Echogear EGLT1 User manual

5/16 x 2¾ in.
Wall Plates Left TV
Bracket
Right TV
Bracket Lag Bolts
Lag Bolt
Washers
Connection
Plate Screws
M5 x 8mm
TV Screws TV Washers
Spacers
M4 x 12mm
M4/M5 M6/M8
M6 x 12mm M6 x 35mm
M4 x 35mm
M8 x 16mm M8 x 35mm
M8 x 20mm
LARGE TILT
TV WALL MOUNT
For 32”-70”
(81.3-177.8 cm)
TVs
Model EGLT1
M6M4 M8
1-1 Select TV Screw Diameter 1-2 Select TV Screw Length
FLAT BACK ROUND BACK CABLESINSET HOLES
AB
Too Short
Too Long
Correct
Stud
Finder Awl or Thin Nail Pencil Level
Drill 1/2 in.
(13 mm)
Socket
7/32 in.
(5.5 mm)
Drill Bit
Tools: Hardware
08 x4
06 x4
03 x4
07 x4
09 x4
10 x4
13 x4
15 x4
14 x4 11 x4
12 x4
16 x4
17 x4
01 x1 02 x1
04 x1 05 x1
Position your TV
bracket configuration
(Aor B)over your TV
hole pattern - making
sure the bracket is
centered over the
TV hole pattern and
level. Secure bracket
using your screw/
washer (A-Flat Back)
or spacer/screw/
washer (B-Round
Back / Extra Space)
selection.
CAUTION:
Ensure TV bracket
is securely fastened
before moving on to
the next step.
1-3 Attach the TV Bracket
If your TV has a flat back AND you want your TV closer to
the wall, use the shorter screws (a).
Use the spacers and longer screws (b) to accommodate:
• Round/irregular back TVs
• TVs with inset mounting holes
• Extra space needed for cables
CAUTION:
Verify adequate thread
engagment with the screw or
screw/spacer combination.
-Too short will not hold the TV.
-Too long will damage the TV.
Standard configurations
are shown. For special
applications, or if you
are uncertain about your
hardware selection,
contact Customer Service
at 1-855-428-2490.
Hand thread screws into the threaded inserts
on the back of your TV to determine which
screw diameter (M4, M6, or M8) to use.
125 lbs.
(57 kg)
Does your TV weight more
than 125 lbs. (57 kg) including
accessories?
No — Perfect!
Yes — This mount is NOT compatible.
WARNING: Exceeding the weight
capacity can result in serious personal injury
or damage to equipment! It is the installer's
responsibility to make sure the weight of the
TV (with accessories) does not exceed 125 lbs
(57 kg).
10
15
11
16
0908
04
04
A
B14
15
17
16
1312
05
05
04
04
WARNING: This
product contains small
items that could be
a choking hazard if
swallowed.
Before starting
assembly, verify all
parts are included and
undamaged. If any parts
are missing or damaged,
do not return the
damaged item to your
dealer; contact Customer
Service. Never use
damaged parts!
Please read through these instructions completely to be sure you’re comfortable with this
easy install process. Also check your TV owner’s manual to see if there are any special
requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the
installation, assembly or use of this product, contact Customer Service at 1-855-428-2490.
CAUTION: Avoid potential personal injuries and property damage!
●This product is designed for use in wood stud walls - DO NOT install into drywall
alone
●The wall must be capable of supporting five times the weight of the TV and mount
combined
●Do not use this product for any purpose not explicitly specified by manufacturer
●Manufacturer is not responsible for damage or injury caused by incorrect assembly
or use
Drywall with
wood studs?
Perfect!
Call Customer Service:
1-855-428-2490
?
What is your wall made of?

Milestone AV Technologies and its aliated corporations and subsidiaries (collectively, “Milestone”), intend to make
this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all
details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or
use of this product. The information contained in this document is subject to change without notice or obligation of any
kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein.
Milestone assumes no responsibility for accuracy, completeness or suciency of the information contained in this
document.
©2015 Milestone AV Technologies. All rights reserved. ECHOGEAR is a Milestone brand. ECHOGEAR and the ECHOGEAR
logo are trademarks of Milestone.
Made in China.
Milestone Global Headquarters • 6436 City West Parkway • Eden Prairie, MN 55344 USA
16 - 24 in.
(406 - 610 mm)
16 - 24 in.
(406 - 610 mm)
3-1 3-2
3-3 3-4
6901-002431 02
Assemble
the wall plate
sections 01 and
02 with the
connection plate
screws 03 .
Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Be sure to drill into the center of the stud.
IMPORTANT: Pilot holes must be drilled to a depth of 3 in. (75
mm).
06
07
01
02
Check knobs on brackets 04 and
05 to ensure that they are tight
before hanging TV. If you desire a
degree of tilt, loosen the knobs, adjust
the tilt and retighten.
NOTE: It will be necessary to remove
the TV from the wall plate assembly to
make tilt adjustments.
Unscrew locking screws [LS] on brackets 04
and 05 enough to clear the bottom of the wall
plate assembly.
Hang the TV with brackets 04 and 05 onto the
wall plate assembly.
Locate your
stud. Verify
and mark
the center
of the stud
by finding the
stud edges using
an awl, a thin
nail, or an edge-
to-edge stud finder.
Position
the wall
plate
assembly
at your desired
height and line
up the holes with
your stud center
line. Level the wall plate
and mark the holes.
01
02
[LS]
[LS]
Install the
wall plate
assembly using lag
bolts
06
and washers
07
. Tighten
the lag bolts
06
only until
the washers
07
are pulled firmly against the
wall plate assembly.
Step 3 Wood Stud
Step 4 Tighten Knobs
Step 5 Hang TV
Step 6 Secure TV
Step 2 Assemble Wall Plate
3 in. (75 mm)
7/32 in.
(5.5 mm)
05
05
05
04
04
04
01
02
Tighten the locking screws [LS] on
brackets 04 and 05 to secure the
TV to the wall plate assembly.
03
CAUTION: Avoid potential personal injuries and property damage!
●Drywall covering the wall must not exceed 5/8 in. (16 mm)
●Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
CAUTION: Avoid potential personal injury or property damage! All lag bolts 06 MUST BE firmly tightened to prevent
unwanted movement of the wall plate assembly.
CAUTION: Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step.