EDS SD800 User manual

SD800
Fire Alarm Systems / Telephone Dialer
SPECIFICATIONS PHYSICAL
CONNECTIONS
Model SD800
Environmental class II Indoor
Electrical
Operating voltage 24V DC ± %10
Stand-by current <50 mA
Alarm current <100mA
Controller Microprocessor
Line frequency 390-490Hz
Keyboard Built-in
Call
Called phone number 8
Called period Tone:70s Pulse:80s
Audio recoding period 16s
Unanswered / Busy 5 times
Unanswered calling period 50s
Unanswered call number 10 times
Alarm
Alarm input Programmable, 5 time call
Alarm detection Available
Password
User password 6
Programing password 1
Relay puller with password Available
Tone / Pulse options Available
Restore factory settings Available
General
Housing material / shape Card / Standard
Operating Temperature -10OC~+50OC
Dimension (HxWxD) 90x80x25mm
Dimension Box (HxWxD) 110x110x39mm
Weight card 82g
Year of Manufacture The year and week of manufacture is included in the rst four
digit of your product serial number (located on the product
identication label)
Manufacturer EDS Elektronik Destek Sanayi ve Ticaret Ltd.
Meclis Mah. Teraziler Cad. Hayran Sk. No: 4 34785 Sancaktepe
/ İstanbul / Turkey
Recycle
12.19V2Address: Meclis Mah. Teraziler Cad. Hayran Sk. No: 4 34785 Sancaktepe / Istanbul / Turkey [phone] I [email protected] I www.eds.com.tr
Voice Recording
Press the SW1 key (the red REC LED shall light up) and read the
message to be recorded.
When the record key is released or after 16 seconds, the voice
recording shall be completed.
Note: During recording, speak with a normal voice from a
distance of 20 cm to the microphone.
Exiting the Programming Mode
To exit the programming mode, press and hold the “*” and “#”
keys simultaneously for more than 3 seconds.
Note: If there is no command in 2m ms system exits
programmable mode.
Entering the Numbers to be dialled
After the device is switched to the programming mode, 8
different land- or mobile telephone numbers can be recorded.
When the device receives a signal, all the numbers are dialled
in order and the recorded message is read.
PROGRAMMING
Introduction to Programming Mode
In order to enter the telephone numbers to be dialled in
the device and to make the settings, one must rst enter the
programming mode.
To enter the programming mode, press and hold the “*” and “#”
keys simultaneously for 3 seconds.
1#(tel no)# 1. The number record to be dialled rst.
2#(tel no)# 2. The number record to be dialed second.
3#(tel no)# 3. The number record to be dialled third.
4#(tel no)# 4. The number record to be dialled fourth.
5#(tel no)# 5. The number record to be dialled fth.
6#(tel no)# 6. The number record to be dialled sixth.
7#(tel no)# 7. The number record to be dialled seventh.
8#(tel no)# 8. The number record to be dialled eighth.
Note: To delete a recorded number from the memory, 0 is written
instead of the (tel. no.) in the above commands.
For example: 3#0# deletes the 3rd record.
80
90
39
1
3
2
4
Cable Input Holes
Mounting
Ports
Supply
Trigger
3
4
1
1
1
1
2
2

SD800
Fire Alarm Systems / Telephone Dialer
12.19V2Address: Meclis Mah. Teraziler Cad. Hayran Sk. No: 4 34785 Sancaktepe / Istanbul / Turkey [phone] I [email protected] I www.eds.com.tr
Entering the Numbers to be Dialled
* and # keys enter the programming mode.
*0 #: Calling starts with negative triggering (factory default).
*1 #: Calling starts with positive triggering.
*2 #: Calling is made as long as the trigger is received and stopped when
the trigger stops (factory default).
*3 #: Calling starts when the trigger is received and stops when all the
numbers are dialled.
*4 #: The voice recording plays for 45 seconds (factory default).
*5 #: The voice recording plays for 90 seconds.
*6 #: DMTF dialling mode.
*7 #: Call with dialling (factory default).
*8 #: The calling cannot be stopped after triggering with pressing the 0 key
for a long time (factory default).
*9 #: The calling can be stopped after triggering with pressing the 0 key for
a long time
0.N#: All the numbers recorded in the memory shall be dialled N times.
(Dialling 2 times is the factory default).
(e.g. 03# means that each number shall be dialled 3 times.)
*## resets to the factory default. Note: Recorded phones erased.
* and # keys exit the programming mode.
MOUNTING
From the mounting port
(2) assemble the device.
‘Use 4 units of M4+52 metal
screw and M8 dubel (plastic
screw holder in-wall).
Close the cover.
Fix the sounder from
bottom with two screws.
Technical specications are subject to change without prior notice.