EDS AS290 User manual

AS290
INTRUSION ALARM SYSTEMS
OUTDOOR SOUNDER
Installation Manual
www.edselectronic.com

1
1
EDS Sounders are designed to give visual and audible warning in case of
intrusion. We are expert in manufacturing sounders. We offer customise
products for our customers with providing wide range of selections in color,
shape, technical components and logo printing.
2
1
1
280
270
1

2
3
<30mA
300mA
<
102dB-108dB
1
-10OC / + 50OC
Model AS290
Electrical
2.0-3.3Khz
selectable
Flashing LED
270x280x70mm
917g
Built-in Battery
Running LED display
(Alarm)
(Stand-by)
Selectable (5 min)
Programmable sounder period

3
Electrical Connections
A
A
B
C
D
E
F
B
CE
F
D
Tamper
Supply
Sounder Trigger
Micro Switch
Buzzer
Battery
JP7
JP4
JP2
JP3
JP1
Factory Defaults Values
JP 1 Off
JP 2 Off
JP 3 Off
JP 4 Off
JP 7 Negative
Note: JP1 feature activated
when supply is from the
panel.
Jumper Function Off On
JP1 Voltage type Sounder supply is
from panel
JP2 Start time set-up -5 min.
4
Sounder supply is from
battery
JP3 Trigger type Negative Positive
JP4 Siren period 5 min. 15 min.
JP7 JP3 should be set to whichever type of trigger is
selected. JP7 can not be used as stand alone.

4
Panel Connection
MOUNTING
PREMIER 412/816GENERAL CADDX NX-4/6/8
1 2 3
Sounder Trigger Supply Tamper
1 2 3
1 2 3
1
2
1
2
1 2 3
5
Turn the sounder upside-down to open the cover.
Push the latch upwards and pull the cover below.
Opening the top cover before mounting

H
5
Mounting to the Wall
Take out the mounting screw (A).
Place the battery to the slot (E).
Be careful with the polarities and the direction of the battery.
Mark the screw holes and suspender places on the wall with the aid
on the box or template on the package for mounting.
There are 4 screw and 1 hanger place (B) and for cable connection
there is a 1 cable connection terminal (D) as illusturated in the package.
A
F
D
B
E
C
H
Screw for upper cover
Hanger
Mounting points
Cable terminal
Battery slot
Protective Cover
Protective Cover
A
B
C C
C
C
D
E
F
G
Placing Protective Cover
Set the electricity connections of the card
as shown in electricity Connections and draw
attention to the panel connection reference
section.
After completing the electricity and battery
connections, as shown in the gure 1 place the
transparent protection cover on the card (H).
Figure 1

6
I
G
Metal Sheet (Optional)
Screw Mounting Location
Attaching the Top Cover
Place the ‘1’ nails as they would t into the
‘2’ holes as shown in Figure 2 and make the
latch be attached to ‘G’ point by pressing the
top cover.
Opening The Top Cover After Mounting
Push ‘G’ latch shown in the Figure 2 with a
straight screw and lift the
top cover.
Push the cover upwards to let the ‘1’ nails
release and remove the cover.
Mounting the Metal Cover
Mount the optional metal cover as shown
in Figure 3.
Important Mounting Notes
It should be at least 5cm below the ceiling
in order to be able to open the top cover
during assembly.
Choose a clean and smooth surface for
easy mounting. Use 4 units of M4+52 metal
screw and M8 dubel.
I
Figure 3
G
1
2
1
2
Figure 2

6
Keep the manual, observe all warnings, Follow the instructions
respectively.
Do not throw battery into the re.
Do not reverse charge.
Do not short-circuit.
For better audio performance mount the device to a smooth surface.
Turn off the power immediately and contact the technician when a problem
occurs.
V1. 29.04.2019
WARNING
Scan this code with your
smartphone to visit
www.edselectronic.com
EDS Elektronik Destek San. Ve Tic. Ltd. Şti.
Meclis Mah. Teraziler Cad. Hayran Sok. No:4 34785
Sancaktepe / İstanbul / Türkiye [phone]
[email protected] / www.edselectronic.com