M4 M6 M8
3 in. (75 mm)
7/32 in.
(5.5 mm)
Position your TV bracket
configuration Aor Bover your
TV hole pattern - making sure
the bracket is centered and level
over the TV hole pattern.
Secure the bracket using your
screw/washer/spacer selection:
(a) for Flat Back
(b) for Round Back / Extra Space
CAUTION: Ensure TV
bracket is securely fastened
before moving on to the next step.
10 14
16
16
18 19
11 15
17
17
09 13 08 12
STEP 4 Install TV bracket
Install wall plate 01 using lag bolts 05 and
washers 06 . Tighten the lag bolts 05 only until
they are pulled firmly against the wall plate 01 .
Note Orientation
FLAT BACK ROUND
BACK CABLES
INSET
HOLES
abToo Short
Too Long
Correct
If your TV has a flat back, AND you want your TV
closer to the wall, use the shorter screws (a).
Use spacers and long screws (b) to accommodate:
• Round/irregular back TVs
• TVs with inset mounting holes
• Extra space needed for cables
CAUTION: Verify
adequate thread engagement
with the screw/washer/spacer
combination AND TV bracket.
-Too short will not hold the TV.
-Too long will damage the TV.
Determine which
screw diameter (M4,
M6, or M8) to use.
Alternate
Setups