QUICK INSTALL GUIDE EL-SC-300
2 3
IMPORTANT SAFETY INSTRUCTIONS
1. Read, understand and follow ALL safety and installation instructions included in this
manual. Failure to follow the included documentation may damage the product and will void
manufacturer’s warranty.
2. Follow ALL installation guidelines included with the product. Installation of the product in high
humidity environments, in close proximity to heat sources and /or non-recommended locations
will impede, interfere and/or damage the intended operation of the product.
3. Only use attachments and accessories which have been specified for use by the manufacturer.
4. The use of abrasive, liquid or solvent based cleaning fluids will damage the product. Please refer
and follow all Product Care instructions included with the product.
5. Product Servicing may only be completed by authorized or certified service centers & personnel.
For a complete list of product servicing options, please follow instructions included in the
product documentation and /or contact original manufacturer for details.
FCC and IC Information:
This Class B digital apparatus complies with Part 15 of the FCC rules and with Canadian ICES-003 and
RSS-247.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-247.
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer
d’interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent
affecter son fonctionnement.
Warning:
Changes or modications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
FCC and IC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and
meets the exemption from the routine evaluation limits in section 2.5 of RSS 102.
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters from user and bystanders.
Warning:
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102, and users can
obtain Canadian information on RF exposure and compliance from the Canadian Representative Product
Solutions Group at Tel: (519) 763-4538.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/ TV technician for help.
La puissance de sortie émise par l’appareil de sans l est inférieure à la limite ‘exposition aux fréquences
radio d’Industry Canada (IC). Utilisez l’appareil de sans l de façon à minimiser les contacts humains
lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux
limites d’exposition aux RF d’IC dans des conditions d’exposition à des appareils mobiles (antennes sont
supérieures à 20 cm à partir du corps d’une personne).
FCC and IC Registrations
FCC ID: EF400211
IC: 1078A-00211
Z-Wave Operating Frequency
Australia/New Zealand: 921:42/921.40/919.80MHz
US/Canada: 908.42.908.40/916MHz
European: 868.42/868.40/869.85MHz
Z-Wave Developer’s Kit: 7.13.1
This product can be operated in any Z-Wave™ network with other Z-Wave certied devices from other
manufacturers. All mains operated nodes within the network will act as repeaters of vendor to increase
reliability of the network.
In an Elan SC Series System Controller, the host application controls the device reset feature.
If this controller is the primary controller for your network, resetting it will result in the nodes in your
network being orphaned and it will be necessary after the reset to exclude or re-include all of the
nodes in the network. If this controller is being used as a secondary controller in the network, use this
procedure to reset the controller only in the event that the network primary controller is missing or
otherwise inoperable.
